3D Printing InfoPrinter comparison
ELEGOO Neptune 4 vs Stratasys F270
Compare hardware, build volume, printing specifications, dated prices and sources.
2 selected · all documented properties
Open these two in the interactive comparisonMore ELEGOO Neptune 4 comparisonsMore Stratasys F270 comparisons
| Property | ELEGOO Neptune 4BEDSLINGER | Stratasys F270INDUSTRIAL |
|---|---|---|
| Identity | ||
| Brand | ELEGOO | Stratasys |
| Class | BEDSLINGER | INDUSTRIAL |
| Identity & Market | ||
| Manufacturer & exact marketed model name (verify the exact product identity first) | ELEGOO Neptune 4 (spec table "Product Model: Neptune 4")[1] | Stratasys F270, part of the Stratasys F123 Series[2] |
| Release date (announcement and actual shipping) | Listed on the ELEGOO US store from 27 May 2023 (Shopify publish date)[3] | The F123 series spec sheet carried is revision 0721a (July 2021). Stratasys does not print a launch date on it[2] |
| Street price (USD; dated snapshot per entry) | $219.00 on us.elegoo.com, Aug 2026, against a compare-at price of $249.00; both the Ribbon-Cable and Type-C printhead variants are the same price[3] | Not documented |
| Variants & sibling models — and how to tell them apart (spec-contamination risk) | Two printhead variants of the same machine are sold under one SKU - "Ribbon-Cable Version" and "Type-C Version" - which use different printhead parts. Within the Neptune 4 family the numbers diverge sharply and get mixed up constantly: Neptune 4 is 225 x 225 x 265 mm with a 110 C bed and 20000 mm/s2; the Plus is 320 x 320 x 385 mm with a 100 C bed and 12000 mm/s2; the Max is 420 x 420 x 480 mm with an 85 C bed and only 8000 mm/s2. The Neptune 4 Pro is a separate model again[3][1][4][5] | Middle of the full-cabinet trio. Same materials as the F170 but a larger build size; the F370 adds ABS-ESD7, PC-ABS and Diran 410MF07 and is the only model with Insight and DoD STIG compliance. All three full-cabinet models share the same 1,626 x 864 x 711 mm footprint and 227 kg weight[2] |
| Market position: superseded? successor announced? | Still listed in ELEGOO's US store Neptune section in Aug 2026 alongside the 4 Pro, 4 Plus and 4 Max, but ELEGOO's current development is on the Centauri line[6] | Not documented |
| Physical & Frame | ||
| Build volume X×Y×Z (mm) — advertised vs actually usable | 225 x 225 x 265 mm; the PEI platform itself is 235 x 235 mm[1] | 305 x 254 x 305 mm (12 x 10 x 12 in)[2] |
| Machine footprint (mm) & clearance needed (cable/spool overhang) | 475 x 445 x 515 mm. ELEGOO separately publishes a "maximum size for machine activity" of 475 x 550 x 735 mm including rack and tray - the depth to allow for is 550 mm, not 445 mm[1] | 1,626 x 864 x 711 mm (64 x 34 x 28 in)[2] |
| Net weight (kg) | 8.3 kg net, 10.6 kg gross[1] | 124 kg (F120) or 227 kg with consumables (F170, F270, F370)[2] |
| Frame construction & material | CNC-machined aluminium extrusion frame[1] | Fully enclosed office/classroom-grade cabinet, factory assembled[2] |
| Enclosure: open / enclosed; panel material; door/lid | Open frame, no enclosure[1] | Enclosed build chamber[2] |
| Kinematics & Motion Hardware | ||
| Kinematics (bedslinger i3 / CoreXY / other) | Cartesian i3 bed-slinger[1] | Not documented |
| Z-axis: leadscrew count & type, sync mechanism, anti-backlash | Two lead screws (the Neptune 4 Plus and Max add two tie rods to the same arrangement)[7] | Not documented |
| Stepper drivers (exact model e.g. TMC2209; UART/SPI; sensorless homing?) | "Silent Drive (All Axes)" is all ELEGOO publishes; no driver part number is given[7] | Not documented |
| Speed & Acceleration | ||
| Max print speed (claimed, mm/s) | 500 mm/s max toolhead speed (manufacturer claim); the Neptune 4 Plus page for the same family states a recommended 250 mm/s[1][4] | Not documented |
| Recommended/typical print speed | 250 mm/s recommended printing speed against the 500 mm/s ceiling (ELEGOO's own figure)[7] | Not documented |
| Max acceleration (claimed, mm/s²) | 20000 mm/s2 max toolhead acceleration (manufacturer claim) - notably higher than the Plus at 12000 and the Max at 8000, because the moving mass is smaller[1][4][5] | Not documented |
| Extruder | ||
| Type (direct drive / bowden) & design name | Dual-gear direct extruder with 2 fans[7] | Not documented |
| Hotend & Nozzle | ||
| Hotend design (proprietary/standard; quick-swap mechanism?) | Brass nozzle, 0.4 mm, with a copper and titanium-alloy heat break - the Plus and Max use a titanium-alloy heat break only[7] | Not documented |
| Max nozzle temp claimed AND firmware max temp limit (both values) | 300 C claimed max nozzle temperature[1] | Not documented |
| Heated Bed & Surface | ||
| Max bed temp claimed AND firmware limit | 110 C max heated bed temperature[1] | Not documented |
| Bed surface (material, texture, coating), single/double-sided | PEI spring steel sheet, now upgraded by ELEGOO to a dual-sided textured PEI + PLA-specific surface[7] | Not documented |
| Leveling & Z-Offset | ||
| Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe) | Manual levelling combined with 121-point auto-levelling; no full-auto calibration on this model[7] | Not documented |
| Filament Handling & Detection | ||
| Filament runout sensor (type, location) | Filament detection fitted; power-loss resume printing supported[1] | Not documented |
| Electronics & Power | ||
| Mainboard model & MCU (exact chip markings if teardowns exist) | ELEGOO describes it only as a "Klipper High-Speed Quiet Motherboard" - no board model or MCU published[7] | Not documented |
| Input voltage (110/220 V, switch or auto) | 115/230 V, 50/60 Hz on the product page; ELEGOO's compare page gives 110-120 / 220-240 VAC 50/60 Hz[1][7] | 100-132 V / 15 A or 200-240 V / 7 A, 50/60 Hz[2] |
| Total rated power draw | 310 W rated power, 24 V output[7] | Not documented |
| Firmware & Openness | ||
| Firmware base & current version (Klipper fork / Marlin fork / proprietary) | Klipper (ELEGOO names the system "Klipper" outright for the Neptune 4 series, rather than the ELEGOO OS branding used on the Centauri machines)[7][8] | Proprietary Stratasys firmware; print preparation is GrabCAD Print. The F370 additionally carries an Insight software licence and DoD STIG compliance powered by Red Hat Enterprise Linux[2] |
| Connectivity, UI & Camera | ||
| Display: size, type, touch? | 4.3-inch colour capacitive touch screen[7] | Not documented |
| On-device UI capabilities (model preview, per-object controls, etc.) | Colour capacitive touch UI; ElegooSlicer recommended, with Orca and Cura also supported[7] | Not documented |
| WiFi (band/standard), Ethernet, USB ports, SD/flash-drive | LAN and USB file transfer; no Wi-Fi is listed for the base Neptune 4, unlike the Plus (USB/LAN/Wi-Fi) and Max (Wi-Fi/USB/WLAN)[1][4][5] | Wired TCP/IP at 100 Mbps minimum, 100base-T Ethernet, RJ45. Wireless-ready IEEE 802.11 n/g/b with WPA2-PSK or 802.1x EAP, CCMP/TKIP encryption[2] |
| Materials Support | ||
| Officially supported filament list | PLA, TPU, PETG, ABS, ASA, Nylon[1] | PLA, ABS-M30, ASA, FDM TPU 92A, ABS-CF10, with QSR soluble support[2] |
| Safety | ||
| Certifications (UL/ETL/CE/FCC — verify, don't assume) | Not documented | CE (low-voltage and EMC directives), FCC, EAC, cTUVus, KC, RoHS, WEEE, REACH, RCM[2] |
| Noise & Power Consumption | ||
| Noise: claimed dB and independently measured dB (distance/method) | Operating sound published as 60 dB or less - a manufacturer figure with no distance or method stated, so it is not comparable with an independently measured reading[7] | 46 dB maximum during build, 35 dB idle — manufacturer specification, no distance or method stated, and not an independent measurement[2] |
| Reliability, Support & Ecosystem | ||
| Warranty length & support reputation (evidence, not vibes) | 12 months on brand-new machines and parts, but ELEGOO's own table excludes a long list of parts from that: PEI plate / build plate / nozzle kit / PTFE tube / heater / thermistor / hot end / packaging / manual / tools carry no warranty at all, and the extruder, extruder kit and printhead kit get 6 months. Certified pre-owned machines carry no warranty[9] | Not documented |
| Independently Measured Performance | ||
| Dimensional accuracy measurements (third-party, with numbers) | Not documented | Parts produced within +/-0.200 mm or +/-0.002 mm/mm, whichever is greater. Manufacturer figure derived from statistical data at 95% dimensional yield; Z accuracy carries an extra -0.000/+slice-height tolerance[2] |
Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.
Sources for this comparison
- ELEGOO Neptune 4 product page (Specification table) us.elegoo.com · 2026-08 · vendor
- Stratasys F123 Series product specification sheet (PSS_FDM_F123Series_0721a, PDF) stratasys.com · 2026-08 · doc
- ELEGOO Neptune 4 Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Plus product page (full specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Max product page (Specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO US store 3D printers collection (current line-up, Aug 2026) us.elegoo.com · 2026-08 · vendor
- ELEGOO compare-products page, which embeds the full per-model specification JSON for every Neptune, Centauri and OrangeStorm machine us.elegoo.com · 2026-08 · vendor
- ELEGOO Centauri Carbon product page (full specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Refund & Warranty policy (warranty period table) us.elegoo.com · 2026-08 · vendor