3D Printing Info

Filament comparison

ABS-CF vs TPU 85A

Compare printing settings, strength, heat resistance, dated prices and sources.

Carbon-fibre ABS (ABS-CF) guideTPU 85A guide

2 selected · all documented properties

Open these two in the interactive comparisonMore ABS-CF comparisonsMore TPU 85A comparisons
ABS-CF vs TPU 85A — documented properties and sources
PropertyCarbon-fibre ABS (ABS-CF)ABSTPU 85AFLEX
Market snapshot
Listing priceUSD/kg; dated snapshots$35.99/kg median; $22.00–$125.00/kg across 7 dated product listings$89.89/kg median; $31.99–$106.05/kg across 6 dated product listings
Identity & Market
Base polymer / chemistryABS reinforced with chopped carbon fibre[1]Soft thermoplastic polyurethane at 82–85 Shore A[2][3][4]
Densityg/cm³1.11 (ISO 1183)[1]1.11 (BASF Ultrafuse 85A) to 1.19 (NinjaFlex 85A), ISO 1183 / ASTM D792[4][2]
Typical priceUSD/kg1 kg-equivalent spools span 22–125; the middle of the market is about 36[5][6][7][8][9]1 kg-equivalent spools span 32–106; the middle of the market is about 90[5][10][2]
Price range across brandsUSD/kg22–125 across brands; IEMAI 22, Siraya Tech 28 and 36 for the core-shell grade, YXPOLYER 35, Push Plastic 50 at 2 kg, 3DXTech 64 at 750 g; Stratasys-compatible cartridges run far higher[5][6][7][8][11][9]32–106 across brands; Siraya Tech Flex TPU 85A 32 at 1 kg, add:north TPU Pro Matte 85A 72, Recreus Filaflex 82A 90 at 500 g, Proto-pasta Clear Flexible TPU 90, 3DXTech 3DXFLEX 85A 96, NinjaTek NinjaFlex 106[12][5][10][13][2]
Market availability1–5Available from several mainstream brands[5][6]Available from several mainstream brands[5][12]
Spool sizes & diameters1.75 and 2.85 mm; 0.5, 0.75 and 2 kg spools plus Stratasys-compatible cartridges[5][6]1.75, 2.85 and 3 mm; 0.5, 1 and 2 kg spools[5][12][2]
Typical applicationsStiff tooling and fixtures that must survive above 100 °C[1]Soft-touch grips, seals, wearables and anything that must compress and rebound[2][3]
Printing Parameters
Nozzle temperature°CNot documented200–220 (BASF Ultrafuse 85A, 210 typical)[4]
Bed temperature°CNot documented40 (BASF Ultrafuse 85A)[4]
Enclosure / chamber requirement1–5Enclosure recommended[14]Open frame is fine[4]
Bed surface & adhesion aidClean the plate and apply glue; Simplify3D also lists Kapton tape and ABS slurry[14][15]PEI sheet or painter's tape; Polymaker warns TPU can over-stick and advises a glue stick as a release agent[16][17]
Maximum volumetric flow (mm³/s; see test conditions)mm³/sNot documented1.2–3.2 at the 15–40 mm/s BASF specifies on a 0.4 mm nozzle at 0.2 mm layer[4]
Warping tendency1–5Moderate — needs adhesion aid or draught shield; the fibre reduces warping against unfilled ABS[14]None[4]
Bed-adhesion difficulty1–5Needs a specific surface plus adhesive[14]Sticks to anything — Recreus states its 82A grade has excellent bed adhesion without a heated bed or additives[3]
Stringing / oozing tendency1–5Slight — Polymaker advises 1–2 mm retraction at 20–30 mm/s[18]High — drying plus tuning needed[19][17]
Overall printing difficulty1–5Intermediate — dry filament and a tuned profile; hardened nozzle mandatory[14]Advanced — enclosure, hardware upgrades, tuning; at this hardness the filament will not push through a Bowden tube[2][3]
Extruder requirementNot documentedDirect drive only. NinjaTek calls its 85A grade ideal for direct-drive extruders and Recreus specifies direct-drive printers for 82A; BASF caps print speed at 15–40 mm/s with a nozzle of 0.4 mm or larger[2][3][4]
Hardware Wear & Reliability
Nozzle hardness required1–4Hardened steel required[14]Brass fine indefinitely[20]
Abrasiveness1–5Highly abrasive — standard CF composite[14]Non-abrasive[20]
Nozzle clog risk1–5Moderate — needs dry filament and a clean nozzle; 3DXTech specifies a hardened nozzle of 0.4 mm minimum and 0.25 mm layers or higher, and Prusa lists composites as a higher clogging risk[21][22][23]High — jams from moisture, heat creep or particles[19][17]
Heat-creep / jam sensitivity1–5Slightly sensitive[15]Very high — softens in the cold zone readily; soft filament buckles between the drive gear and the melt zone[17][2]
Hotend requirementNo special hot-end required[15]No special hot-end required, but a direct-drive extruder is (Simplify3D)[16]
Moisture Behaviour
Moisture absorption (hygroscopicity)1–5Moderate — the ABS matrix takes up 0.51–0.65 % saturated at 25 °C / 55 % RH and 3DXTech specifies a 80 °C, 4 h pre-dry[24][25][21]Moderate — NinjaTek measures 0.22 % in 24 h (ASTM D570) and BASF specifies a 70 °C dry for at least 5 h[2][4]
Equilibrium moisture content at ~50 % RH%Not documented0.22 after 24 h water immersion (NinjaFlex 85A, ASTM D570) — an immersion figure, not an equilibrium moisture content at 50 % RH[2]
Drying temperature & timeNot documented70 °C for at least 5 h in a hot-air dryer or vacuum oven (BASF)[4]
Symptoms when wetBubbling and popping at the nozzle, stringing and a rough surface[19]Bubbling and popping at the nozzle, stringing and a rough surface[19]
Effect of moisture on strengthPolymaker rates ABS moderate-sensitivity and publishes no dry-versus-conditioned figures; absorbed water flashes to steam in the hotend and shows as bubbling and poor layer adhesion[19]Polymaker groups TPU with the highly hygroscopic materials; wet TPU prints with poor layer adhesion and weak, brittle layers[19]
Storage requirementSealed with desiccant; Polymaker rates ABS moderate-sensitivity[19]Sealed with desiccant; often kept in a dryer during the print[19]
Mechanical Properties
Tensile strength (XY)MPa46 at break (printed XY, ISO 527)[1]26 ultimate (NinjaFlex 85A, ASTM D638)[2]
Young's modulusMPa5210 (printed XY, ISO 527) — more than double unfilled ABS[1]12 (NinjaFlex 85A, ASTM D638) — two orders of magnitude below any rigid filament; NinjaTek's 95A Cheetah reaches 26 by the same method[2][26]
Elongation at break%2 at break (printed XY, ISO 527)[1]650 at break (Filaflex 82A) and 660 (NinjaFlex 85A); BASF measures 600 in XY and 320 in ZX[3][2][4]
Flexural strengthMPa76 (printed XY, ISO 178)[1]Not documented
Flexural modulusMPa5260 (printed XY, ISO 178)[1]Not documented
Brittleness1–5Brittle — snaps with little warning; elongation at break 2 %[1]Very ductile — bends far before failing[2]
Hardness (scale-specific)Shore A / Shore D / RockwellNot documented29 Shore D / 85 Shore A (BASF Ultrafuse 85A, ISO 7619-1); 85 Shore A (NinjaFlex, ASTM D2240); 82 A nominal for Filaflex[2][4][3]
Creep resistance / sustained load1–5Good — no creep test found; chopped carbon fibre restrains matrix flow and modulus rises to 5210 MPa against 2200–2330 for unfilled ABS[1][24][25]Poor — no 85A creep test; a printed 95A TPU bar crept from 74.5 to 82.7 mm over 5 days at 1.25 kg, and softer grades creep more[27]
Fatigue / repeated-flex resistance1–5Below average — no S-N curve found; elongation at break falls to 2 % against 10.5 % for unfilled ABS[1][24]Excellent — living hinges viable[17]
Elasticity / flexibility1–5Rigid[1]Rubbery / highly elastic[2][3]
Z strength as % of XY%Not documented53 — BASF measures 320 % elongation at break in ZX against 600 % in XY[4]
Wear resistance & frictionNot documentedAbrasion 0.08 g mass loss over 10 000 cycles (NinjaFlex, ASTM D4060); 82 mm³ (BASF, ISO 4649)[2][4]
Thermal Properties
Glass transition (Tg)°C105 (DSC)[1]Not documented
Melting point / Vicat°CNot documented216 melting (NinjaFlex 85A, DSC)[2]
Thermal expansion (CTE)µm/m·K19–25 along the print bead and 80–84 in the build direction at 30 °C (20 wt% CF, large-format printed, TMA)[28]Not documented
Environment & Chemical
UV resistance1–5Not documentedGood — years with some colour shift; Polymaker lists UV exposure among the conditions TPU withstands[17]
Chemical resistanceGood against weak acids, weak alkalis, oils and grease; dissolved by acetone[29]Withstands industrial solvents and UV exposure (Polymaker)[17]
Food contactNot food safe — Polymaker cites potential chemical leaching[18]Not food safe without specific certification (Polymaker)[17]
Biodegradability / compostabilityNot biodegradable[18]Not biodegradable[17]
RecyclabilityMechanically recyclable but not accepted in household plastic collection[18]Not accepted in household plastic collection[17]
Electrical & ESD propertiesSurface resistance above 10⁹ ohm/sq — not static-dissipative (ASTM D257)[1]Not documented
Health & Safety
Fume toxicity1–5High — hazardous VOC such as styrene; enclosure and filtration needed[30][14]Low hazard — minimal VOC and particle emission; TPU was not among the nine filaments in the chamber study[30]
VOC emission rateµg/min12–113 styrene, the dominant VOC from every ABS and HIPS combination tested[30]Not documented
Ultrafine-particle emission rateparticles/min2 × 10¹⁰ to 9 × 10¹⁰ median across all ABS printers, two orders of magnitude above PLA's ≈1 × 10⁸[30]Not documented
Hazardous species emittedStyrene dominates. Bambu Lab states ABS and ASA release harmful gases such as styrene at printing temperature, which can be toxic and cause dizziness or nausea[30][14]Not documented
Ventilation / filtration requirement1–5Enclosure with carbon and HEPA filtration — an enclosure alone cut measured UFP by only about 35 %[30][14]Open a window / occasional ventilation[30]
Dust & fibre handling hazardCarbon fibre is bound in the matrix; sanding dust should not be inhaled[1]Not documented
Post-Processing
Sanding & machiningSands well and takes filler before painting[18]Difficult to sand or smooth; Polymaker limits post-processing to trimming or tumbling[17]
Painting & finishingPaints readily after light abrasion[18]Not documented
Gluing & solvent weldingNot documentedCyanoacrylate bonds TPU; no common solvent welds it[17]
Vapour / chemical smoothingAcetone smoothing is blunted by the fibre — only the resin fraction dissolves[29]No practical vapour smoothing[17]
Support material pairingHIPS breaks away or dissolves in d-limonene; Bambu Lab sells a dedicated Support for ABS[31][14]Polymaker warns TPU supports are often very difficult to remove[17]
Solvents & Solubility
Soluble inAcetone dissolves the resin and leaves the fibre as sludge; MEK, THF, ethyl acetate and chlorinated solvents do the same.[32][29]DMF, DMSO, NMP and THF dissolve TPU; acetone, MEK and cyclohexanone are partial solvents. All laboratory reagents.[33]
Softened or crazed byPetrol and perchloroethylene soften it and benzene attacks it; d-limonene disrupts layer adhesion in some ABS and ASA grades.[32][34]Toluene and benzene swell it up to +50 % by weight at 23 °C; esters swell it severely; ethanol and IPA soften it.[33]
Solvent welding & smoothing agentAcetone vapour reaches only the resin fraction, so the fibre is left standing proud of the smoothed surface.[35][29]None practical — the true solvents (DMF, THF, NMP) are laboratory reagents and leave the joint swollen and weak.[33]

Material entries describe families or representative grades, not an interchangeable specification for every spool. Test methods, orientations and conditions may differ. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.

Sources for this comparison

  1. CarbonX Carbon Fiber ABS Technical Data Sheet 3DXTech · 2026-08 · tds
  2. NinjaFlex 85A Technical Specifications NinjaTek · 2026-08 · tds
  3. Filaflex 82A product page (Shore hardness and elongation) Recreus · 2026-08 · vendor
  4. Ultrafuse TPU 85A Technical Data Sheet (Version 3.0) BASF Forward AM · 2022-08 · tds
  5. 3DXTech product catalogue 3DXTech · 2026-08 · vendor
  6. Push Plastic product catalogue Push Plastic · 2026-08 · vendor
  7. IEMAI CF-ABS 3D Printing Filament product page IEMAI 3D · 2026-08 · vendor
  8. Siraya Tech Fibreheart ABS-CF Filament product page Siraya Tech · 2026-08 · vendor
  9. YXPOLYER ABS CF product page YXPOLYER · 2026-08 · vendor
  10. Siraya Tech Flex TPU 85A Filament — product page Siraya Tech · 2026-08 · vendor
  11. Siraya Tech Fibreheart ABS-CF Core Filament product page Siraya Tech · 2026-08 · vendor
  12. Proto-pasta product catalogue Proto-pasta · 2026-08 · vendor
  13. add:north TPU Pro Matte 85A product page add:north · 2026-08 · vendor
  14. ABS / ASA / PC Usage Guide Bambu Lab Wiki · 2026-08 · doc
  15. ABS — Ultimate 3D Printing Materials Guide Simplify3D · 2026-08 · doc
  16. Flexible (TPE/TPU) — Ultimate 3D Printing Materials Guide Simplify3D · 2026-08 · doc
  17. TPU — material basics Polymaker Wiki · 2026-08 · doc
  18. ABS — material basics Polymaker Wiki · 2026-08 · doc
  19. Wet Filament — signs, causes and drying Polymaker Wiki · 2026-08 · doc
  20. Extrudr Product Catalogue (DURAPRO PA12 data block) Extrudr · 2025-03 · tds
  21. CARBONX ABS+CF — product page (print recommendations) 3DXTech · 2026-08 · doc
  22. Composite materials filled with carbon, kevlar or glass Prusa Knowledge Base · 2026-08 · doc
  23. Carbon Fiber Filled — Ultimate 3D Printing Materials Guide Simplify3D · 2026-08 · doc
  24. Bambu Filament Technical Data Sheet V3.0 — ABS Bambu Lab · 2026-08 · tds
  25. Polymaker ABS Pro Technical Data Sheet V1 (2026-05-29) Polymaker · 2026-05 · tds
  26. NinjaTek technical specs comparison chart (Cheetah, NinjaFlex, Armadillo, Alloy 910, Nylon 645) NinjaTek · 2026-08 · tds
  27. BambuLab TPU 95A HF vs Qidi TPU 95A HF — results spreadsheet My Tech Fun (Igor Gaspar) · 2024-02 · test
  28. Effects of Fiber Orientation on the Coefficient of Thermal Expansion of Fiber-Filled Polymer Systems in Large Format Polymer Extrusion-Based Additive Manufacturing Materials 15(8):2764 · 2022-04 · paper
  29. PolyLite ABS Technical Data Sheet (V5.5 served at this URL) Polymaker · 2024-11 · tds
  30. Emissions of Ultrafine Particles and Volatile Organic Compounds from Commercially Available Desktop Three-Dimensional Printers with Multiple Filaments (Azimi et al.) Environmental Science & Technology 50(3) 1260-1268 · 2016-01 · paper
  31. HIPS — Ultimate 3D Printing Materials Guide Simplify3D · 2026-08 · doc
  32. Chemical resistance — resistance of Ensinger plastics to chemicals (DIN 50 014, 23/50) Ensinger · 2026-08 · tds
  33. Elastollan — Chemical properties: swelling and chemical resistance BASF · 2026-08 · tds
  34. HIPS — Knowledge Base Prusa Research · 2026-08 · doc
  35. Improve your 3D prints with chemical smoothing Prusa Research · 2026-08 · doc