3D Printing Info

Filament comparison

ABS-ESD vs PEEK

Compare printing settings, strength, heat resistance, dated prices and sources.

ESD-safe ABS guidePEEK guide

2 selected · all documented properties

Open these two in the interactive comparisonMore ABS-ESD comparisonsMore PEEK comparisons
ABS-ESD vs PEEK — documented properties and sources
PropertyESD-safe ABSABSPEEKHIGHTEMP
Market snapshot
Listing priceUSD/kg; dated snapshots$102.50/kg median; $47.00–$166.67/kg across 4 dated product listings$531.87/kg median; $296.14–$770.00/kg across 5 dated product listings
Identity & Market
Base polymer / chemistryABS compounded with a conductive carbon filler for static-dissipative parts[1]Polyether ether ketone — a semi-crystalline polyaryletherketone[2]
Densityg/cm³1.09 (ISO 1183)[1]1.30 (ISO 1183)[2][3]
Typical priceUSD/kg1 kg-equivalent spools span 47–167; the middle of the market is about 103[4][5][6]1 kg-equivalent spools span 296–770; the middle of the market is about 532[4][7][8]
Price range across brandsUSD/kg47–167 across brands; IEMAI 47, YXPOLYER 65, 3DXTech 140 at 750 g pricing; the EMI-shielding ABS grade runs 167[4][5][6]296-770 across brands and spool sizes; 3D4Makers recycled R-PEEK 296 at 750 g, IEMAI 3D 420 at 1 kg, LEHVOSS Luvocom 3F PEEK 9581 532 at 2 kg, 3DXTech ThermaX PEEK 770 at 500 g[4][7][8]
Market availability1–5Niche, a handful of specialist brands[4]Niche, a handful of specialist brands[4][7][3]
Spool sizes & diameters1.75 and 2.85 mm; 750 g spools[4]1.75 and 2.85 mm; 200 g to 2 kg spools[4][7][3]
Typical applicationsElectronics handling fixtures, trays and jigs used around static-sensitive parts[1]Aerospace brackets, semiconductor handling, sterilisable medical tooling and downhole parts[2]
Printing Parameters
Nozzle temperature°CNot documented380-400 (3DXTech printed-specimen conditions); Victrex quotes a 340-450 melt range for AM 450 FIL[2][3]
Bed temperature°CNot documented130–140 (3DXTech)[2]
Enclosure / chamber requirement1–5Enclosure recommended[9]Actively heated chamber required[10][11]
Recommended chamber temperature°CNot documentedNot less than 150 for semi-crystalline printing (Victrex AM 450 FIL); bed above 150[3]
Bed surface & adhesion aidClean the plate and apply glue; Simplify3D also lists Kapton tape and ABS slurry[9][12]Not documented
Warping tendency1–5High — enclosure needed for reliable large parts[9]Severe — heated chamber needed[10]
Bed-adhesion difficulty1–5Needs a specific surface plus adhesive[9]Very difficult — special plates or slurry required[10]
Stringing / oozing tendency1–5Slight — Polymaker advises 1–2 mm retraction at 20–30 mm/s[13]Not documented
Overall printing difficulty1–5Intermediate — dry filament and a tuned profile[9]Expert / industrial hardware only[10][11]
Extruder requirementNot documentedAn all-metal hot end rated above 400 °C and a heated chamber; 3DXTech tests at 0.25 mm layer height on a 0.4 mm nozzle[2][10]
Hardware Wear & Reliability
Nozzle hardness required1–4Hardened steel required[1]Brass fine indefinitely for unfilled grades, but brass softens near these nozzle temperatures — hardened or plated hot ends are the norm[10]
Abrasiveness1–5Moderately abrasive — conductive carbon filler[1]Non-abrasive when unfilled[2]
Nozzle clog risk1–5Low — 3DXTech lists no special nozzle concerns and no minimum layer height for its ESD-ABS, only an 80 °C pre-dry[14]Moderate — needs dry filament and a clean nozzle; 3DXTech lists no special nozzle concerns but a mandatory 120 °C pre-dry before every print[15]
Heat-creep / jam sensitivity1–5Slightly sensitive[12]Not documented
Hotend requirementNo special hot-end required[12]Not documented
Moisture Behaviour
Moisture absorption (hygroscopicity)1–5Moderate — the ABS matrix takes up 0.51–0.65 % saturated at 25 °C / 55 % RH and 3DXTech specifies a 80 °C, 4 h pre-dry[16][17][14]Not documented
Equilibrium moisture content at ~50 % RH%Not documented0.45 at saturation, 23 °C (ISO 62); 0.55 at 100 °C[3]
Drying temperature & timeNot documented120 °C for 5 h, target below 0.020 % moisture (Victrex AM 450 FIL)[3]
Symptoms when wetBubbling and popping at the nozzle, stringing and a rough surface[18]Not documented
Effect of moisture on strengthPolymaker rates ABS moderate-sensitivity and publishes no dry-versus-conditioned figures; absorbed water flashes to steam in the hotend and shows as bubbling and poor layer adhesion[18]No dry-versus-conditioned figures are published; 3DXTech mandates a 120 °C, 4 h pre-dry before every print because trapped water flashes to steam at these nozzle temperatures[15]
Storage requirementSealed with desiccant; Polymaker rates ABS moderate-sensitivity[18]Not documented
Mechanical Properties
Tensile strength (XY)MPa58 at break (printed XY, ISO 527) — the conductive filler raises strength above the unfilled grade's 42[1][19]60-100 (printed XY): Victrex AM 450 FIL 60-80 at yield and 3DXTech 100, both ISO 527; 98 at yield injection-moulded[2][3]
Young's modulusMPa2130 (printed XY, ISO 527)[1]3000-4000 (printed XY, ISO 527, Victrex AM 450 FIL); 3720 (3DXTech); 4000 injection-moulded[2][3]
Elongation at break%4 at break (printed XY, ISO 527)[1]28 (printed XY, ISO 527) — remarkably ductile for a high-temperature polymer[2]
Flexural strengthMPa80 (printed XY, ISO 178)[1]130 (printed XY, ISO 178)[2]
Flexural modulusMPa2275 (printed XY, ISO 178)[1]2700 (printed XY, ISO 178)[2]
Charpy impact, notchedkJ/m²Not documented6.0 (injection-moulded, ISO 179/1eA); unnotched does not break[3]
Other impact dataNot documentedIzod notched 7.0 kJ/m2 injection-moulded (ISO 180/A). Printed anisotropy is extreme: VICTREX AM 200 on a Stratasys F900 gives Izod notched 1380-1530 J/m XZ against 30-62 J/m ZX (ASTM D256)[3][20]
Layer adhesion / Z tensileMPaNot documented20-85 at yield (printed ZX, ISO 527, Victrex AM 450 FIL); the spread is set by chamber temperature and weld quality[3]
Brittleness1–5Moderate[1]Tough — absorbs impact, yields before breaking[2]
Hardness (scale-specific)Shore A / Shore D / RockwellNot documentedShore D 84.5 (injection-moulded, ISO 868); Rockwell M100 / R125 on extruded PEEK stock (ASTM D785)[3][21]
Creep resistance / sustained load1–5Moderate — no creep test found; Tg of 105 °C keeps room-temperature service far below softening[1]Excellent — holds load for years. Victrex rates PEEK for long-term creep; injection-moulded flexural stress at 3.5 % strain falls only from 125 MPa at 23 °C to 85 MPa at 125 °C, and extruded stock is rated to 249 °C continuous[22][3][21]
Fatigue / repeated-flex resistance1–5Below average — no S-N curve found; elongation at break 4 %, well below unfilled ABS[1][19]Excellent — living hinges viable. Victrex rates PEEK for long-term fatigue as well as creep[22]
Elasticity / flexibility1–5Rigid[1]Rigid[2]
Z strength as % of XY%Not documented71-84 (VICTREX AM 200 LMPAEK printed on the Stratasys F900 and Fortus 450mc, ZX against XZ tensile yield, ASTM D638); unfilled PEEK's own ZX spread is wider[20]
Thermal Properties
HDT at 0.45 MPa°CNot documented140 (printed XY, ISO 75 at 0.45 MPa, 3DXTech)[2]
HDT at 1.8 MPa°CNot documented152 (unannealed, ISO 75-2/Af, Victrex AM 450 FIL); 160 on extruded stock (ASTM D648 at 264 psi)[3][21]
Glass transition (Tg)°C105 (DSC)[1]143 (DSC, 3DXTech); Victrex gives onset 143 and midpoint 150 (ISO 11357-2)[2][3]
Melting point / Vicat°CNot documented343 melting (ISO 11357-3, Victrex); VICTREX AM 200 LMPAEK melts at 303[3][20]
Continuous service temperature°CNot documented240 UL 746B relative thermal index, strength (RTI electrical 260, impact 180); Ensinger rates extruded PEEK stock at 249 long term[3][21]
Thermal expansion (CTE)µm/m·KNot documented37.8 (extruded PEEK stock, 23-60 °C, ASTM E831; source states 2.1e-5 in/in/°F), rising to 41.9 at 60-100 °C and 55.8 at 100-150 °C[21]
Flammability / UL 94Not documentedUL 94 V-0 at 1.5 mm on the base resin; glow-wire flammability index 960 °C at 2.0 mm (IEC 60695-2-12)[2][3]
Environment & Chemical
Chemical resistanceGood against weak acids, weak alkalis, oils and grease; dissolved by acetone[23]Outstanding — resistant to almost all solvents and to steam sterilisation[2]
Water / humidity resistance in service1–5Not documentedExcellent — essentially unaffected; 0.45 % water at saturation and resistant to steam sterilisation[3][2]
Food contactNot food safe — Polymaker cites potential chemical leaching[13]Not documented
Biodegradability / compostabilityNot biodegradable[13]Not documented
RecyclabilityMechanically recyclable but not accepted in household plastic collection[13]Not documented
Electrical & ESD propertiesSurface resistance 10⁷–10⁹ ohm/sq, the static-dissipative band (ASTM D257), against above 10¹³ for unfilled ABS[1][19]Not documented
Health & Safety
Fume toxicity1–5High — hazardous VOC such as styrene; enclosure and filtration needed[24][9]Moderate — measurable VOCs and UFPs, ventilation advised. None of these polymers was in the chamber study, and all are processed far above the temperatures it covered[24]
VOC emission rateµg/min12–113 styrene, the dominant VOC from every ABS and HIPS combination tested[24]Not documented
Ultrafine-particle emission rateparticles/min2 × 10¹⁰ to 9 × 10¹⁰ median across all ABS printers, two orders of magnitude above PLA's ≈1 × 10⁸[24]Not documented
Hazardous species emittedStyrene dominates. Bambu Lab states ABS and ASA release harmful gases such as styrene at printing temperature, which can be toxic and cause dizziness or nausea[24][9]Not documented
Ventilation / filtration requirement1–5Enclosure with carbon and HEPA filtration — an enclosure alone cut measured UFP by only about 35 %[24][9]Ventilated room or enclosure recommended[24]
Dust & fibre handling hazardConductive carbon filler is bound in the matrix; avoid inhaling sanding dust[1]Not documented
Post-Processing
Sanding & machiningSands well and takes filler before painting[13]Not documented
Painting & finishingPaints readily after light abrasion[13]Not documented
Support material pairingHIPS breaks away or dissolves in d-limonene; Bambu Lab sells a dedicated Support for ABS[25][9]Not documented
Solvents & Solubility
Soluble inAcetone dissolves it — the basis of ABS slurry; so do MEK, THF, ethyl acetate, chloroform, dichloromethane and toluene.[26][23]95–98 wt% sulphuric acid dissolves it — 10 g per 100 mL at 40–70 °C gives a dark red solution. Laboratory route only.[27][26]
Softened or crazed byPetrol and perchloroethylene soften it and benzene attacks it; d-limonene disrupts layer adhesion in some ABS and ASA grades.[26][28]Concentrated nitric, hydrofluoric, hydrobromic and hydriodic acids attack it; DCM, DMSO and THF swell thin-walled sections.[29][26]
Solvent welding & smoothing agentAcetone: about 20 min of vapour at 80 °C over 5 mm of liquid. Prusa measured layer adhesion more than doubled.[30]None — no solvent softens PEEK, so parts are joined thermally or mechanically, never chemically.[29][26]

Material entries describe families or representative grades, not an interchangeable specification for every spool. Test methods, orientations and conditions may differ. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.

Sources for this comparison

  1. 3DXSTAT ESD-ABS Technical Data Sheet 3DXTech · 2026-08 · tds
  2. ThermaX PEEK Technical Data Sheet v3 3DXTech · 2026-08 · tds
  3. VICTREX AM 450 FIL — datasheet Victrex · 2025-12 · tds
  4. 3DXTech product catalogue 3DXTech · 2026-08 · vendor
  5. IEMAI ESD-ABS 3D Printing Filament product page IEMAI 3D · 2026-08 · vendor
  6. YXPOLYER ABS ESD product page YXPOLYER · 2026-08 · vendor
  7. 3D4Makers product catalogue 3D4Makers · 2026-08 · vendor
  8. IEMAI 3D PEEK 3D Printing Filament — store page IEMAI 3D · 2026-08 · vendor
  9. ABS / ASA / PC Usage Guide Bambu Lab Wiki · 2026-08 · doc
  10. Prusament PEI 1010 Technical Datasheet v1.0 Prusa Polymers · 2024-09 · tds
  11. Prusament PEI 1010 — material page Prusa Polymers · 2026-08 · doc
  12. ABS — Ultimate 3D Printing Materials Guide Simplify3D · 2026-08 · doc
  13. ABS — material basics Polymaker Wiki · 2026-08 · doc
  14. 3DXSTAT ESD-ABS — product page (print recommendations) 3DXTech · 2026-08 · doc
  15. ThermaX PEEK — product page 3DXTech · 2026-08 · vendor
  16. Bambu Filament Technical Data Sheet V3.0 — ABS Bambu Lab · 2026-08 · tds
  17. Polymaker ABS Pro Technical Data Sheet V1 (2026-05-29) Polymaker · 2026-05 · tds
  18. Wet Filament — signs, causes and drying Polymaker Wiki · 2026-08 · doc
  19. 3DXMAX ABS Technical Data Sheet 3DXTech · 2026-08 · tds
  20. VICTREX AM 200 — FDM Material Data Sheet Stratasys · 2024-04 · tds
  21. TECAPEEK natural (PEEK) — stock shape properties Ensinger · 2026-08 · tds
  22. PEEK polymers — product overview Victrex · 2026-08 · doc
  23. PolyLite ABS Technical Data Sheet (V5.5 served at this URL) Polymaker · 2024-11 · tds
  24. Emissions of Ultrafine Particles and Volatile Organic Compounds from Commercially Available Desktop Three-Dimensional Printers with Multiple Filaments (Azimi et al.) Environmental Science & Technology 50(3) 1260-1268 · 2016-01 · paper
  25. HIPS — Ultimate 3D Printing Materials Guide Simplify3D · 2026-08 · doc
  26. Chemical resistance — resistance of Ensinger plastics to chemicals (DIN 50 014, 23/50) Ensinger · 2026-08 · tds
  27. The Effects of Sulfonated Poly(ether ether ketone) Ion Exchange Preparation Conditions on Membrane Properties Yee, Zhang & Ladewig, Membranes 3(3) 182–195 · 2013-07 · paper
  28. HIPS — Knowledge Base Prusa Research · 2026-08 · doc
  29. What solvents are not compatible with PEEK? — fluidics technical FAQ IDEX Health & Science · 2026-08 · doc
  30. Improve your 3D prints with chemical smoothing Prusa Research · 2026-08 · doc