3D Printing Info

Filament comparison

ABS-GF vs PVA

Compare printing settings, strength, heat resistance, dated prices and sources.

Glass-fibre ABS (ABS-GF) guidePVA (soluble support) guide

2 selected · all documented properties

Open these two in the interactive comparisonMore ABS-GF comparisonsMore PVA comparisons
ABS-GF vs PVA — documented properties and sources
PropertyGlass-fibre ABS (ABS-GF)ABSPVA (soluble support)SUPPORT
Market snapshot
Listing priceUSD/kg; dated snapshots$34.99/kg median; $24.49–$73.33/kg across 4 dated product listings$65.98/kg median; $42.00–$96.00/kg across 5 dated product listings
Identity & Market
Base polymer / chemistryABS reinforced with chopped glass fibre — 3DXTech's grade is nominally 10 wt%[1][2]Polyvinyl alcohol — a water-soluble support polymer[3][4]
Densityg/cm³1.08 (Bambu Lab) and 1.15 (3DXTech), ISO 1183[2][1]0.6–0.9 (3DXTech AquaTek, ISO 1183) and 1.13 (Polymaker PolyDissolve S1)[3][4]
Typical priceUSD/kg1 kg-equivalent spools span 24–73; the middle of the market is about 35[5][6][7][8]1 kg-equivalent spools span 42–96; the middle of the market is about 66[6][9][10][11]
Price range across brandsUSD/kg24–73 across brands; Siraya Tech 24, Bambu Lab 30, SUNLU 40, 3DXTech 73[5][6][7][8]42–96 across brands; IEMAI 3D E-WATER 42, YXPOLYER 55, Reli3D 66 at 500 g, Polymaker PolyDissolve S1 67 at 750 g, 3DXTech AquaTek 96 at 750 g in 1.75 mm[6][9][10][12][11]
Market availability1–5Available from several mainstream brands[5][6]Stocked by most mainstream brands[6][9][10][12][11]
Spool sizes & diameters1.75 and 2.85 mm; 750 g and 1 kg spools[6][5]1.75 and 2.85 mm; 0.5 and 0.75 kg spools[6][9]
Typical applicationsStiff, dimensionally stable enclosure and tooling parts; Bambu Lab notes the fibre blurs layer lines into a matte finish[2]Dissolvable support for PLA, TPU, PVB and PETG — Polymaker names those four for PolyDissolve S1[4]
Printing Parameters
Nozzle temperature°C240–280 (Bambu Lab)[2]215–225 (Polymaker PolyDissolve S1)[4]
Bed temperature°C80–100 (Bambu Lab)[2]25–60 (Polymaker PolyDissolve S1)[4]
Enclosure / chamber requirement1–5Enclosure recommended — Bambu Lab specifies a 45–60 °C chamber[2][13]Open frame is fine[4]
Recommended chamber temperature°C45–60 (Bambu Lab)[2]Not documented
Part cooling fan0–80 % (Bambu Lab)[2]Part cooling fan required (Simplify3D)[14]
Bed surface & adhesion aidClean the plate and apply glue; Simplify3D also lists Kapton tape and ABS slurry[13][15]PEI sheet or painter's tape[14]
Maximum volumetric flow (mm³/s; see test conditions)mm³/s14 at Bambu Lab's 180 mm/s cap on a 0.4 mm nozzle at 0.2 mm layer[2][16]4–12 at Polymaker's 50–150 mm/s on a 0.4 mm nozzle at 0.2 mm layer[4]
Warping tendency1–5Moderate — needs adhesion aid or draught shield; Bambu Lab positions the fibre as reducing warping[2]Not documented
Bed-adhesion difficulty1–5Needs a specific surface plus adhesive[13]Sticks to most surfaces[14]
Stringing / oozing tendency1–5Slight — Polymaker advises 1–2 mm retraction at 20–30 mm/s[17]Moderate — retraction tuning needed[14]
Overall printing difficulty1–5Intermediate — dry filament and a tuned profile; hardened nozzle mandatory[13]Intermediate — dry filament and a tuned profile; PVA is unusable once it has taken up moisture[18][4]
Extruder requirementNot documentedA second extruder or a tool changer; PVA is a support material, not a model material[4]
Hardware Wear & Reliability
Nozzle hardness required1–4Hardened steel required[13]Brass fine indefinitely[4]
Abrasiveness1–5Highly abrasive — standard GF composite[13]Non-abrasive[4]
Nozzle clog risk1–5Moderate — needs dry filament and a clean nozzle; 3DXTech specifies a hardened 0.4 mm minimum nozzle and 0.25 mm layers or higher for the glass-filled grade[19][20]Very high — frequent jams without careful setup; wet PVA foams and carbonises in the nozzle[18]
Heat-creep / jam sensitivity1–5Slightly sensitive[15]High — all-metal hotend and strong cooling needed; Simplify3D warns PVA clogs if the nozzle is left hot while not extruding[14]
Hotend requirementNo special hot-end required[15]No special hot-end required, but the nozzle must not be parked hot[14]
Moisture Behaviour
Moisture absorption (hygroscopicity)1–5Moderate — 0.53 % saturated at 25 °C / 55 % RH (Bambu Lab)[2]Very high (>2 %) — Polymaker measures 10.21 % equilibrium water absorption, by far the highest in the dataset[4]
Equilibrium moisture content at ~50 % RH%0.53 saturated at 25 °C / 55 % RH (Bambu Lab)[2]10.21 equilibrium water absorption (Polymaker PolyDissolve S1)[4]
Drying temperature & time80 °C for 8 h (Bambu Lab)[2]Not documented
Symptoms when wetBubbling and popping at the nozzle, stringing and a rough surface[18]Bubbling and popping at the nozzle, stringing and a rough surface; with PVA this progresses to clogging[18]
Effect of moisture on strengthPolymaker rates ABS moderate-sensitivity and publishes no dry-versus-conditioned figures; absorbed water flashes to steam in the hotend and shows as bubbling and poor layer adhesion[18]Polymaker groups PVA with nylon as the most moisture-prone class and says it often has to stay in a dryer while printing; there is no published dry-versus-conditioned strength comparison because PVA is not a structural material[18]
Storage requirementSealed with desiccant; Polymaker rates ABS moderate-sensitivity[18]Sealed with desiccant at all times; PVA takes up water faster than any other filament here[18][4]
Mechanical Properties
Tensile strength (XY)MPa36 ± 3 printed XY, ISO 527 (Bambu Lab); 3DXTech quotes 68 at break[2][1]Not documented
Young's modulusMPa3160 ± 170 printed XY, ISO 527 (Bambu Lab); 3DXTech quotes 4210[2][1]Not documented
Elongation at break%6.3 ± 1.2 printed XY, ISO 527 (Bambu Lab); 3DXTech quotes 2 at break[2][1]Not documented
Flexural strengthMPa68 ± 4 printed XY, ISO 178 (Bambu Lab); 3DXTech quotes 70[2][1]Not documented
Flexural modulusMPa2860 ± 130 printed XY, ISO 178 (Bambu Lab); 3DXTech quotes 4420[2][1]Not documented
Charpy impact, notchedkJ/m²4.2 ± 1.1 printed XY, ISO 179, notched (Bambu Lab)[2]Not documented
Other impact dataCharpy unnotched 14.5 ± 1.5 printed XY (Bambu Lab, ISO 179)[2]Not documented
Layer adhesion / Z tensileMPa29 ± 3 printed Z, ISO 527 (Bambu Lab)[2]Not documented
Brittleness1–5Brittle — snaps with little warning; notched Charpy falls from 21.5 to 4.2 kJ/m² against unfilled Bambu Lab ABS[2][21]Not documented
Creep resistance / sustained load1–5Good — no creep test found; chopped glass fibre lifts modulus to 3160 MPa against 2200 for unfilled Bambu Lab ABS[2][21]Poor — deforms under load at room temperature; PVA is not used structurally[3]
Fatigue / repeated-flex resistance1–5Below average — no S-N curve found; notched Charpy falls to 4.2 kJ/m² against 21.5 for unfilled Bambu Lab ABS[2][21]Poor — fails after a few cycles[3]
Elasticity / flexibility1–5Rigid[2]Not documented
Z strength as % of XY%81 (Bambu Lab, printed Z against XY tensile)[2]Not documented
Wear resistance & frictionNot documented3DXTech marks tensile strength, modulus and elongation as not applicable for its PVA support grade — it is not characterised as a structural material[3]
Thermal Properties
HDT at 0.45 MPa°C99 (ISO 75, 0.45 MPa, Bambu Lab) against 87 for unfilled Bambu Lab ABS[2][21]Not documented
HDT at 1.8 MPa°C88 (ISO 75, 1.8 MPa, Bambu Lab) against 84 for unfilled Bambu Lab ABS[2][21]Not documented
Glass transition (Tg)°CNot documented60 (3DXTech AquaTek, DSC)[3]
Continuous service temperature°CNot documentedBounded by a glass transition of 60 °C[3]
Flammability / UL 94Not documentedFlammable; no UL 94 rating published[3]
Environment & Chemical
UV resistance1–5Not documentedDegrades within weeks outdoors, and dissolves in rain long before UV matters[4]
Chemical resistanceGood against weak acids, weak alkalis, oils and grease; dissolved by acetone[22]Dissolves in water; unusable in any wet or humid service environment[4][14]
Water / humidity resistance in service1–5Not documentedDissolves or disintegrates — by design[4][3]
Food contactNot food safe — Polymaker cites potential chemical leaching[17]Not offered as a food-contact material[3]
Biodegradability / compostabilityNot biodegradable[17]PVA is water-soluble and biodegrades in wastewater treatment, but Simplify3D notes disposal should follow local guidance[14]
RecyclabilityMechanically recyclable but not accepted in household plastic collection[17]Dissolved PVA goes to drain rather than to recycling[14]
Electrical & ESD propertiesNot documentedSurface resistance above 10^13 ohm/sq (ASTM D257, 3DXTech AquaTek PVA)[3]
Health & Safety
Fume toxicity1–5High — hazardous VOC such as styrene; enclosure and filtration needed[23][13]Low hazard — minimal VOC and particle emission; none of these materials was in the chamber study[23]
VOC emission rateµg/min12–113 styrene, the dominant VOC from every ABS and HIPS combination tested[23]Not documented
Ultrafine-particle emission rateparticles/min2 × 10¹⁰ to 9 × 10¹⁰ median across all ABS printers, two orders of magnitude above PLA's ≈1 × 10⁸[23]Not documented
Hazardous species emittedStyrene dominates. Bambu Lab states ABS and ASA release harmful gases such as styrene at printing temperature, which can be toxic and cause dizziness or nausea[23][13]Not documented
Ventilation / filtration requirement1–5Enclosure with carbon and HEPA filtration — an enclosure alone cut measured UFP by only about 35 %[23][13]Open a window / occasional ventilation[23]
Dust & fibre handling hazardGlass fibre is bound in the matrix; avoid inhaling sanding dust[1]Not documented
Post-Processing
Sanding & machiningSands well and takes filler before painting[17]Not sanded — it is dissolved away rather than finished[14]
Painting & finishingPaints readily after light abrasion[17]Not documented
Gluing & solvent weldingNot documentedNot applicable — PVA is a sacrificial support[14]
Vapour / chemical smoothingNot documentedWater is the solvent; no vapour smoothing is used[4]
Support material pairingHIPS breaks away or dissolves in d-limonene; Bambu Lab sells a dedicated Support for ABS[24][13]This is the support material; Polymaker pairs PolyDissolve S1 with PLA, TPU, PVB and PETG[4]
Dimensional accuracy & detailBambu Lab describes a smooth matte finish with micro-spot gloss that blurs layer lines[2]Not documented
Solvents & Solubility
Soluble inAcetone dissolves the resin and leaves the fibre as sludge; MEK, THF, ethyl acetate and chlorinated solvents do the same.[25][22]Water — tap water works cold, warm moving water is faster; 6–12 h typical, changing the water every few hours.[26][27]
Softened or crazed byPetrol and perchloroethylene soften it and benzene attacks it; d-limonene disrupts layer adhesion in some ABS and ASA grades.[25][28]Nothing else: polyvinyl alcohol resists organic solvents, so an IPA or acetone rinse leaves the support intact.[29]
Solvent welding & smoothing agentAcetone vapour reaches only the resin fraction, so the fibre is left standing proud of the smoothed surface.[30][22]None — water dissolves PVA rather than welding it, and no solvent gives it a smoothed surface.[26]

Material entries describe families or representative grades, not an interchangeable specification for every spool. Test methods, orientations and conditions may differ. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.

Sources for this comparison

  1. FibreX ABS+GF10 Glass Fiber ABS Technical Data Sheet 3DXTech · 2026-08 · tds
  2. Bambu Filament Technical Data Sheet V1.0 — ABS-GF Bambu Lab · 2026-08 · tds
  3. AquaTek PVA Water Soluble Support Technical Data Sheet v1.0 3DXTech · 2026-08 · tds
  4. PolyDissolve S1 Technical Data Sheet V5.4 Polymaker · 2024-11 · tds
  5. ABS-GF — product page Bambu Lab US Store · 2026-08 · vendor
  6. 3DXTech product catalogue 3DXTech · 2026-08 · vendor
  7. Siraya Tech Fibreheart ABS-GF Filament product page Siraya Tech · 2026-08 · vendor
  8. SUNLU ABS-GF (ABS Glass Fiber) 3D Printer Filament 1 kg SUNLU · 2026-08 · vendor
  9. Polymaker product catalogue Polymaker · 2026-08 · vendor
  10. YXPOLYER PVA 1 kg — product page YXPOLYER · 2026-08 · vendor
  11. IEMAI 3D E-WATER water-soluble support filament — store page IEMAI 3D · 2026-08 · vendor
  12. Reli3D PVA Filament 1.75 mm 500 g Natural — Amazon listing Amazon.com · 2026-08 · vendor
  13. ABS / ASA / PC Usage Guide Bambu Lab Wiki · 2026-08 · doc
  14. PVA — Ultimate 3D Printing Materials Guide Simplify3D · 2026-08 · doc
  15. ABS — Ultimate 3D Printing Materials Guide Simplify3D · 2026-08 · doc
  16. Max volumetric speed Prusa Knowledge Base · 2026-08 · doc
  17. ABS — material basics Polymaker Wiki · 2026-08 · doc
  18. Wet Filament — signs, causes and drying Polymaker Wiki · 2026-08 · doc
  19. FIBREX ABS+GF — product page (print recommendations) 3DXTech · 2026-08 · doc
  20. Composite materials filled with carbon, kevlar or glass Prusa Knowledge Base · 2026-08 · doc
  21. Bambu Filament Technical Data Sheet V3.0 — ABS Bambu Lab · 2026-08 · tds
  22. PolyLite ABS Technical Data Sheet (V5.5 served at this URL) Polymaker · 2024-11 · tds
  23. Emissions of Ultrafine Particles and Volatile Organic Compounds from Commercially Available Desktop Three-Dimensional Printers with Multiple Filaments (Azimi et al.) Environmental Science & Technology 50(3) 1260-1268 · 2016-01 · paper
  24. HIPS — Ultimate 3D Printing Materials Guide Simplify3D · 2026-08 · doc
  25. Chemical resistance — resistance of Ensinger plastics to chemicals (DIN 50 014, 23/50) Ensinger · 2026-08 · tds
  26. PolyDissolve S1 — Polymaker Wiki Polymaker · 2026-08 · doc
  27. 3DXTech AquaTek PVA product page 3DXTech · 2026-08 · vendor
  28. HIPS — Knowledge Base Prusa Research · 2026-08 · doc
  29. Polyvinyl alcohol — KURARAY POVAL application guide Kuraray · 2026-08 · tds
  30. Improve your 3D prints with chemical smoothing Prusa Research · 2026-08 · doc