3D Printing InfoPrinter comparison
FlashForge Creator 4 vs Raise3D Pro3
Compare hardware, build volume, printing specifications, dated prices and sources.
2 selected · all documented properties
Open these two in the interactive comparisonMore FlashForge Creator 4 comparisonsMore Raise3D Pro3 comparisons
| Property | FlashForge Creator 4IDEX | Raise3D Pro3IDEX |
|---|---|---|
| Identity | ||
| Brand | FlashForge | Raise3D |
| Class | IDEX | IDEX |
| Identity & Market | ||
| Manufacturer & exact marketed model name (verify the exact product identity first) | Flashforge Creator 4, sold in A and S configurations (Creator 4A, Creator 4S)[1] | Raise3D Pro3 3D Printer[2][3] |
| Street price (USD; dated snapshot per entry) | $10,999.00 at Top 3D Shop with a 2-3 week lead time, checked Aug 2026[1] | $2,999.00 on Raise3D's own store, available, checked Aug 2026[3] |
| Variants & sibling models — and how to tell them apart (spec-contamination risk) | Two factory configurations that share the chassis but not the temperature ceiling: Creator 4A ships 2 x HT extruders (320 °C max, no composite support), Creator 4S ships 1 x HT + 1 x HS (360 °C max, supports PA-CF, PA-GF, PP-CF, PPS-CF). A third extruder type, F, is rated 265 °C and intended for flexibles. Any published "360 °C" figure applies only to the HS head[1] | A crowded family with materially different prices: Pro3 $2,999, Pro3 Hyper Speed Package $4,999, Pro3 HS $4,599, Pro3 Plus HS $6,099. Build volume also changes with head count: 300 x 300 x 300 mm single-head, 255 x 300 x 300 mm dual-head. Raise3D's smaller E-series (E2 $1,999, E2CF $2,499, E3 $2,499) and the resin DF2 line are separate machines entirely[3][4][2] |
| Physical & Frame | ||
| Build volume X×Y×Z (mm) — advertised vs actually usable | 400 x 350 x 500 mm[1] | 300 x 300 x 300 mm with one extruder; 255 x 300 x 300 mm with both[2] |
| Machine footprint (mm) & clearance needed (cable/spool overhang) | 840 x 675 x 1000 mm (1050 mm on the stand). FlashForge specifies an installation space of at least 1400 x 1500 x 1600 mm[1] | 620 x 626 x 760 mm[2] |
| Net weight (kg) | 90 kg net[1] | 52.5 kg net[2] |
| Frame construction & material | Fully enclosed professional chassis on a stand[1] | Fully assembled enclosed professional chassis[2] |
| Enclosure: open / enclosed; panel material; door/lid | Fully enclosed with HEPA 13 filtration and an actively controlled chamber[1] | Enclosed with a HEPA and activated-charcoal filter[2] |
| Passive chamber temperature reached (if enclosed; measured values preferred) | Up to 65 °C, actively controlled (manufacturer claim)[1] | Not documented |
| Kinematics & Motion Hardware | ||
| Kinematics (bedslinger i3 / CoreXY / other) | IDEX — two independently driven extruders on the same gantry[1] | Dual-head with an electronic lifting system[2] |
| Speed & Acceleration | ||
| Max print speed (claimed, mm/s) | 10-200 mm/s, adjustable per material. On the 4S the HS head is quoted 100-150 mm/s and the HT head 100-200 mm/s (manufacturer figures)[1] | Not documented |
| Max travel speed | Not documented | Print-head travel speed 30-150 mm/s (manufacturer figure)[2] |
| Extruder | ||
| Type (direct drive / bowden) & design name | Direct drive, two independent extruders, interchangeable modules (F / HT / HS)[1] | Dual print heads, 1.75 mm filament[2] |
| Hotend & Nozzle | ||
| Max nozzle temp claimed AND firmware max temp limit (both values) | Depends on the fitted extruder module: F 265 °C, HT 320 °C, HS 360 °C[1] | 300 °C maximum nozzle temperature[2] |
| Stock nozzle size & sizes included in box | 0.4 mm default; 0.6 and 0.8 mm optional[1] | 0.4 mm default; 0.2, 0.6, 0.8 and 1.0 mm available[2] |
| Heated Bed & Surface | ||
| Max bed temp claimed AND firmware limit | 130 °C maximum (manufacturer claim)[1] | 120 °C maximum build-plate temperature, silicone heater[2] |
| Bed surface (material, texture, coating), single/double-sided | Not documented | Flexible steel plate with BuildTak[2] |
| Leveling & Z-Offset | ||
| Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe) | Automatic bed levelling; FlashForge does not name the probe technology in this spec table[1] | Mesh levelling with flatness detection[2] |
| Filament Handling & Detection | ||
| Spool holder location & max spool size; drybox compatibility | Two spool bays, 1 kg and 2 kg capacity[1] | Not documented |
| Cooling & Air Handling | ||
| Chamber/exhaust fan & filtration (activated carbon / HEPA) | Not documented | HEPA filter with activated charcoal[2] |
| Electronics & Power | ||
| Mainboard model & MCU (exact chip markings if teardowns exist) | Not documented | Motion controller Atmel ARM Cortex-M4 at 120 MHz with FPU; logic controller NXP ARM Cortex-A9 quad-core at 1 GHz[2] |
| Host computer (SoC, RAM, storage) if firmware runs on embedded Linux | Not documented | 1 GB RAM, 8 GB onboard flash, embedded Linux[2] |
| Input voltage (110/220 V, switch or auto) | AC 100-130 V / 200-240 V, 50-60 Hz, 30 A overcurrent protection[1] | 100-240 V AC, 50/60 Hz input; 24 V DC, 600 W output[2] |
| Total rated power draw | 2320 W rated[1] | 600 W output[2] |
| Firmware & Openness | ||
| Firmware base & current version (Klipper fork / Marlin fork / proprietary) | Not named; the supported slicer is FlashPrint[1] | Embedded Linux on the logic controller; slicing is ideaMaker. Firmware base not published[2] |
| Connectivity, UI & Camera | ||
| Display: size, type, touch? | 7-inch touchscreen, 1024 x 600[1] | 7-inch touchscreen, 1024 x 600[2] |
| WiFi (band/standard), Ethernet, USB ports, SD/flash-drive | USB flash drive, Ethernet, Wi-Fi[1] | Wi-Fi, Ethernet, USB 2.0 x2; live camera[2] |
| Camera: built-in / optional? Resolution & framerate (verify — marketing often omits real fps) | Not documented | Live camera fitted; resolution not published[2] |
| Materials Support | ||
| Officially supported filament list | Standard and engineering plastics on the HT head; the HS head adds PA-CF, PA-GF, PP-CF and PPS-CF. Materials such as PC, PA and carbon fibre are the stated targets for the 130 °C bed[1] | PLA, ABS, HIPS, PC, TPU, TPE, PETG, ASA, PP, PVA, nylon, composites and metal/wood-filled grades[2] |
| Noise & Power Consumption | ||
| Noise: claimed dB and independently measured dB (distance/method) | Not documented | Under 55 dB(A) while printing, manufacturer figure. No independent measurement; distance and method not stated[2] |
| Reliability, Support & Ecosystem | ||
| Warranty length & support reputation (evidence, not vibes) | 12 months on the printer, 3 months on extruder parts[1] | Not documented |
| Independently Measured Performance | ||
| Dimensional accuracy measurements (third-party, with numbers) | Not documented | XYZ step size 0.78125 / 0.78125 / 0.078125 micron (manufacturer specification, not an accuracy measurement)[2] |
Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.
Sources for this comparison
- Flashforge Creator 4 (A/S) product listing with full spec table top3dshop.com · 2026-08 · vendor
- Raise3D Pro3 3D Printer listing matterhackers.com · 2026-08 · vendor
- Raise3D 3D-printer collection product feed (live prices) shop.raise3d.com · 2026-08 · vendor
- Raise3D E2 3D Printer product page shop.raise3d.com · 2026-08 · vendor