3D Printing Info

Filament comparison

ABS-GF vs BVOH

Compare printing settings, strength, heat resistance, dated prices and sources.

Glass-fibre ABS (ABS-GF) guideBVOH (soluble support) guide

2 selected · all documented properties

Open these two in the interactive comparisonMore ABS-GF comparisonsMore BVOH comparisons
ABS-GF vs BVOH — documented properties and sources
PropertyGlass-fibre ABS (ABS-GF)ABSBVOH (soluble support)SUPPORT
Market snapshot
Listing priceUSD/kg; dated snapshots$34.99/kg median; $24.49–$73.33/kg across 4 dated product listings$165.72/kg median; $165.72–$165.72/kg across 1 dated product listings
Identity & Market
Base polymer / chemistryABS reinforced with chopped glass fibre — 3DXTech's grade is nominally 10 wt%[1][2]Butenediol vinyl alcohol copolymer — a vinyl alcohol copolymer that dissolves faster and in cooler water than straight PVA[3]
Densityg/cm³1.08 (Bambu Lab) and 1.15 (3DXTech), ISO 1183[2][1]Not documented
Typical priceUSD/kg1 kg-equivalent spools span 24–73; the middle of the market is about 35[4][5][6][7]1 kg-equivalent spools cluster near 166[3]
Price range across brandsUSD/kg24–73 across brands; Siraya Tech 24, Bambu Lab 30, SUNLU 40, 3DXTech 73[4][5][6][7]166 at Fiberlogy's 500 g pricing on 3DJake[3]
Market availability1–5Available from several mainstream brands[4][5]Niche, a handful of specialist brands[3]
Spool sizes & diameters1.75 and 2.85 mm; 750 g and 1 kg spools[5][4]1.75 and 2.85 mm; 0.5 kg spools[3]
Typical applicationsStiff, dimensionally stable enclosure and tooling parts; Bambu Lab notes the fibre blurs layer lines into a matte finish[2]Dissolvable support where PVA dissolves too slowly, and for materials PVA bonds to poorly[3]
Printing Parameters
Nozzle temperature°C240–280 (Bambu Lab)[2]Not documented
Bed temperature°C80–100 (Bambu Lab)[2]Not documented
Enclosure / chamber requirement1–5Enclosure recommended — Bambu Lab specifies a 45–60 °C chamber[2][8]Open frame is fine[9]
Recommended chamber temperature°C45–60 (Bambu Lab)[2]Not documented
Part cooling fan0–80 % (Bambu Lab)[2]Not documented
Bed surface & adhesion aidClean the plate and apply glue; Simplify3D also lists Kapton tape and ABS slurry[8][10]Not documented
Maximum volumetric flow (mm³/s; see test conditions)mm³/s14 at Bambu Lab's 180 mm/s cap on a 0.4 mm nozzle at 0.2 mm layer[2][11]Not documented
Warping tendency1–5Moderate — needs adhesion aid or draught shield; Bambu Lab positions the fibre as reducing warping[2]Not documented
Bed-adhesion difficulty1–5Needs a specific surface plus adhesive[8]Not documented
Stringing / oozing tendency1–5Slight — Polymaker advises 1–2 mm retraction at 20–30 mm/s[12]Not documented
Overall printing difficulty1–5Intermediate — dry filament and a tuned profile; hardened nozzle mandatory[8]Intermediate — dry filament and a tuned profile[13]
Extruder requirementNot documentedA second extruder or a tool changer[9]
Hardware Wear & Reliability
Nozzle hardness required1–4Hardened steel required[8]Brass fine indefinitely[9]
Abrasiveness1–5Highly abrasive — standard GF composite[8]Non-abrasive[9]
Nozzle clog risk1–5Moderate — needs dry filament and a clean nozzle; 3DXTech specifies a hardened 0.4 mm minimum nozzle and 0.25 mm layers or higher for the glass-filled grade[14][15]Very high — frequent jams without careful setup[13]
Heat-creep / jam sensitivity1–5Slightly sensitive[10]Not documented
Hotend requirementNo special hot-end required[10]Not documented
Moisture Behaviour
Moisture absorption (hygroscopicity)1–5Moderate — 0.53 % saturated at 25 °C / 55 % RH (Bambu Lab)[2]Very high (>2 %) — the vinyl alcohol backbone is what makes it soluble[13][9]
Equilibrium moisture content at ~50 % RH%0.53 saturated at 25 °C / 55 % RH (Bambu Lab)[2]Not documented
Drying temperature & time80 °C for 8 h (Bambu Lab)[2]Not documented
Symptoms when wetBubbling and popping at the nozzle, stringing and a rough surface[13]Not documented
Effect of moisture on strengthPolymaker rates ABS moderate-sensitivity and publishes no dry-versus-conditioned figures; absorbed water flashes to steam in the hotend and shows as bubbling and poor layer adhesion[13]Not a structural material; no dry-versus-conditioned data is published[13]
Storage requirementSealed with desiccant; Polymaker rates ABS moderate-sensitivity[13]Sealed with desiccant at all times[13]
Mechanical Properties
Tensile strength (XY)MPa36 ± 3 printed XY, ISO 527 (Bambu Lab); 3DXTech quotes 68 at break[2][1]Not documented
Young's modulusMPa3160 ± 170 printed XY, ISO 527 (Bambu Lab); 3DXTech quotes 4210[2][1]Not documented
Elongation at break%6.3 ± 1.2 printed XY, ISO 527 (Bambu Lab); 3DXTech quotes 2 at break[2][1]Not documented
Flexural strengthMPa68 ± 4 printed XY, ISO 178 (Bambu Lab); 3DXTech quotes 70[2][1]Not documented
Flexural modulusMPa2860 ± 130 printed XY, ISO 178 (Bambu Lab); 3DXTech quotes 4420[2][1]Not documented
Charpy impact, notchedkJ/m²4.2 ± 1.1 printed XY, ISO 179, notched (Bambu Lab)[2]Not documented
Other impact dataCharpy unnotched 14.5 ± 1.5 printed XY (Bambu Lab, ISO 179)[2]Not documented
Layer adhesion / Z tensileMPa29 ± 3 printed Z, ISO 527 (Bambu Lab)[2]Not documented
Brittleness1–5Brittle — snaps with little warning; notched Charpy falls from 21.5 to 4.2 kJ/m² against unfilled Bambu Lab ABS[2][16]Not documented
Creep resistance / sustained load1–5Good — no creep test found; chopped glass fibre lifts modulus to 3160 MPa against 2200 for unfilled Bambu Lab ABS[2][16]Not documented
Fatigue / repeated-flex resistance1–5Below average — no S-N curve found; notched Charpy falls to 4.2 kJ/m² against 21.5 for unfilled Bambu Lab ABS[2][16]Not documented
Elasticity / flexibility1–5Rigid[2]Not documented
Z strength as % of XY%81 (Bambu Lab, printed Z against XY tensile)[2]Not documented
Thermal Properties
HDT at 0.45 MPa°C99 (ISO 75, 0.45 MPa, Bambu Lab) against 87 for unfilled Bambu Lab ABS[2][16]Not documented
HDT at 1.8 MPa°C88 (ISO 75, 1.8 MPa, Bambu Lab) against 84 for unfilled Bambu Lab ABS[2][16]Not documented
Environment & Chemical
Chemical resistanceGood against weak acids, weak alkalis, oils and grease; dissolved by acetone[17]Not documented
Water / humidity resistance in service1–5Not documentedDissolves or disintegrates — by design[3]
Food contactNot food safe — Polymaker cites potential chemical leaching[12]Not documented
Biodegradability / compostabilityNot biodegradable[12]Not documented
RecyclabilityMechanically recyclable but not accepted in household plastic collection[12]Not documented
Health & Safety
Fume toxicity1–5High — hazardous VOC such as styrene; enclosure and filtration needed[18][8]Low hazard — minimal VOC and particle emission; none of these materials was in the chamber study[18]
VOC emission rateµg/min12–113 styrene, the dominant VOC from every ABS and HIPS combination tested[18]Not documented
Ultrafine-particle emission rateparticles/min2 × 10¹⁰ to 9 × 10¹⁰ median across all ABS printers, two orders of magnitude above PLA's ≈1 × 10⁸[18]Not documented
Hazardous species emittedStyrene dominates. Bambu Lab states ABS and ASA release harmful gases such as styrene at printing temperature, which can be toxic and cause dizziness or nausea[18][8]Not documented
Ventilation / filtration requirement1–5Enclosure with carbon and HEPA filtration — an enclosure alone cut measured UFP by only about 35 %[18][8]Open a window / occasional ventilation[18]
Dust & fibre handling hazardGlass fibre is bound in the matrix; avoid inhaling sanding dust[1]Not documented
Post-Processing
Sanding & machiningSands well and takes filler before painting[12]Not documented
Painting & finishingPaints readily after light abrasion[12]Not documented
Support material pairingHIPS breaks away or dissolves in d-limonene; Bambu Lab sells a dedicated Support for ABS[19][8]This is the support material[3]
Dimensional accuracy & detailBambu Lab describes a smooth matte finish with micro-spot gloss that blurs layer lines[2]Not documented
Solvents & Solubility
Soluble inAcetone dissolves the resin and leaves the fibre as sludge; MEK, THF, ethyl acetate and chlorinated solvents do the same.[20][17]Water: about 1 g of BVOH per 20 g of water, several hours; warmer water is faster but must not be too hot.[21][3]
Softened or crazed byPetrol and perchloroethylene soften it and benzene attacks it; d-limonene disrupts layer adhesion in some ABS and ASA grades.[20][22]Nothing else — a vinyl alcohol copolymer resists organic solvents, so IPA or acetone will not touch it.[23]
Solvent welding & smoothing agentAcetone vapour reaches only the resin fraction, so the fibre is left standing proud of the smoothed surface.[24][17]None — water is a removal solvent, not a welding one.[21]

Material entries describe families or representative grades, not an interchangeable specification for every spool. Test methods, orientations and conditions may differ. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.

Sources for this comparison

  1. FibreX ABS+GF10 Glass Fiber ABS Technical Data Sheet 3DXTech · 2026-08 · tds
  2. Bambu Filament Technical Data Sheet V1.0 — ABS-GF Bambu Lab · 2026-08 · tds
  3. Fiberlogy BVOH Natural — product page 3DJake International · 2026-08 · vendor
  4. ABS-GF — product page Bambu Lab US Store · 2026-08 · vendor
  5. 3DXTech product catalogue 3DXTech · 2026-08 · vendor
  6. Siraya Tech Fibreheart ABS-GF Filament product page Siraya Tech · 2026-08 · vendor
  7. SUNLU ABS-GF (ABS Glass Fiber) 3D Printer Filament 1 kg SUNLU · 2026-08 · vendor
  8. ABS / ASA / PC Usage Guide Bambu Lab Wiki · 2026-08 · doc
  9. PolyDissolve S1 Technical Data Sheet V5.4 Polymaker · 2024-11 · tds
  10. ABS — Ultimate 3D Printing Materials Guide Simplify3D · 2026-08 · doc
  11. Max volumetric speed Prusa Knowledge Base · 2026-08 · doc
  12. ABS — material basics Polymaker Wiki · 2026-08 · doc
  13. Wet Filament — signs, causes and drying Polymaker Wiki · 2026-08 · doc
  14. FIBREX ABS+GF — product page (print recommendations) 3DXTech · 2026-08 · doc
  15. Composite materials filled with carbon, kevlar or glass Prusa Knowledge Base · 2026-08 · doc
  16. Bambu Filament Technical Data Sheet V3.0 — ABS Bambu Lab · 2026-08 · tds
  17. PolyLite ABS Technical Data Sheet (V5.5 served at this URL) Polymaker · 2024-11 · tds
  18. Emissions of Ultrafine Particles and Volatile Organic Compounds from Commercially Available Desktop Three-Dimensional Printers with Multiple Filaments (Azimi et al.) Environmental Science & Technology 50(3) 1260-1268 · 2016-01 · paper
  19. HIPS — Ultimate 3D Printing Materials Guide Simplify3D · 2026-08 · doc
  20. Chemical resistance — resistance of Ensinger plastics to chemicals (DIN 50 014, 23/50) Ensinger · 2026-08 · tds
  21. Water soluble (BVOH/PVA) — Knowledge Base Prusa Research · 2026-08 · doc
  22. HIPS — Knowledge Base Prusa Research · 2026-08 · doc
  23. Polyvinyl alcohol — KURARAY POVAL application guide Kuraray · 2026-08 · tds
  24. Improve your 3D prints with chemical smoothing Prusa Research · 2026-08 · doc