3D Printing InfoPrinter comparison
ELEGOO Neptune 4 vs Sovol SV08 Max
Compare hardware, build volume, printing specifications, dated prices and sources.
2 selected · all documented properties
Open these two in the interactive comparisonMore ELEGOO Neptune 4 comparisonsMore Sovol SV08 Max comparisons
| Property | ELEGOO Neptune 4BEDSLINGER | Sovol SV08 MaxCOREXY |
|---|---|---|
| Identity | ||
| Brand | ELEGOO | Sovol |
| Class | BEDSLINGER | COREXY |
| Identity & Market | ||
| Manufacturer & exact marketed model name (verify the exact product identity first) | ELEGOO Neptune 4 (spec table "Product Model: Neptune 4")[1] | Sovol SV08 Max 3D Printer[2][3] |
| Release date (announcement and actual shipping) | Listed on the ELEGOO US store from 27 May 2023 (Shopify publish date)[4] | Not documented |
| Street price (USD; dated snapshot per entry) | $219.00 on us.elegoo.com, Aug 2026, against a compare-at price of $249.00; both the Ribbon-Cable and Type-C printhead variants are the same price[4] | $1,099.00 on sovol3d.com against a $1,299.00 compare-at price (15% off), in stock, checked Aug 2026[2][3] |
| Variants & sibling models — and how to tell them apart (spec-contamination risk) | Two printhead variants of the same machine are sold under one SKU - "Ribbon-Cable Version" and "Type-C Version" - which use different printhead parts. Within the Neptune 4 family the numbers diverge sharply and get mixed up constantly: Neptune 4 is 225 x 225 x 265 mm with a 110 C bed and 20000 mm/s2; the Plus is 320 x 320 x 385 mm with a 100 C bed and 12000 mm/s2; the Max is 420 x 420 x 480 mm with an 85 C bed and only 8000 mm/s2. The Neptune 4 Pro is a separate model again[4][1][5][6] | Much larger sibling of the SV08. Differences that matter in a spec box: 500x500x500 vs 350x350x345, 50 vs 30 mm3/s, TMC5160 XY drivers vs TMC2209, CAN bus, HDMI output, dual 0.4 mm nozzles in the box, and a separately sold chamber-heating module. A chamber heating module for the SV08 Max is listed at $69[2][7][8][3] |
| Market position: superseded? successor announced? | Still listed in ELEGOO's US store Neptune section in Aug 2026 alongside the 4 Pro, 4 Plus and 4 Max, but ELEGOO's current development is on the Centauri line[9] | Not documented |
| Physical & Frame | ||
| Build volume X×Y×Z (mm) — advertised vs actually usable | 225 x 225 x 265 mm; the PEI platform itself is 235 x 235 mm[1] | 500 x 500 x 500 mm advertised[2][7] |
| Machine footprint (mm) & clearance needed (cable/spool overhang) | 475 x 445 x 515 mm. ELEGOO separately publishes a "maximum size for machine activity" of 475 x 550 x 735 mm including rack and tray - the depth to allow for is 550 mm, not 445 mm[1] | 700 x 710 x 750 mm excluding the spool holder. Shipping cartons: 810 x 820 x 360 mm plus a 775 x 728 x 155 mm enclosure-kit box[2][7] |
| Net weight (kg) | 8.3 kg net, 10.6 kg gross[1] | Not documented |
| Frame construction & material | CNC-machined aluminium extrusion frame[1] | Aluminium-extrusion CoreXY frame supplied as a kit; Sovol ships it in two cartons, one of which is an enclosure kit[2] |
| Enclosure: open / enclosed; panel material; door/lid | Open frame, no enclosure[1] | Enclosure kit shipped with the machine (separate carton). A chamber-heating module is sold separately at $69[2][3] |
| Kinematics & Motion Hardware | ||
| Kinematics (bedslinger i3 / CoreXY / other) | Cartesian i3 bed-slinger[1] | CoreXY[2][7] |
| Z-axis: leadscrew count & type, sync mechanism, anti-backlash | Two lead screws (the Neptune 4 Plus and Max add two tie rods to the same arrangement)[10] | Not documented |
| Stepper drivers (exact model e.g. TMC2209; UART/SPI; sensorless homing?) | "Silent Drive (All Axes)" is all ELEGOO publishes; no driver part number is given[10] | Z axis 4 x TMC2209; A axis 1 x TMC5160; B axis 1 x TMC5160. Toolhead communication over CAN bus[2][7] |
| Speed & Acceleration | ||
| Max print speed (claimed, mm/s) | 500 mm/s max toolhead speed (manufacturer claim); the Neptune 4 Plus page for the same family states a recommended 250 mm/s[1][5] | 700 mm/s maximum (manufacturer claim)[2][7] |
| Recommended/typical print speed | 250 mm/s recommended printing speed against the 500 mm/s ceiling (ELEGOO's own figure)[10] | Not documented |
| Max acceleration (claimed, mm/s²) | 20000 mm/s2 max toolhead acceleration (manufacturer claim) - notably higher than the Plus at 12000 and the Max at 8000, because the moving mass is smaller[1][5][6] | 40,000 mm/s2 maximum (manufacturer claim)[2][7] |
| Max volumetric flow claimed (mm³/s) | Not documented | 50 mm3/s maximum (manufacturer claim)[2][7] |
| Extruder | ||
| Type (direct drive / bowden) & design name | Dual-gear direct extruder with 2 fans[10] | Direct drive with auxiliary (assisted) filament feeding[2][7] |
| Hotend & Nozzle | ||
| Hotend design (proprietary/standard; quick-swap mechanism?) | Brass nozzle, 0.4 mm, with a copper and titanium-alloy heat break - the Plus and Max use a titanium-alloy heat break only[10] | Ceramic heater. Two 0.4 mm nozzles supplied as standard; 0.4/0.6/0.8 mm optional[2][7] |
| Max nozzle temp claimed AND firmware max temp limit (both values) | 300 C claimed max nozzle temperature[1] | <=300 °C claimed[2][7] |
| Heated Bed & Surface | ||
| Max bed temp claimed AND firmware limit | 110 C max heated bed temperature[1] | <=100 °C claimed[2][7] |
| Bed surface (material, texture, coating), single/double-sided | PEI spring steel sheet, now upgraded by ELEGOO to a dual-sided textured PEI + PLA-specific surface[10] | Not documented |
| Leveling & Z-Offset | ||
| Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe) | Manual levelling combined with 121-point auto-levelling; no full-auto calibration on this model[10] | Not stated on the SV08 Max page; the SV08 family uses an inductive sensor plus pressure sensor[2] |
| Filament Handling & Detection | ||
| Filament runout sensor (type, location) | Filament detection fitted; power-loss resume printing supported[1] | Filament runout detection plus filament tangle/clog detection. Sovol does not describe the tangle or clog mechanism[2][7] |
| Electronics & Power | ||
| Mainboard model & MCU (exact chip markings if teardowns exist) | ELEGOO describes it only as a "Klipper High-Speed Quiet Motherboard" - no board model or MCU published[10] | Not documented |
| Host computer (SoC, RAM, storage) if firmware runs on embedded Linux | Not documented | 1 GB RAM (512 MB + 512 MB), 8 GB eMMC[2][7] |
| Input voltage (110/220 V, switch or auto) | 115/230 V, 50/60 Hz on the product page; ELEGOO's compare page gives 110-120 / 220-240 VAC 50/60 Hz[1][10] | Not documented |
| Total rated power draw | 310 W rated power, 24 V output[10] | Not documented |
| Firmware & Openness | ||
| Firmware base & current version (Klipper fork / Marlin fork / proprietary) | Klipper (ELEGOO names the system "Klipper" outright for the Neptune 4 series, rather than the ELEGOO OS branding used on the Centauri machines)[10][11] | Klipper (3DJake's table renders it as "Clipper"). OrcaSlicer is the supported slicer[2][7] |
| Connectivity, UI & Camera | ||
| Display: size, type, touch? | 4.3-inch colour capacitive touch screen[10] | Not documented |
| On-device UI capabilities (model preview, per-object controls, etc.) | Colour capacitive touch UI; ElegooSlicer recommended, with Orca and Cura also supported[10] | Not documented |
| WiFi (band/standard), Ethernet, USB ports, SD/flash-drive | LAN and USB file transfer; no Wi-Fi is listed for the base Neptune 4, unlike the Plus (USB/LAN/Wi-Fi) and Max (Wi-Fi/USB/WLAN)[1][5][6] | USB, Wi-Fi 2.4 GHz and 5 GHz, HDMI, Ethernet[2][7] |
| Power-Loss & Interruption Recovery | ||
| Power-loss recovery: mechanism (how is state saved? capacitor / eeprom / file on shutdown?) | Not documented | Power-loss resume printing supported; mechanism not published[2][7] |
| Materials Support | ||
| Officially supported filament list | PLA, TPU, PETG, ABS, ASA, Nylon[1] | 1.75 mm filament; Sovol does not publish a per-material list on this page[2][7] |
| Noise & Power Consumption | ||
| Noise: claimed dB and independently measured dB (distance/method) | Operating sound published as 60 dB or less - a manufacturer figure with no distance or method stated, so it is not comparable with an independently measured reading[10] | Not documented |
| Reliability, Support & Ecosystem | ||
| Warranty length & support reputation (evidence, not vibes) | 12 months on brand-new machines and parts, but ELEGOO's own table excludes a long list of parts from that: PEI plate / build plate / nozzle kit / PTFE tube / heater / thermistor / hot end / packaging / manual / tools carry no warranty at all, and the extruder, extruder kit and printhead kit get 6 months. Certified pre-owned machines carry no warranty[12] | Not documented |
Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.
Sources for this comparison
- ELEGOO Neptune 4 product page (Specification table) us.elegoo.com · 2026-08 · vendor
- Sovol SV08 Max 3D Printer product page sovol3d.com · 2026-08 · vendor
- Sovol 3D-printer collection product feed (live prices and stock) sovol3d.com · 2026-08 · vendor
- ELEGOO Neptune 4 Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Plus product page (full specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Max product page (Specification table) us.elegoo.com · 2026-08 · vendor
- Sovol SV08 Max technical data table 3djake.com · 2026-08 · vendor
- Sovol SV08 3D Printer product page sovol3d.com · 2026-08 · vendor
- ELEGOO US store 3D printers collection (current line-up, Aug 2026) us.elegoo.com · 2026-08 · vendor
- ELEGOO compare-products page, which embeds the full per-model specification JSON for every Neptune, Centauri and OrangeStorm machine us.elegoo.com · 2026-08 · vendor
- ELEGOO Centauri Carbon product page (full specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Refund & Warranty policy (warranty period table) us.elegoo.com · 2026-08 · vendor