3D Printing InfoPrinter comparison
Stratasys F370 vs UltiMaker Factor 4
Compare hardware, build volume, printing specifications, dated prices and sources.
2 selected · all documented properties
Open these two in the interactive comparisonMore Stratasys F370 comparisonsMore UltiMaker Factor 4 comparisons
| Property | Stratasys F370INDUSTRIAL | UltiMaker Factor 4INDUSTRIAL |
|---|---|---|
| Identity | ||
| Brand | Stratasys | UltiMaker |
| Class | INDUSTRIAL | INDUSTRIAL |
| Identity & Market | ||
| Manufacturer & exact marketed model name (verify the exact product identity first) | Stratasys F370, part of the Stratasys F123 Series[1] | UltiMaker Factor 4[2] |
| Release date (announcement and actual shipping) | The F123 series spec sheet carried is revision 0721a (July 2021). Stratasys does not print a launch date on it[1] | Announced 22 April 2024, shown at HANNOVER MESSE 2024 (22-26 April) and TCT Asia (7-9 May 2024)[2] |
| Launch MSRP (USD) | Not documented | Starting at approximately $20,000[2] |
| Variants & sibling models — and how to tell them apart (spec-contamination risk) | Top of the series and the only one with ABS-ESD7, PC-ABS and Diran 410MF07, an Insight software licence, and ProtectAM with US DoD STIG compliance on Red Hat Enterprise Linux. Cabinet and weight are identical to the F170 and F270, so footprint tells you nothing about which model you have[1] | Shares the 330 x 240 x 300 mm envelope with the UltiMaker S5, S7 and S8, which is the single most contaminated figure in UltiMaker's range. What separates the Factor 4 is the actively controlled 70 °C build volume, the climate-controlled 6-spool material station holding humidity below 15%, and HEPA filtration. UltiMaker also sells a Factor 4 Plus[2] |
| Physical & Frame | ||
| Build volume X×Y×Z (mm) — advertised vs actually usable | 355 x 254 x 355 mm (14 x 10 x 14 in)[1] | 330 x 240 x 300 mm[2] |
| Machine footprint (mm) & clearance needed (cable/spool overhang) | 1,626 x 864 x 711 mm (64 x 34 x 28 in)[1] | Not documented |
| Net weight (kg) | 124 kg (F120) or 227 kg with consumables (F170, F270, F370)[1] | Not documented |
| Frame construction & material | Fully enclosed office/classroom-grade cabinet, factory assembled[1] | Not documented |
| Enclosure: open / enclosed; panel material; door/lid | Enclosed build chamber[1] | Enclosed with actively controlled chamber airflow and a HEPA filter[2] |
| Passive chamber temperature reached (if enclosed; measured values preferred) | Not documented | Build volume temperature controlled up to 70 °C with actively controlled chamber airflow (manufacturer specification)[2] |
| Kinematics & Motion Hardware | ||
| Kinematics (bedslinger i3 / CoreXY / other) | Not documented | Direct-drive dual extrusion; kinematic layout not stated in the source checked[2] |
| Extruder | ||
| Type (direct drive / bowden) & design name | Not documented | Direct-drive dual extrusion[2] |
| Filament diameter | Not documented | 2.85 mm[2] |
| Hotend & Nozzle | ||
| Max nozzle temp claimed AND firmware max temp limit (both values) | Not documented | 340 °C maximum with the high-temperature print core (manufacturer claim)[2] |
| Filament Handling & Detection | ||
| Spool holder location & max spool size; drybox compatibility | Not documented | Automatic climate-controlled material handling and storage station holding humidity below 15%, storing up to six spools[2] |
| Cooling & Air Handling | ||
| Chamber/exhaust fan & filtration (activated carbon / HEPA) | Not documented | HEPA filter[2] |
| Electronics & Power | ||
| Input voltage (110/220 V, switch or auto) | 100-132 V / 15 A or 200-240 V / 7 A, 50/60 Hz[1] | Not documented |
| Firmware & Openness | ||
| Firmware base & current version (Klipper fork / Marlin fork / proprietary) | Proprietary Stratasys firmware; print preparation is GrabCAD Print. The F370 additionally carries an Insight software licence and DoD STIG compliance powered by Red Hat Enterprise Linux[1] | Not documented |
| Connectivity, UI & Camera | ||
| WiFi (band/standard), Ethernet, USB ports, SD/flash-drive | Wired TCP/IP at 100 Mbps minimum, 100base-T Ethernet, RJ45. Wireless-ready IEEE 802.11 n/g/b with WPA2-PSK or 802.1x EAP, CCMP/TKIP encryption[1] | Not documented |
| Materials Support | ||
| Officially supported filament list | PLA, ABS-ESD7, ABS-M30, ASA, Diran 410MF072, FDM TPU 92A, PC-ABS, ABS-CF10, with QSR soluble support. Diran and PLA use breakaway rather than soluble support[1] | UltiMaker-branded PPS CF, PLA, Tough PLA, Nylon, PETG, PET CF and PVA, plus validated third-party materials from BASF Forward AM, Kimya, Polymaker, LEHVOSS and Jabil[2] |
| Safety | ||
| Certifications (UL/ETL/CE/FCC — verify, don't assume) | CE (low-voltage and EMC directives), FCC, EAC, cTUVus, KC, RoHS, WEEE, REACH, RCM[1] | Not documented |
| Noise & Power Consumption | ||
| Noise: claimed dB and independently measured dB (distance/method) | 46 dB maximum during build, 35 dB idle — manufacturer specification, no distance or method stated, and not an independent measurement[1] | Not documented |
| Independently Measured Performance | ||
| Dimensional accuracy measurements (third-party, with numbers) | Parts produced within +/-0.200 mm or +/-0.002 mm/mm, whichever is greater. Manufacturer figure derived from statistical data at 95% dimensional yield; Z accuracy carries an extra -0.000/+slice-height tolerance[1] | Dimensional accuracy within +/-0.2 mm or +/-0.2% of feature nominal length; UltiMaker states it tested over 95% print-completion success. Manufacturer figures, not independent measurements[2] |
Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.
Sources for this comparison
- Stratasys F123 Series product specification sheet (PSS_FDM_F123Series_0721a, PDF) stratasys.com · 2026-08 · doc
- UltiMaker Factor 4: technical specifications and pricing 3dprintingindustry.com · 2026-08 · review