3D Printing Info

Filament comparison

ABS-CF vs PCTG

Compare printing settings, strength, heat resistance, dated prices and sources.

Carbon-fibre ABS (ABS-CF) guidePCTG guide

2 selected · all documented properties

Open these two in the interactive comparisonMore ABS-CF comparisonsMore PCTG comparisons
ABS-CF vs PCTG — documented properties and sources
PropertyCarbon-fibre ABS (ABS-CF)ABSPCTGPETG
Market snapshot
Listing priceUSD/kg; dated snapshots$35.99/kg median; $22.00–$125.00/kg across 7 dated product listings$34.99/kg median; $14.00–$50.67/kg across 5 dated product listings
Identity & Market
Base polymer / chemistryABS reinforced with chopped carbon fibre[1]Poly(cyclohexylenedimethylene terephthalate) glycol — a copolyester with a higher cyclohexanedimethanol content than PETG[2][3]
Densityg/cm³1.11 (ISO 1183)[1]1.23 (Extrudr, ASTM D792; 3DXTech, ISO 1183)[3][4]
Typical priceUSD/kg1 kg-equivalent spools span 22–125; the middle of the market is about 36[5][6][7][8][9]1 kg spools cluster near 34[6][4][10]
Price range across brandsUSD/kg22–125 across brands; IEMAI 22, Siraya Tech 28 and 36 for the core-shell grade, YXPOLYER 35, Push Plastic 50 at 2 kg, 3DXTech 64 at 750 g; Stratasys-compatible cartridges run far higher[5][6][7][8][11][9]14–51 across brands; CHCKX 14 in a 10-roll bundle, Push Plastic 30, Proto-pasta 35 at 1 kg, 3DXTech 51[6][4][12]
Market availability1–5Available from several mainstream brands[5][6]Available from several mainstream brands[6][4][10][13]
Spool sizes & diameters1.75 and 2.85 mm; 0.5, 0.75 and 2 kg spools plus Stratasys-compatible cartridges[5][6]1.75 and 2.85 mm; 0.5, 0.75, 1, 3 and 5 kg spools[6][10][4]
Typical applicationsStiff tooling and fixtures that must survive above 100 °C[1]Transparent covers, guards and impact-loaded parts where PETG cracks[2][3]
Printing Parameters
Nozzle temperature°CNot documented250–270 (Spectrum, Extrudr)[2][3]
Bed temperature°CNot documented60–100 (Spectrum)[2]
Enclosure / chamber requirement1–5Enclosure recommended[14]Open frame is fine — Spectrum and Extrudr both say a closed chamber is not necessary, Extrudr adds it helps on larger parts[2][3]
Part cooling fanNot documentedUp to 100 % (Spectrum); 20–50 % (Extrudr)[2][3]
Bed surface & adhesion aidClean the plate and apply glue; Simplify3D also lists Kapton tape and ABS slurry[14][15]Textured PEI, satin or powder-coated sheets; on smooth PEI a glue stick acts as a release agent[16][17]
Maximum volumetric flow (mm³/s; see test conditions)mm³/sNot documented1.6–16 at the 20–200 mm/s Extrudr rates the material for, on a 0.4 mm nozzle at 0.2 mm layer[3][18]
Warping tendency1–5Moderate — needs adhesion aid or draught shield; the fibre reduces warping against unfilled ABS[14]Not documented
Bed-adhesion difficulty1–5Needs a specific surface plus adhesive[14]Needs the right surface or a thin adhesive — the problem is releasing the part, not sticking it[16][17]
Stringing / oozing tendency1–5Slight — Polymaker advises 1–2 mm retraction at 20–30 mm/s[19]Moderate — retraction tuning needed; Polymaker names stringing as PETG's common quirk[17]
Shrinkage%Not documented0.2–0.5 (Extrudr, ASTM D955)[3]
Overall printing difficulty1–5Intermediate — dry filament and a tuned profile; hardened nozzle mandatory[14]Easy — minor profile tuning[2][3]
Hardware Wear & Reliability
Nozzle hardness required1–4Hardened steel required[14]Brass fine indefinitely — Extrudr explicitly states no hardened nozzle is needed[3]
Abrasiveness1–5Highly abrasive — standard CF composite[14]Non-abrasive[3]
Nozzle clog risk1–5Moderate — needs dry filament and a clean nozzle; 3DXTech specifies a hardened nozzle of 0.4 mm minimum and 0.25 mm layers or higher, and Prusa lists composites as a higher clogging risk[20][21][22]Low — 3DXTech lists no special nozzle concerns and no minimum layer height for PCTG, only a 65 °C pre-dry[23]
Heat-creep / jam sensitivity1–5Slightly sensitive[15]Slightly sensitive[24]
Hotend requirementNo special hot-end required[15]No special hot-end required[24]
Moisture Behaviour
Moisture absorption (hygroscopicity)1–5Moderate — the ABS matrix takes up 0.51–0.65 % saturated at 25 °C / 55 % RH and 3DXTech specifies a 80 °C, 4 h pre-dry[25][26][20]Moderate (0.3–0.8 %) — the copolyester matrix reaches 0.40 % saturated at 25 °C / 55 % RH and 3DXTech specifies a 65 °C, 4 h pre-dry[16][23]
Symptoms when wetBubbling and popping at the nozzle, stringing and a rough surface[27]Bubbling and popping at the nozzle, stringing and a rough surface[27]
Effect of moisture on strengthPolymaker rates ABS moderate-sensitivity and publishes no dry-versus-conditioned figures; absorbed water flashes to steam in the hotend and shows as bubbling and poor layer adhesion[27]Polymaker groups PETG with nylon, PVA and TPU as highly hygroscopic; no dry-versus-conditioned strength figures are published for this grade and the loss shows as bubbling and poor layer adhesion[27]
Storage requirementSealed with desiccant; Polymaker rates ABS moderate-sensitivity[27]Sealed with desiccant; Polymaker groups PETG with the highly hygroscopic materials[27][17]
Mechanical Properties
Tensile strength (XY)MPa46 at break (printed XY, ISO 527)[1]43–44 at yield and 45–46 at break (ISO 527, injection-moulded resin data from Spectrum and Extrudr); 48 on My Tech Fun printed bars[2][3][28]
Young's modulusMPa5210 (printed XY, ISO 527) — more than double unfilled ABS[1]Not documented
Elongation at break%2 at break (printed XY, ISO 527)[1]215–220 at break on moulded specimens (ISO 527); 4.3–4.4 at yield[2][3]
Flexural strengthMPa76 (printed XY, ISO 178)[1]Not documented
Flexural modulusMPa5260 (printed XY, ISO 178)[1]Not documented
Charpy impact, notchedkJ/m²Not documented93–94 notched Izod at 23 °C on moulded specimens (ISO 180); 3DXTech quotes 8 by ISO 180/A[2][3][4]
Other impact dataNot documentedIzod 4.14 kJ/m² on My Tech Fun printed bars, against 3.37 for PETG on the same rig[28]
Layer adhesion / Z tensileMPaNot documented21.6 on My Tech Fun 4×4 mm printed bars, against 32.9 for PETG[28]
Brittleness1–5Brittle — snaps with little warning; elongation at break 2 %[1]Tough — absorbs impact, yields before breaking[2][3]
Hardness (scale-specific)Shore A / Shore D / RockwellNot documented69 Shore D measured by My Tech Fun, against 72 for PETG[28]
Creep resistance / sustained load1–5Good — no creep test found; chopped carbon fibre restrains matrix flow and modulus rises to 5210 MPa against 2200–2330 for unfilled ABS[1][25][26]Below average — a 12 mm bar sagged to 19.4 mm over 5 days at 1.25 kg, slightly worse than PETG's 18.2[28]
Fatigue / repeated-flex resistance1–5Below average — no S-N curve found; elongation at break falls to 2 % against 10.5 % for unfilled ABS[1][25]Good — 215 % elongation at break and 94 kJ/m² notched Izod on moulded specimens (Extrudr, Spectrum)[2][3]
Elasticity / flexibility1–5Rigid[1]Slightly flexible in thin sections[28]
Thermal Properties
Glass transition (Tg)°C105 (DSC)[1]78 (3DXTech, DSC)[4]
Melting point / Vicat°CNot documentedAmorphous — no melting point; Vicat 88 (Spectrum, Extrudr)[2][3]
Continuous service temperature°CNot documented68 — loaded bars begin to move at this temperature, against 65 for PETG[28]
Thermal expansion (CTE)µm/m·K19–25 along the print bead and 80–84 in the build direction at 30 °C (20 wt% CF, large-format printed, TMA)[29]Not documented
Flammability / UL 94Not documentedFlammable; no UL 94 rating published for standard grades[30]
Environment & Chemical
Chemical resistanceGood against weak acids, weak alkalis, oils and grease; dissolved by acetone[31]Withstands acids, alkalis, oils and UV exposure[17]
Water / humidity resistance in service1–5Not documentedGood — minor absorption; Spectrum describes the polymer as hydrophobic[2]
Food contactNot food safe — Polymaker cites potential chemical leaching[19]Not certified for food contact as filament[17]
Biodegradability / compostabilityNot biodegradable[19]Not biodegradable[17]
RecyclabilityMechanically recyclable but not accepted in household plastic collection[19]Not accepted in household plastic collection[17]
Electrical & ESD propertiesSurface resistance above 10⁹ ohm/sq — not static-dissipative (ASTM D257)[1]Surface resistance above 10¹³ ohm/sq — insulating (3DXTech, ASTM D257)[4]
Health & Safety
Fume toxicity1–5High — hazardous VOC such as styrene; enclosure and filtration needed[32][14]Moderate — measurable VOCs and UFPs, ventilation advised[32]
VOC emission rateµg/min12–113 styrene, the dominant VOC from every ABS and HIPS combination tested[32]Not documented
Ultrafine-particle emission rateparticles/min2 × 10¹⁰ to 9 × 10¹⁰ median across all ABS printers, two orders of magnitude above PLA's ≈1 × 10⁸[32]Not documented
Hazardous species emittedStyrene dominates. Bambu Lab states ABS and ASA release harmful gases such as styrene at printing temperature, which can be toxic and cause dizziness or nausea[32][14]Not documented
Ventilation / filtration requirement1–5Enclosure with carbon and HEPA filtration — an enclosure alone cut measured UFP by only about 35 %[32][14]Open a window / occasional ventilation[32]
Dust & fibre handling hazardCarbon fibre is bound in the matrix; sanding dust should not be inhaled[1]Not documented
Post-Processing
Sanding & machiningSands well and takes filler before painting[19]Sands poorly — the material is tough and gums rather than powders[24]
Painting & finishingPaints readily after light abrasion[19]Not documented
Gluing & solvent weldingNot documentedCyanoacrylate; no common solvent welds PETG cleanly[24]
Vapour / chemical smoothingAcetone smoothing is blunted by the fibre — only the resin fraction dissolves[31]No practical vapour smoothing[24]
Support material pairingHIPS breaks away or dissolves in d-limonene; Bambu Lab sells a dedicated Support for ABS[33][14]Prints its own supports; Polymaker rates PolyDissolve S1 for PETG[24]
Dimensional accuracy & detailNot documentedOptical clarity is the selling point; Extrudr recommends a layer height at most 50 % of nozzle diameter[3]
Solvents & Solubility
Soluble inAcetone dissolves the resin and leaves the fibre as sludge; MEK, THF, ethyl acetate and chlorinated solvents do the same.[34][31]No common workshop solvent; Eastman's CHDM copolyester data shows 1,2-dichloroethane destroying it within a week.[35]
Softened or crazed byPetrol and perchloroethylene soften it and benzene attacks it; d-limonene disrupts layer adhesion in some ABS and ASA grades.[34][36]Acetone, ethyl acetate, toluene and DMF swell and soften the copolyester; methanol crazes it (Eastman, 1 y at 23 °C).[35]
Solvent welding & smoothing agentAcetone vapour reaches only the resin fraction, so the fibre is left standing proud of the smoothed surface.[37][31]Dichloromethane brushed on is the only agent that smooths PETG — a controlled carcinogen, not workshop stock.[37]

Material entries describe families or representative grades, not an interchangeable specification for every spool. Test methods, orientations and conditions may differ. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.

Sources for this comparison

  1. CarbonX Carbon Fiber ABS Technical Data Sheet 3DXTech · 2026-08 · tds
  2. Spectrum Premium PCTG Technical Data Sheet Spectrum Filaments · 2026-08 · tds
  3. Extrudr PCTG technical data Extrudr · 2026-08 · tds
  4. MAX-G PCTG Technical Data Sheet 3DXTech · 2026-08 · tds
  5. 3DXTech product catalogue 3DXTech · 2026-08 · vendor
  6. Push Plastic product catalogue Push Plastic · 2026-08 · vendor
  7. IEMAI CF-ABS 3D Printing Filament product page IEMAI 3D · 2026-08 · vendor
  8. Siraya Tech Fibreheart ABS-CF Filament product page Siraya Tech · 2026-08 · vendor
  9. YXPOLYER ABS CF product page YXPOLYER · 2026-08 · vendor
  10. Proto-pasta product catalogue Proto-pasta · 2026-08 · vendor
  11. Siraya Tech Fibreheart ABS-CF Core Filament product page Siraya Tech · 2026-08 · vendor
  12. CHCKX 10KG Multicolor PCTG Filament bundle CHCKX (Amazon US) · 2026-08 · vendor
  13. Atomic Filament product catalogue Atomic Filament · 2026-08 · vendor
  14. ABS / ASA / PC Usage Guide Bambu Lab Wiki · 2026-08 · doc
  15. ABS — Ultimate 3D Printing Materials Guide Simplify3D · 2026-08 · doc
  16. Prusament PETG Technical Datasheet v1.1 Prusa Polymers · 2022-02 · tds
  17. PETG — material basics Polymaker Wiki · 2026-08 · doc
  18. Max volumetric speed Prusa Knowledge Base · 2026-08 · doc
  19. ABS — material basics Polymaker Wiki · 2026-08 · doc
  20. CARBONX ABS+CF — product page (print recommendations) 3DXTech · 2026-08 · doc
  21. Composite materials filled with carbon, kevlar or glass Prusa Knowledge Base · 2026-08 · doc
  22. Carbon Fiber Filled — Ultimate 3D Printing Materials Guide Simplify3D · 2026-08 · doc
  23. MAX-G PCTG — product page (print recommendations) 3DXTech · 2026-08 · doc
  24. PET and PETG — Ultimate 3D Printing Materials Guide Simplify3D · 2026-08 · doc
  25. Bambu Filament Technical Data Sheet V3.0 — ABS Bambu Lab · 2026-08 · tds
  26. Polymaker ABS Pro Technical Data Sheet V1 (2026-05-29) Polymaker · 2026-05 · tds
  27. Wet Filament — signs, causes and drying Polymaker Wiki · 2026-08 · doc
  28. PCTG vs PETG comparison — results spreadsheet My Tech Fun (Igor Gaspar) · 2026-08 · test
  29. Effects of Fiber Orientation on the Coefficient of Thermal Expansion of Fiber-Filled Polymer Systems in Large Format Polymer Extrusion-Based Additive Manufacturing Materials 15(8):2764 · 2022-04 · paper
  30. Prusament PETG V0 Technical Datasheet Prusa Polymers · 2026-08 · tds
  31. PolyLite ABS Technical Data Sheet (V5.5 served at this URL) Polymaker · 2024-11 · tds
  32. Emissions of Ultrafine Particles and Volatile Organic Compounds from Commercially Available Desktop Three-Dimensional Printers with Multiple Filaments (Azimi et al.) Environmental Science & Technology 50(3) 1260-1268 · 2016-01 · paper
  33. HIPS — Ultimate 3D Printing Materials Guide Simplify3D · 2026-08 · doc
  34. Chemical resistance — resistance of Ensinger plastics to chemicals (DIN 50 014, 23/50) Ensinger · 2026-08 · tds
  35. Eastman Spectar copolyester — Chemical resistance (unstressed bars, 1 year at 23 °C) Eastman Chemical Company · 2026-08 · tds
  36. HIPS — Knowledge Base Prusa Research · 2026-08 · doc
  37. Improve your 3D prints with chemical smoothing Prusa Research · 2026-08 · doc