3D Printing Info

Filament comparison

ABS-CF vs PEEK

Compare printing settings, strength, heat resistance, dated prices and sources.

Carbon-fibre ABS (ABS-CF) guidePEEK guide

2 selected · all documented properties

Open these two in the interactive comparisonMore ABS-CF comparisonsMore PEEK comparisons
ABS-CF vs PEEK — documented properties and sources
PropertyCarbon-fibre ABS (ABS-CF)ABSPEEKHIGHTEMP
Market snapshot
Listing priceUSD/kg; dated snapshots$35.99/kg median; $22.00–$125.00/kg across 7 dated product listings$531.87/kg median; $296.14–$770.00/kg across 5 dated product listings
Identity & Market
Base polymer / chemistryABS reinforced with chopped carbon fibre[1]Polyether ether ketone — a semi-crystalline polyaryletherketone[2]
Densityg/cm³1.11 (ISO 1183)[1]1.30 (ISO 1183)[2][3]
Typical priceUSD/kg1 kg-equivalent spools span 22–125; the middle of the market is about 36[4][5][6][7][8]1 kg-equivalent spools span 296–770; the middle of the market is about 532[4][9][10]
Price range across brandsUSD/kg22–125 across brands; IEMAI 22, Siraya Tech 28 and 36 for the core-shell grade, YXPOLYER 35, Push Plastic 50 at 2 kg, 3DXTech 64 at 750 g; Stratasys-compatible cartridges run far higher[4][5][6][7][11][8]296-770 across brands and spool sizes; 3D4Makers recycled R-PEEK 296 at 750 g, IEMAI 3D 420 at 1 kg, LEHVOSS Luvocom 3F PEEK 9581 532 at 2 kg, 3DXTech ThermaX PEEK 770 at 500 g[4][9][10]
Market availability1–5Available from several mainstream brands[4][5]Niche, a handful of specialist brands[4][9][3]
Spool sizes & diameters1.75 and 2.85 mm; 0.5, 0.75 and 2 kg spools plus Stratasys-compatible cartridges[4][5]1.75 and 2.85 mm; 200 g to 2 kg spools[4][9][3]
Typical applicationsStiff tooling and fixtures that must survive above 100 °C[1]Aerospace brackets, semiconductor handling, sterilisable medical tooling and downhole parts[2]
Printing Parameters
Nozzle temperature°CNot documented380-400 (3DXTech printed-specimen conditions); Victrex quotes a 340-450 melt range for AM 450 FIL[2][3]
Bed temperature°CNot documented130–140 (3DXTech)[2]
Enclosure / chamber requirement1–5Enclosure recommended[12]Actively heated chamber required[13][14]
Recommended chamber temperature°CNot documentedNot less than 150 for semi-crystalline printing (Victrex AM 450 FIL); bed above 150[3]
Bed surface & adhesion aidClean the plate and apply glue; Simplify3D also lists Kapton tape and ABS slurry[12][15]Not documented
Warping tendency1–5Moderate — needs adhesion aid or draught shield; the fibre reduces warping against unfilled ABS[12]Severe — heated chamber needed[13]
Bed-adhesion difficulty1–5Needs a specific surface plus adhesive[12]Very difficult — special plates or slurry required[13]
Stringing / oozing tendency1–5Slight — Polymaker advises 1–2 mm retraction at 20–30 mm/s[16]Not documented
Overall printing difficulty1–5Intermediate — dry filament and a tuned profile; hardened nozzle mandatory[12]Expert / industrial hardware only[13][14]
Extruder requirementNot documentedAn all-metal hot end rated above 400 °C and a heated chamber; 3DXTech tests at 0.25 mm layer height on a 0.4 mm nozzle[2][13]
Hardware Wear & Reliability
Nozzle hardness required1–4Hardened steel required[12]Brass fine indefinitely for unfilled grades, but brass softens near these nozzle temperatures — hardened or plated hot ends are the norm[13]
Abrasiveness1–5Highly abrasive — standard CF composite[12]Non-abrasive when unfilled[2]
Nozzle clog risk1–5Moderate — needs dry filament and a clean nozzle; 3DXTech specifies a hardened nozzle of 0.4 mm minimum and 0.25 mm layers or higher, and Prusa lists composites as a higher clogging risk[17][18][19]Moderate — needs dry filament and a clean nozzle; 3DXTech lists no special nozzle concerns but a mandatory 120 °C pre-dry before every print[20]
Heat-creep / jam sensitivity1–5Slightly sensitive[15]Not documented
Hotend requirementNo special hot-end required[15]Not documented
Moisture Behaviour
Moisture absorption (hygroscopicity)1–5Moderate — the ABS matrix takes up 0.51–0.65 % saturated at 25 °C / 55 % RH and 3DXTech specifies a 80 °C, 4 h pre-dry[21][22][17]Not documented
Equilibrium moisture content at ~50 % RH%Not documented0.45 at saturation, 23 °C (ISO 62); 0.55 at 100 °C[3]
Drying temperature & timeNot documented120 °C for 5 h, target below 0.020 % moisture (Victrex AM 450 FIL)[3]
Symptoms when wetBubbling and popping at the nozzle, stringing and a rough surface[23]Not documented
Effect of moisture on strengthPolymaker rates ABS moderate-sensitivity and publishes no dry-versus-conditioned figures; absorbed water flashes to steam in the hotend and shows as bubbling and poor layer adhesion[23]No dry-versus-conditioned figures are published; 3DXTech mandates a 120 °C, 4 h pre-dry before every print because trapped water flashes to steam at these nozzle temperatures[20]
Storage requirementSealed with desiccant; Polymaker rates ABS moderate-sensitivity[23]Not documented
Mechanical Properties
Tensile strength (XY)MPa46 at break (printed XY, ISO 527)[1]60-100 (printed XY): Victrex AM 450 FIL 60-80 at yield and 3DXTech 100, both ISO 527; 98 at yield injection-moulded[2][3]
Young's modulusMPa5210 (printed XY, ISO 527) — more than double unfilled ABS[1]3000-4000 (printed XY, ISO 527, Victrex AM 450 FIL); 3720 (3DXTech); 4000 injection-moulded[2][3]
Elongation at break%2 at break (printed XY, ISO 527)[1]28 (printed XY, ISO 527) — remarkably ductile for a high-temperature polymer[2]
Flexural strengthMPa76 (printed XY, ISO 178)[1]130 (printed XY, ISO 178)[2]
Flexural modulusMPa5260 (printed XY, ISO 178)[1]2700 (printed XY, ISO 178)[2]
Charpy impact, notchedkJ/m²Not documented6.0 (injection-moulded, ISO 179/1eA); unnotched does not break[3]
Other impact dataNot documentedIzod notched 7.0 kJ/m2 injection-moulded (ISO 180/A). Printed anisotropy is extreme: VICTREX AM 200 on a Stratasys F900 gives Izod notched 1380-1530 J/m XZ against 30-62 J/m ZX (ASTM D256)[3][24]
Layer adhesion / Z tensileMPaNot documented20-85 at yield (printed ZX, ISO 527, Victrex AM 450 FIL); the spread is set by chamber temperature and weld quality[3]
Brittleness1–5Brittle — snaps with little warning; elongation at break 2 %[1]Tough — absorbs impact, yields before breaking[2]
Hardness (scale-specific)Shore A / Shore D / RockwellNot documentedShore D 84.5 (injection-moulded, ISO 868); Rockwell M100 / R125 on extruded PEEK stock (ASTM D785)[3][25]
Creep resistance / sustained load1–5Good — no creep test found; chopped carbon fibre restrains matrix flow and modulus rises to 5210 MPa against 2200–2330 for unfilled ABS[1][21][22]Excellent — holds load for years. Victrex rates PEEK for long-term creep; injection-moulded flexural stress at 3.5 % strain falls only from 125 MPa at 23 °C to 85 MPa at 125 °C, and extruded stock is rated to 249 °C continuous[26][3][25]
Fatigue / repeated-flex resistance1–5Below average — no S-N curve found; elongation at break falls to 2 % against 10.5 % for unfilled ABS[1][21]Excellent — living hinges viable. Victrex rates PEEK for long-term fatigue as well as creep[26]
Elasticity / flexibility1–5Rigid[1]Rigid[2]
Z strength as % of XY%Not documented71-84 (VICTREX AM 200 LMPAEK printed on the Stratasys F900 and Fortus 450mc, ZX against XZ tensile yield, ASTM D638); unfilled PEEK's own ZX spread is wider[24]
Thermal Properties
HDT at 0.45 MPa°CNot documented140 (printed XY, ISO 75 at 0.45 MPa, 3DXTech)[2]
HDT at 1.8 MPa°CNot documented152 (unannealed, ISO 75-2/Af, Victrex AM 450 FIL); 160 on extruded stock (ASTM D648 at 264 psi)[3][25]
Glass transition (Tg)°C105 (DSC)[1]143 (DSC, 3DXTech); Victrex gives onset 143 and midpoint 150 (ISO 11357-2)[2][3]
Melting point / Vicat°CNot documented343 melting (ISO 11357-3, Victrex); VICTREX AM 200 LMPAEK melts at 303[3][24]
Continuous service temperature°CNot documented240 UL 746B relative thermal index, strength (RTI electrical 260, impact 180); Ensinger rates extruded PEEK stock at 249 long term[3][25]
Thermal expansion (CTE)µm/m·K19–25 along the print bead and 80–84 in the build direction at 30 °C (20 wt% CF, large-format printed, TMA)[27]37.8 (extruded PEEK stock, 23-60 °C, ASTM E831; source states 2.1e-5 in/in/°F), rising to 41.9 at 60-100 °C and 55.8 at 100-150 °C[25]
Flammability / UL 94Not documentedUL 94 V-0 at 1.5 mm on the base resin; glow-wire flammability index 960 °C at 2.0 mm (IEC 60695-2-12)[2][3]
Environment & Chemical
Chemical resistanceGood against weak acids, weak alkalis, oils and grease; dissolved by acetone[28]Outstanding — resistant to almost all solvents and to steam sterilisation[2]
Water / humidity resistance in service1–5Not documentedExcellent — essentially unaffected; 0.45 % water at saturation and resistant to steam sterilisation[3][2]
Food contactNot food safe — Polymaker cites potential chemical leaching[16]Not documented
Biodegradability / compostabilityNot biodegradable[16]Not documented
RecyclabilityMechanically recyclable but not accepted in household plastic collection[16]Not documented
Electrical & ESD propertiesSurface resistance above 10⁹ ohm/sq — not static-dissipative (ASTM D257)[1]Not documented
Health & Safety
Fume toxicity1–5High — hazardous VOC such as styrene; enclosure and filtration needed[29][12]Moderate — measurable VOCs and UFPs, ventilation advised. None of these polymers was in the chamber study, and all are processed far above the temperatures it covered[29]
VOC emission rateµg/min12–113 styrene, the dominant VOC from every ABS and HIPS combination tested[29]Not documented
Ultrafine-particle emission rateparticles/min2 × 10¹⁰ to 9 × 10¹⁰ median across all ABS printers, two orders of magnitude above PLA's ≈1 × 10⁸[29]Not documented
Hazardous species emittedStyrene dominates. Bambu Lab states ABS and ASA release harmful gases such as styrene at printing temperature, which can be toxic and cause dizziness or nausea[29][12]Not documented
Ventilation / filtration requirement1–5Enclosure with carbon and HEPA filtration — an enclosure alone cut measured UFP by only about 35 %[29][12]Ventilated room or enclosure recommended[29]
Dust & fibre handling hazardCarbon fibre is bound in the matrix; sanding dust should not be inhaled[1]Not documented
Post-Processing
Sanding & machiningSands well and takes filler before painting[16]Not documented
Painting & finishingPaints readily after light abrasion[16]Not documented
Vapour / chemical smoothingAcetone smoothing is blunted by the fibre — only the resin fraction dissolves[28]Not documented
Support material pairingHIPS breaks away or dissolves in d-limonene; Bambu Lab sells a dedicated Support for ABS[30][12]Not documented
Solvents & Solubility
Soluble inAcetone dissolves the resin and leaves the fibre as sludge; MEK, THF, ethyl acetate and chlorinated solvents do the same.[31][28]95–98 wt% sulphuric acid dissolves it — 10 g per 100 mL at 40–70 °C gives a dark red solution. Laboratory route only.[32][31]
Softened or crazed byPetrol and perchloroethylene soften it and benzene attacks it; d-limonene disrupts layer adhesion in some ABS and ASA grades.[31][33]Concentrated nitric, hydrofluoric, hydrobromic and hydriodic acids attack it; DCM, DMSO and THF swell thin-walled sections.[34][31]
Solvent welding & smoothing agentAcetone vapour reaches only the resin fraction, so the fibre is left standing proud of the smoothed surface.[35][28]None — no solvent softens PEEK, so parts are joined thermally or mechanically, never chemically.[34][31]

Material entries describe families or representative grades, not an interchangeable specification for every spool. Test methods, orientations and conditions may differ. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.

Sources for this comparison

  1. CarbonX Carbon Fiber ABS Technical Data Sheet 3DXTech · 2026-08 · tds
  2. ThermaX PEEK Technical Data Sheet v3 3DXTech · 2026-08 · tds
  3. VICTREX AM 450 FIL — datasheet Victrex · 2025-12 · tds
  4. 3DXTech product catalogue 3DXTech · 2026-08 · vendor
  5. Push Plastic product catalogue Push Plastic · 2026-08 · vendor
  6. IEMAI CF-ABS 3D Printing Filament product page IEMAI 3D · 2026-08 · vendor
  7. Siraya Tech Fibreheart ABS-CF Filament product page Siraya Tech · 2026-08 · vendor
  8. YXPOLYER ABS CF product page YXPOLYER · 2026-08 · vendor
  9. 3D4Makers product catalogue 3D4Makers · 2026-08 · vendor
  10. IEMAI 3D PEEK 3D Printing Filament — store page IEMAI 3D · 2026-08 · vendor
  11. Siraya Tech Fibreheart ABS-CF Core Filament product page Siraya Tech · 2026-08 · vendor
  12. ABS / ASA / PC Usage Guide Bambu Lab Wiki · 2026-08 · doc
  13. Prusament PEI 1010 Technical Datasheet v1.0 Prusa Polymers · 2024-09 · tds
  14. Prusament PEI 1010 — material page Prusa Polymers · 2026-08 · doc
  15. ABS — Ultimate 3D Printing Materials Guide Simplify3D · 2026-08 · doc
  16. ABS — material basics Polymaker Wiki · 2026-08 · doc
  17. CARBONX ABS+CF — product page (print recommendations) 3DXTech · 2026-08 · doc
  18. Composite materials filled with carbon, kevlar or glass Prusa Knowledge Base · 2026-08 · doc
  19. Carbon Fiber Filled — Ultimate 3D Printing Materials Guide Simplify3D · 2026-08 · doc
  20. ThermaX PEEK — product page 3DXTech · 2026-08 · vendor
  21. Bambu Filament Technical Data Sheet V3.0 — ABS Bambu Lab · 2026-08 · tds
  22. Polymaker ABS Pro Technical Data Sheet V1 (2026-05-29) Polymaker · 2026-05 · tds
  23. Wet Filament — signs, causes and drying Polymaker Wiki · 2026-08 · doc
  24. VICTREX AM 200 — FDM Material Data Sheet Stratasys · 2024-04 · tds
  25. TECAPEEK natural (PEEK) — stock shape properties Ensinger · 2026-08 · tds
  26. PEEK polymers — product overview Victrex · 2026-08 · doc
  27. Effects of Fiber Orientation on the Coefficient of Thermal Expansion of Fiber-Filled Polymer Systems in Large Format Polymer Extrusion-Based Additive Manufacturing Materials 15(8):2764 · 2022-04 · paper
  28. PolyLite ABS Technical Data Sheet (V5.5 served at this URL) Polymaker · 2024-11 · tds
  29. Emissions of Ultrafine Particles and Volatile Organic Compounds from Commercially Available Desktop Three-Dimensional Printers with Multiple Filaments (Azimi et al.) Environmental Science & Technology 50(3) 1260-1268 · 2016-01 · paper
  30. HIPS — Ultimate 3D Printing Materials Guide Simplify3D · 2026-08 · doc
  31. Chemical resistance — resistance of Ensinger plastics to chemicals (DIN 50 014, 23/50) Ensinger · 2026-08 · tds
  32. The Effects of Sulfonated Poly(ether ether ketone) Ion Exchange Preparation Conditions on Membrane Properties Yee, Zhang & Ladewig, Membranes 3(3) 182–195 · 2013-07 · paper
  33. HIPS — Knowledge Base Prusa Research · 2026-08 · doc
  34. What solvents are not compatible with PEEK? — fluidics technical FAQ IDEX Health & Science · 2026-08 · doc
  35. Improve your 3D prints with chemical smoothing Prusa Research · 2026-08 · doc