3D Printing Info

Filament comparison

ABS-ESD vs TPE SEBS

Compare printing settings, strength, heat resistance, dated prices and sources.

ESD-safe ABS guideTPE (SEBS) guide

2 selected · all documented properties

Open these two in the interactive comparisonMore ABS-ESD comparisonsMore TPE SEBS comparisons
ABS-ESD vs TPE SEBS — documented properties and sources
PropertyESD-safe ABSABSTPE (SEBS)FLEX
Market snapshot
Listing priceUSD/kg; dated snapshots$102.50/kg median; $47.00–$166.67/kg across 4 dated product listings$98.25/kg median; $76.50–$120.00/kg across 2 dated product listings
Identity & Market
Base polymer / chemistryABS compounded with a conductive carbon filler for static-dissipative parts[1]Styrene-ethylene-butadiene-styrene thermoplastic elastomer — a styrenic rubber, not a polyurethane[2]
Densityg/cm³1.09 (ISO 1183)[1]1.044 printed part density (BASF Ultrafuse TPS 90A, ISO 1183-1) — the lightest elastomer here[2]
Typical priceUSD/kg1 kg-equivalent spools span 47–167; the middle of the market is about 103[3][4][5]1 kg-equivalent spools cluster near 77[6]
Price range across brandsUSD/kg47–167 across brands; IEMAI 47, YXPOLYER 65, 3DXTech 140 at 750 g pricing; the EMI-shielding ABS grade runs 167[3][4][5]77 for the Recreus 600 g spool; Proto-pasta only lists a 50 g coil, which prices at 120[6][7]
Market availability1–5Niche, a handful of specialist brands[3]Niche, a handful of specialist brands[2][7][6]
Spool sizes & diameters1.75 and 2.85 mm; 750 g spools[3]1.75 and 2.85 mm; 0.05 and 0.6 kg spools[2][6]
Typical applicationsElectronics handling fixtures, trays and jigs used around static-sensitive parts[1]Soft-touch overmoulds and skin-contact parts where a non-polyurethane elastomer is wanted[2]
Printing Parameters
Nozzle temperature°CNot documented260–280 (BASF Ultrafuse TPS 90A) — far hotter than any TPU here[2]
Bed temperature°CNot documented70–90 (BASF Ultrafuse TPS 90A)[2]
Enclosure / chamber requirement1–5Enclosure recommended[8]Open frame is fine[2]
Bed surface & adhesion aidClean the plate and apply glue; Simplify3D also lists Kapton tape and ABS slurry[8][9]PEI sheet or painter's tape; Polymaker warns TPU can over-stick and advises a glue stick as a release agent[10][11]
Maximum volumetric flow (mm³/s; see test conditions)mm³/sNot documented0.8–2.4 at the 10–30 mm/s BASF specifies on a 0.4 mm nozzle at 0.2 mm layer — the slowest material in this group[2]
Warping tendency1–5High — enclosure needed for reliable large parts[8]Not documented
Bed-adhesion difficulty1–5Needs a specific surface plus adhesive[8]Not documented
Stringing / oozing tendency1–5Slight — Polymaker advises 1–2 mm retraction at 20–30 mm/s[12]Not documented
Overall printing difficulty1–5Intermediate — dry filament and a tuned profile[8]Advanced — enclosure, hardware upgrades, tuning[2]
Extruder requirementNot documentedNozzle 0.4 mm or larger; BASF caps print speed at 10–30 mm/s[2]
Hardware Wear & Reliability
Nozzle hardness required1–4Hardened steel required[1]Brass fine indefinitely[13]
Abrasiveness1–5Moderately abrasive — conductive carbon filler[1]Non-abrasive[13]
Nozzle clog risk1–5Low — 3DXTech lists no special nozzle concerns and no minimum layer height for its ESD-ABS, only an 80 °C pre-dry[14]Moderate — needs dry filament and a clean nozzle; BASF caps print speed at 10–30 mm/s and Simplify3D warns that raised feed rates on flexibles most likely end in a jam[10][2]
Heat-creep / jam sensitivity1–5Slightly sensitive[9]Not documented
Hotend requirementNo special hot-end required[9]No special hot-end required, but a direct-drive extruder is (Simplify3D)[10]
Moisture Behaviour
Moisture absorption (hygroscopicity)1–5Moderate — the ABS matrix takes up 0.51–0.65 % saturated at 25 °C / 55 % RH and 3DXTech specifies a 80 °C, 4 h pre-dry[15][16][14]Negligible (<0.1 % EMC) — BASF states drying is not necessary, unique among the elastomers here[2]
Drying temperature & timeNot documentedNone — BASF states Ultrafuse TPS 90A arrives in a printable condition and drying is not necessary[2]
Symptoms when wetBubbling and popping at the nozzle, stringing and a rough surface[17]Bubbling and popping at the nozzle, stringing and a rough surface[17]
Effect of moisture on strengthPolymaker rates ABS moderate-sensitivity and publishes no dry-versus-conditioned figures; absorbed water flashes to steam in the hotend and shows as bubbling and poor layer adhesion[17]Not applicable — the SEBS chemistry has no amide or ester linkages to take up water, and BASF specifies no drying at all[2]
Storage requirementSealed with desiccant; Polymaker rates ABS moderate-sensitivity[17]Sealed with desiccant; often kept in a dryer during the print[17]
Mechanical Properties
Tensile strength (XY)MPa58 at break (printed XY, ISO 527) — the conductive filler raises strength above the unfilled grade's 42[1][18]Not documented
Young's modulusMPa2130 (printed XY, ISO 527)[1]Not documented
Elongation at break%4 at break (printed XY, ISO 527)[1]Not documented
Flexural strengthMPa80 (printed XY, ISO 178)[1]Not documented
Flexural modulusMPa2275 (printed XY, ISO 178)[1]Not documented
Brittleness1–5Moderate[1]Very ductile — bends far before failing[2]
Hardness (scale-specific)Shore A / Shore D / RockwellNot documented89 Shore A and 29 Shore D (BASF Ultrafuse TPS 90A, ISO 7619-1)[2]
Creep resistance / sustained load1–5Moderate — no creep test found; Tg of 105 °C keeps room-temperature service far below softening[1]Poor — no SEBS creep test; a printed 95A TPU bar crept from 74.5 to 82.7 mm over 5 days at 1.25 kg[19]
Fatigue / repeated-flex resistance1–5Below average — no S-N curve found; elongation at break 4 %, well below unfilled ABS[1][18]Excellent — living hinges viable[11]
Elasticity / flexibility1–5Rigid[1]Rubbery / highly elastic[2]
Wear resistance & frictionNot documentedAbrasion 111 mm³ (ISO 4649) — the poorest abrasion resistance in this group, well behind TPU[2]
Thermal Properties
Glass transition (Tg)°C105 (DSC)[1]Not documented
Melting point / Vicat°CNot documented242–249 melting (BASF Ultrafuse TPS 90A, ISO 11357-3)[2]
Environment & Chemical
UV resistance1–5Not documentedGood — years with some colour shift; Polymaker lists UV exposure among the conditions TPU withstands[11]
Chemical resistanceGood against weak acids, weak alkalis, oils and grease; dissolved by acetone[20]Withstands industrial solvents and UV exposure (Polymaker)[11]
Water / humidity resistance in service1–5Not documentedExcellent — essentially unaffected[2]
Food contactNot food safe — Polymaker cites potential chemical leaching[12]Not food safe without specific certification (Polymaker)[11]
Biodegradability / compostabilityNot biodegradable[12]Not biodegradable[11]
RecyclabilityMechanically recyclable but not accepted in household plastic collection[12]Not accepted in household plastic collection[11]
Electrical & ESD propertiesSurface resistance 10⁷–10⁹ ohm/sq, the static-dissipative band (ASTM D257), against above 10¹³ for unfilled ABS[1][18]Not documented
Health & Safety
Fume toxicity1–5High — hazardous VOC such as styrene; enclosure and filtration needed[21][8]Low hazard — minimal VOC and particle emission; TPU was not among the nine filaments in the chamber study[21]
VOC emission rateµg/min12–113 styrene, the dominant VOC from every ABS and HIPS combination tested[21]Not documented
Ultrafine-particle emission rateparticles/min2 × 10¹⁰ to 9 × 10¹⁰ median across all ABS printers, two orders of magnitude above PLA's ≈1 × 10⁸[21]Not documented
Hazardous species emittedStyrene dominates. Bambu Lab states ABS and ASA release harmful gases such as styrene at printing temperature, which can be toxic and cause dizziness or nausea[21][8]Not documented
Ventilation / filtration requirement1–5Enclosure with carbon and HEPA filtration — an enclosure alone cut measured UFP by only about 35 %[21][8]Open a window / occasional ventilation[21]
Dust & fibre handling hazardConductive carbon filler is bound in the matrix; avoid inhaling sanding dust[1]Not documented
Post-Processing
Sanding & machiningSands well and takes filler before painting[12]Difficult to sand or smooth; Polymaker limits post-processing to trimming or tumbling[11]
Painting & finishingPaints readily after light abrasion[12]Not documented
Gluing & solvent weldingNot documentedCyanoacrylate bonds TPU; no common solvent welds it[11]
Vapour / chemical smoothingNot documentedNo practical vapour smoothing[11]
Support material pairingHIPS breaks away or dissolves in d-limonene; Bambu Lab sells a dedicated Support for ABS[22][8]Polymaker warns TPU supports are often very difficult to remove[11]
Solvents & Solubility
Soluble inAcetone dissolves it — the basis of ABS slurry; so do MEK, THF, ethyl acetate, chloroform, dichloromethane and toluene.[23][20]Toluene dissolves SEBS at room temperature — Kraton quotes solution viscosity at 25 % mass in toluene, 25 °C.[24]
Softened or crazed byPetrol and perchloroethylene soften it and benzene attacks it; d-limonene disrupts layer adhesion in some ABS and ASA grades.[23][25]Soaking in hydrocarbon solvents and oils deteriorates it; short exposures are tolerated. Resists water, acids and bases.[24]
Solvent welding & smoothing agentAcetone: about 20 min of vapour at 80 °C over 5 mm of liquid. Prusa measured layer adhesion more than doubled.[26]Toluene will weld it, though the joint stays soft; no workshop-safe agent, and vapour smoothing is not practical.[24]

Material entries describe families or representative grades, not an interchangeable specification for every spool. Test methods, orientations and conditions may differ. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.

Sources for this comparison

  1. 3DXSTAT ESD-ABS Technical Data Sheet 3DXTech · 2026-08 · tds
  2. Ultrafuse TPS 90A Technical Data Sheet (Version 1.1, SEBS) BASF Forward AM · 2020-12 · tds
  3. 3DXTech product catalogue 3DXTech · 2026-08 · vendor
  4. IEMAI ESD-ABS 3D Printing Filament product page IEMAI 3D · 2026-08 · vendor
  5. YXPOLYER ABS ESD product page YXPOLYER · 2026-08 · vendor
  6. Recreus product catalogue Recreus · 2026-08 · vendor
  7. Proto-pasta product catalogue Proto-pasta · 2026-08 · vendor
  8. ABS / ASA / PC Usage Guide Bambu Lab Wiki · 2026-08 · doc
  9. ABS — Ultimate 3D Printing Materials Guide Simplify3D · 2026-08 · doc
  10. Flexible (TPE/TPU) — Ultimate 3D Printing Materials Guide Simplify3D · 2026-08 · doc
  11. TPU — material basics Polymaker Wiki · 2026-08 · doc
  12. ABS — material basics Polymaker Wiki · 2026-08 · doc
  13. Extrudr Product Catalogue (DURAPRO PA12 data block) Extrudr · 2025-03 · tds
  14. 3DXSTAT ESD-ABS — product page (print recommendations) 3DXTech · 2026-08 · doc
  15. Bambu Filament Technical Data Sheet V3.0 — ABS Bambu Lab · 2026-08 · tds
  16. Polymaker ABS Pro Technical Data Sheet V1 (2026-05-29) Polymaker · 2026-05 · tds
  17. Wet Filament — signs, causes and drying Polymaker Wiki · 2026-08 · doc
  18. 3DXMAX ABS Technical Data Sheet 3DXTech · 2026-08 · tds
  19. BambuLab TPU 95A HF vs Qidi TPU 95A HF — results spreadsheet My Tech Fun (Igor Gaspar) · 2024-02 · test
  20. PolyLite ABS Technical Data Sheet (V5.5 served at this URL) Polymaker · 2024-11 · tds
  21. Emissions of Ultrafine Particles and Volatile Organic Compounds from Commercially Available Desktop Three-Dimensional Printers with Multiple Filaments (Azimi et al.) Environmental Science & Technology 50(3) 1260-1268 · 2016-01 · paper
  22. HIPS — Ultimate 3D Printing Materials Guide Simplify3D · 2026-08 · doc
  23. Chemical resistance — resistance of Ensinger plastics to chemicals (DIN 50 014, 23/50) Ensinger · 2026-08 · tds
  24. KRATON polymers Grade Range — chemical resistance and toluene solution data Kraton Corporation · 2025-07 · tds
  25. HIPS — Knowledge Base Prusa Research · 2026-08 · doc
  26. Improve your 3D prints with chemical smoothing Prusa Research · 2026-08 · doc