3D Printing Info

Filament comparison

ABS-CF vs PETG-ESD

Compare printing settings, strength, heat resistance, dated prices and sources.

Carbon-fibre ABS (ABS-CF) guideESD-safe PETG guide

2 selected · all documented properties

Open these two in the interactive comparisonMore ABS-CF comparisonsMore PETG-ESD comparisons
ABS-CF vs PETG-ESD — documented properties and sources
PropertyCarbon-fibre ABS (ABS-CF)ABSESD-safe PETGPETG
Market snapshot
Listing priceUSD/kg; dated snapshots$35.99/kg median; $22.00–$125.00/kg across 7 dated product listings$102.99/kg median; $65.98–$140.00/kg across 2 dated product listings
Identity & Market
Base polymer / chemistryABS reinforced with chopped carbon fibre[1]PETG compounded with a conductive filler to bring surface resistivity into the static-dissipative range[2][3]
Densityg/cm³1.11 (ISO 1183)[1]1.24 (Fiberon) and 1.28 (3DXTech), ISO 1183[2][3]
Typical priceUSD/kg1 kg-equivalent spools span 22–125; the middle of the market is about 36[4][5][6][7][8]1 kg-equivalent spools span 66–140; the middle of the market is about 103[9][4]
Price range across brandsUSD/kg22–125 across brands; IEMAI 22, Siraya Tech 28 and 36 for the core-shell grade, YXPOLYER 35, Push Plastic 50 at 2 kg, 3DXTech 64 at 750 g; Stratasys-compatible cartridges run far higher[4][5][6][7][10][8]66–140 across brands; Fiberon PETG-ESD 66, 3DXSTAT ESD-PETG 140[9][4]
Market availability1–5Available from several mainstream brands[4][5]Niche, a handful of specialist brands[9][4]
Spool sizes & diameters1.75 and 2.85 mm; 0.5, 0.75 and 2 kg spools plus Stratasys-compatible cartridges[4][5]1.75 mm; 0.5, 0.75, 1 and 3 kg spools[9][4]
Typical applicationsStiff tooling and fixtures that must survive above 100 °C[1]Electronics fixtures, trays and jigs handled around static-sensitive components[2][3]
Printing Parameters
Nozzle temperature°CNot documented250–290 (Fiberon)[2]
Bed temperature°CNot documented70–80 (Fiberon); 70 (3DXTech)[2][3]
Enclosure / chamber requirement1–5Enclosure recommended[11]Open frame is fine — Fiberon specifies room-temperature chamber[2]
Bed surface & adhesion aidClean the plate and apply glue; Simplify3D also lists Kapton tape and ABS slurry[11][12]Textured PEI, satin or powder-coated sheets; on smooth PEI a glue stick acts as a release agent[13][14]
Maximum volumetric flow (mm³/s; see test conditions)mm³/sNot documentedFiberon rates the material to 500 mm/s, equivalent to 40 on a 0.4 mm nozzle at 0.2 mm layer — a machine-limited headline rather than a measured melt rate[2][15]
Warping tendency1–5Moderate — needs adhesion aid or draught shield; the fibre reduces warping against unfilled ABS[11]Not documented
Bed-adhesion difficulty1–5Needs a specific surface plus adhesive[11]Needs the right surface or a thin adhesive — the problem is releasing the part, not sticking it[13][14]
Stringing / oozing tendency1–5Slight — Polymaker advises 1–2 mm retraction at 20–30 mm/s[16]Moderate — retraction tuning needed; Polymaker names stringing as PETG's common quirk[14]
Overall printing difficulty1–5Intermediate — dry filament and a tuned profile; hardened nozzle mandatory[11]Intermediate — dry filament and a tuned profile; resistivity depends on getting the nozzle temperature right[2]
Hardware Wear & Reliability
Nozzle hardness required1–4Hardened steel required[11]Hardened steel required[2]
Abrasiveness1–5Highly abrasive — standard CF composite[11]Moderately abrasive — conductive carbon filler[2]
Nozzle clog risk1–5Moderate — needs dry filament and a clean nozzle; 3DXTech specifies a hardened nozzle of 0.4 mm minimum and 0.25 mm layers or higher, and Prusa lists composites as a higher clogging risk[17][18][19]Low — 3DXTech lists no special nozzle concerns and no minimum layer height for its ESD-PETG, only a 65 °C pre-dry[20]
Heat-creep / jam sensitivity1–5Slightly sensitive[12]Slightly sensitive[21]
Hotend requirementNo special hot-end required[12]No special hot-end required[21]
Moisture Behaviour
Moisture absorption (hygroscopicity)1–5Moderate — the ABS matrix takes up 0.51–0.65 % saturated at 25 °C / 55 % RH and 3DXTech specifies a 80 °C, 4 h pre-dry[22][23][17]Moderate (0.3–0.8 %) — the PETG matrix reaches 0.40 % saturated at 25 °C / 55 % RH and 3DXTech specifies a 65 °C, 4 h pre-dry[13][20]
Equilibrium moisture content at ~50 % RH%Not documented0.41 equilibrium water absorption (Fiberon PETG-ESD)[2]
Drying temperature & timeNot documented65 °C for 3 h (Fiberon)[2]
Symptoms when wetBubbling and popping at the nozzle, stringing and a rough surface[24]Bubbling and popping at the nozzle, stringing and a rough surface[24]
Effect of moisture on strengthPolymaker rates ABS moderate-sensitivity and publishes no dry-versus-conditioned figures; absorbed water flashes to steam in the hotend and shows as bubbling and poor layer adhesion[24]Polymaker groups PETG with nylon, PVA and TPU as highly hygroscopic; no dry-versus-conditioned strength figures are published for this grade and the loss shows as bubbling and poor layer adhesion[24]
Storage requirementSealed with desiccant; Polymaker rates ABS moderate-sensitivity[24]Sealed with desiccant; Polymaker groups PETG with the highly hygroscopic materials[24][14]
Mechanical Properties
Tensile strength (XY)MPa46 at break (printed XY, ISO 527)[1]36.1 ± 0.9 printed XY, ISO 527 (Fiberon); 3DXTech quotes 50 at break[2][3]
Young's modulusMPa5210 (printed XY, ISO 527) — more than double unfilled ABS[1]1983 ± 75 printed XY, ISO 527 (Fiberon)[2]
Elongation at break%2 at break (printed XY, ISO 527)[1]7.3 ± 0.7 printed XY, ISO 527 (Fiberon); 3DXTech quotes 13 at break[2][3]
Flexural strengthMPa76 (printed XY, ISO 178)[1]54.0 ± 2.5 printed XY, ISO 178 (Fiberon)[2]
Flexural modulusMPa5260 (printed XY, ISO 178)[1]1651 ± 141 printed XY, ISO 178 (Fiberon)[2]
Charpy impact, notchedkJ/m²Not documented5.7 ± 0.5 printed XY, ISO 179, notched (Fiberon)[2]
Other impact dataNot documentedCharpy unnotched 29.3 ± 2.2 printed XY (Fiberon, ISO 179)[2]
Layer adhesion / Z tensileMPaNot documented20.7 ± 0.6 printed Z, ISO 527 (Fiberon)[2]
Brittleness1–5Brittle — snaps with little warning; elongation at break 2 %[1]Moderate[2]
Creep resistance / sustained load1–5Good — no creep test found; chopped carbon fibre restrains matrix flow and modulus rises to 5210 MPa against 2200–2330 for unfilled ABS[1][22][23]Below average — no ESD-grade creep test; unfilled PETG sagged from 12 to 17.1–20.4 mm over 5 days at 1.25 kg[25][26][27][28]
Fatigue / repeated-flex resistance1–5Below average — no S-N curve found; elongation at break falls to 2 % against 10.5 % for unfilled ABS[1][22]Moderate — no ESD-grade S-N curve; unfilled printed PETG ran 79 000–193 000 cycles at 30 % of tensile strength[29]
Elasticity / flexibility1–5Rigid[1]Slightly flexible in thin sections[2]
Z strength as % of XY%Not documented57 (Fiberon, printed Z against XY tensile)[2]
Thermal Properties
HDT at 0.45 MPa°CNot documented76 (ISO 75, 0.45 MPa, Fiberon)[2]
HDT at 1.8 MPa°CNot documented72 (ISO 75, 1.8 MPa, Fiberon)[2]
Glass transition (Tg)°C105 (DSC)[1]77 (Fiberon) and 80 (3DXTech), DSC[2][3]
Melting point / Vicat°CNot documentedAmorphous — no melting point; Vicat 86 (Fiberon, ISO 306)[2]
Thermal expansion (CTE)µm/m·K19–25 along the print bead and 80–84 in the build direction at 30 °C (20 wt% CF, large-format printed, TMA)[30]Not documented
Flammability / UL 94Not documentedFlammable; no UL 94 rating published for standard grades[31]
Environment & Chemical
Chemical resistanceGood against weak acids, weak alkalis, oils and grease; dissolved by acetone[32]Withstands acids, alkalis, oils and UV exposure[14]
Food contactNot food safe — Polymaker cites potential chemical leaching[16]Not certified for food contact as filament[14]
Biodegradability / compostabilityNot biodegradable[16]Not biodegradable[14]
RecyclabilityMechanically recyclable but not accepted in household plastic collection[16]Not accepted in household plastic collection[14]
Electrical & ESD propertiesSurface resistance above 10⁹ ohm/sq — not static-dissipative (ASTM D257)[1]Surface resistivity falls with nozzle temperature: 7.0×10⁶–1.6×10⁷ ohm at 250 °C, 3.2×10⁵–4.7×10⁵ at 270 °C and below 1×10⁴ at 290 °C (Fiberon); 3DXTech quotes 10⁷–10⁹ ohm/sq[2][3]
Health & Safety
Fume toxicity1–5High — hazardous VOC such as styrene; enclosure and filtration needed[33][11]Moderate — measurable VOCs and UFPs, ventilation advised[33]
VOC emission rateµg/min12–113 styrene, the dominant VOC from every ABS and HIPS combination tested[33]Not documented
Ultrafine-particle emission rateparticles/min2 × 10¹⁰ to 9 × 10¹⁰ median across all ABS printers, two orders of magnitude above PLA's ≈1 × 10⁸[33]Not documented
Hazardous species emittedStyrene dominates. Bambu Lab states ABS and ASA release harmful gases such as styrene at printing temperature, which can be toxic and cause dizziness or nausea[33][11]Not documented
Ventilation / filtration requirement1–5Enclosure with carbon and HEPA filtration — an enclosure alone cut measured UFP by only about 35 %[33][11]Open a window / occasional ventilation[33]
Dust & fibre handling hazardCarbon fibre is bound in the matrix; sanding dust should not be inhaled[1]Conductive carbon filler is bound in the matrix; avoid inhaling sanding dust[2]
Post-Processing
Sanding & machiningSands well and takes filler before painting[16]Sands poorly — the material is tough and gums rather than powders[21]
Painting & finishingPaints readily after light abrasion[16]Not documented
Gluing & solvent weldingNot documentedCyanoacrylate; no common solvent welds PETG cleanly[21]
Vapour / chemical smoothingAcetone smoothing is blunted by the fibre — only the resin fraction dissolves[32]No practical vapour smoothing[21]
Support material pairingHIPS breaks away or dissolves in d-limonene; Bambu Lab sells a dedicated Support for ABS[34][11]Prints its own supports; Polymaker rates PolyDissolve S1 for PETG[21]
Dimensional accuracy & detailNot documentedNozzle temperature has to be held steady — it moves surface resistivity by three orders of magnitude[2]
Solvents & Solubility
Soluble inAcetone dissolves the resin and leaves the fibre as sludge; MEK, THF, ethyl acetate and chlorinated solvents do the same.[35][32]No common workshop solvent; 1,2-dichloroethane destroys it inside a week and dichloromethane — a carcinogen — dissolves the surface.[36][37]
Softened or crazed byPetrol and perchloroethylene soften it and benzene attacks it; d-limonene disrupts layer adhesion in some ABS and ASA grades.[35][38]Acetone (+16 % weight over 1 year at 23 °C), ethyl acetate, toluene and DMF swell and soften it; methanol crazes it.[36]
Solvent welding & smoothing agentAcetone vapour reaches only the resin fraction, so the fibre is left standing proud of the smoothed surface.[37][32]Dichloromethane brushed on is the only agent that smooths PETG — a controlled carcinogen, not workshop stock.[37]

Material entries describe families or representative grades, not an interchangeable specification for every spool. Test methods, orientations and conditions may differ. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.

Sources for this comparison

  1. CarbonX Carbon Fiber ABS Technical Data Sheet 3DXTech · 2026-08 · tds
  2. Fiberon PETG-ESD Technical Data Sheet V1.1 Polymaker · 2026-08 · tds
  3. 3DXSTAT ESD-PETG Technical Data Sheet 3DXTech · 2026-08 · tds
  4. 3DXTech product catalogue 3DXTech · 2026-08 · vendor
  5. Push Plastic product catalogue Push Plastic · 2026-08 · vendor
  6. IEMAI CF-ABS 3D Printing Filament product page IEMAI 3D · 2026-08 · vendor
  7. Siraya Tech Fibreheart ABS-CF Filament product page Siraya Tech · 2026-08 · vendor
  8. YXPOLYER ABS CF product page YXPOLYER · 2026-08 · vendor
  9. Polymaker product catalogue Polymaker · 2026-08 · vendor
  10. Siraya Tech Fibreheart ABS-CF Core Filament product page Siraya Tech · 2026-08 · vendor
  11. ABS / ASA / PC Usage Guide Bambu Lab Wiki · 2026-08 · doc
  12. ABS — Ultimate 3D Printing Materials Guide Simplify3D · 2026-08 · doc
  13. Prusament PETG Technical Datasheet v1.1 Prusa Polymers · 2022-02 · tds
  14. PETG — material basics Polymaker Wiki · 2026-08 · doc
  15. Max volumetric speed Prusa Knowledge Base · 2026-08 · doc
  16. ABS — material basics Polymaker Wiki · 2026-08 · doc
  17. CARBONX ABS+CF — product page (print recommendations) 3DXTech · 2026-08 · doc
  18. Composite materials filled with carbon, kevlar or glass Prusa Knowledge Base · 2026-08 · doc
  19. Carbon Fiber Filled — Ultimate 3D Printing Materials Guide Simplify3D · 2026-08 · doc
  20. 3DXSTAT ESD-PETG — product page (print recommendations) 3DXTech · 2026-08 · doc
  21. PET and PETG — Ultimate 3D Printing Materials Guide Simplify3D · 2026-08 · doc
  22. Bambu Filament Technical Data Sheet V3.0 — ABS Bambu Lab · 2026-08 · tds
  23. Polymaker ABS Pro Technical Data Sheet V1 (2026-05-29) Polymaker · 2026-05 · tds
  24. Wet Filament — signs, causes and drying Polymaker Wiki · 2026-08 · doc
  25. PCTG vs PETG comparison — results spreadsheet My Tech Fun (Igor Gaspar) · 2026-08 · test
  26. Extrudr PETG vs PCTG vs XPETG-CF — results spreadsheet My Tech Fun (Igor Gaspar) · 2026-08 · test
  27. Prusament PETG-CF vs PETG V0 vs PETG — results spreadsheet My Tech Fun (Igor Gaspar) · 2026-08 · test
  28. BambuLab PETG Basic vs Translucent vs PETG-CF — results spreadsheet My Tech Fun (Igor Gaspar) · 2026-08 · test
  29. Mechanical Properties of Additively Manufactured Polymeric Materials — PLA and PETG — For Biomechanical Applications Polymers 16(13):1868 · 2024-06 · paper
  30. Effects of Fiber Orientation on the Coefficient of Thermal Expansion of Fiber-Filled Polymer Systems in Large Format Polymer Extrusion-Based Additive Manufacturing Materials 15(8):2764 · 2022-04 · paper
  31. Prusament PETG V0 Technical Datasheet Prusa Polymers · 2026-08 · tds
  32. PolyLite ABS Technical Data Sheet (V5.5 served at this URL) Polymaker · 2024-11 · tds
  33. Emissions of Ultrafine Particles and Volatile Organic Compounds from Commercially Available Desktop Three-Dimensional Printers with Multiple Filaments (Azimi et al.) Environmental Science & Technology 50(3) 1260-1268 · 2016-01 · paper
  34. HIPS — Ultimate 3D Printing Materials Guide Simplify3D · 2026-08 · doc
  35. Chemical resistance — resistance of Ensinger plastics to chemicals (DIN 50 014, 23/50) Ensinger · 2026-08 · tds
  36. Eastman Spectar copolyester — Chemical resistance (unstressed bars, 1 year at 23 °C) Eastman Chemical Company · 2026-08 · tds
  37. Improve your 3D prints with chemical smoothing Prusa Research · 2026-08 · doc
  38. HIPS — Knowledge Base Prusa Research · 2026-08 · doc