3D Printing InfoPrinter comparison
FlashForge Creator 4 vs Markforged Onyx One
Compare hardware, build volume, printing specifications, dated prices and sources.
2 selected · all documented properties
Open these two in the interactive comparisonMore FlashForge Creator 4 comparisonsMore Markforged Onyx One comparisons
| Property | FlashForge Creator 4IDEX | Markforged Onyx OneINDUSTRIAL |
|---|---|---|
| Identity | ||
| Brand | FlashForge | Markforged |
| Class | IDEX | INDUSTRIAL |
| Identity & Market | ||
| Manufacturer & exact marketed model name (verify the exact product identity first) | Flashforge Creator 4, sold in A and S configurations (Creator 4A, Creator 4S)[1] | Markforged Onyx One Desktop 3D Printer[2] |
| Street price (USD; dated snapshot per entry) | $10,999.00 at Top 3D Shop with a 2-3 week lead time, checked Aug 2026[1] | Not documented |
| Variants & sibling models — and how to tell them apart (spec-contamination risk) | Two factory configurations that share the chassis but not the temperature ceiling: Creator 4A ships 2 x HT extruders (320 °C max, no composite support), Creator 4S ships 1 x HT + 1 x HS (360 °C max, supports PA-CF, PA-GF, PP-CF, PPS-CF). A third extruder type, F, is rated 265 °C and intended for flexibles. Any published "360 °C" figure applies only to the HS head[1] | The defining limitation: the Onyx One prints Onyx only and has NO continuous-fibre reinforcement. The Onyx Pro adds fibreglass, the Mark Two adds the full continuous-fibre range, and the X7 is a much larger industrial machine. Onyx One specifications must never be read from Mark Two or X-series material lists[2][3][4] |
| Physical & Frame | ||
| Build volume X×Y×Z (mm) — advertised vs actually usable | 400 x 350 x 500 mm[1] | 12.6 x 5.2 x 6.1 in (approximately 320 x 132 x 155 mm)[2] |
| Machine footprint (mm) & clearance needed (cable/spool overhang) | 840 x 675 x 1000 mm (1050 mm on the stand). FlashForge specifies an installation space of at least 1400 x 1500 x 1600 mm[1] | Not documented |
| Net weight (kg) | 90 kg net[1] | Not documented |
| Frame construction & material | Fully enclosed professional chassis on a stand[1] | Not documented |
| Enclosure: open / enclosed; panel material; door/lid | Fully enclosed with HEPA 13 filtration and an actively controlled chamber[1] | Enclosed desktop cabinet[2] |
| Passive chamber temperature reached (if enclosed; measured values preferred) | Up to 65 °C, actively controlled (manufacturer claim)[1] | Not documented |
| Kinematics & Motion Hardware | ||
| Kinematics (bedslinger i3 / CoreXY / other) | IDEX — two independently driven extruders on the same gantry[1] | Not documented |
| Speed & Acceleration | ||
| Max print speed (claimed, mm/s) | 10-200 mm/s, adjustable per material. On the 4S the HS head is quoted 100-150 mm/s and the HT head 100-200 mm/s (manufacturer figures)[1] | Not documented |
| Extruder | ||
| Type (direct drive / bowden) & design name | Direct drive, two independent extruders, interchangeable modules (F / HT / HS)[1] | Single extruder — plastic only, no fibre channel[2] |
| Hotend & Nozzle | ||
| Max nozzle temp claimed AND firmware max temp limit (both values) | Depends on the fitted extruder module: F 265 °C, HT 320 °C, HS 360 °C[1] | Not documented |
| Stock nozzle size & sizes included in box | 0.4 mm default; 0.6 and 0.8 mm optional[1] | Not documented |
| Heated Bed & Surface | ||
| Max bed temp claimed AND firmware limit | 130 °C maximum (manufacturer claim)[1] | Not documented |
| Leveling & Z-Offset | ||
| Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe) | Automatic bed levelling; FlashForge does not name the probe technology in this spec table[1] | Not documented |
| Filament Handling & Detection | ||
| Spool holder location & max spool size; drybox compatibility | Two spool bays, 1 kg and 2 kg capacity[1] | Not documented |
| Electronics & Power | ||
| Input voltage (110/220 V, switch or auto) | AC 100-130 V / 200-240 V, 50-60 Hz, 30 A overcurrent protection[1] | Not documented |
| Total rated power draw | 2320 W rated[1] | Not documented |
| Firmware & Openness | ||
| Firmware base & current version (Klipper fork / Marlin fork / proprietary) | Not named; the supported slicer is FlashPrint[1] | Proprietary; slicing and print management run in Markforged's cloud-based Eiger software[2] |
| Connectivity, UI & Camera | ||
| Display: size, type, touch? | 7-inch touchscreen, 1024 x 600[1] | Not documented |
| WiFi (band/standard), Ethernet, USB ports, SD/flash-drive | USB flash drive, Ethernet, Wi-Fi[1] | Not documented |
| Materials Support | ||
| Officially supported filament list | Standard and engineering plastics on the HT head; the HS head adds PA-CF, PA-GF, PP-CF and PPS-CF. Materials such as PC, PA and carbon fibre are the stated targets for the 130 °C bed[1] | Onyx only — Markforged's nylon filled with chopped carbon fibre. Markforged claims parts 1.4x stronger than ABS and heat deflection to 293 °F (145 °C)[2] |
| Reliability, Support & Ecosystem | ||
| Warranty length & support reputation (evidence, not vibes) | 12 months on the printer, 3 months on extruder parts[1] | Not documented |
Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.
Sources for this comparison
- Flashforge Creator 4 (A/S) product listing with full spec table top3dshop.com · 2026-08 · vendor
- Markforged Onyx One desktop composite 3D printer listing exbuild.com · 2026-08 · vendor
- Markforged Mark Two (Gen 2) specification page aniwaa.com · 2026-08 · doc
- Markforged X7 (Gen 2) specification page aniwaa.com · 2026-08 · doc