3D Printing InfoPrinter comparison
ELEGOO Neptune 4 vs INTAMSYS FUNMAT PRO 610 HT
Compare hardware, build volume, printing specifications, dated prices and sources.
2 selected · all documented properties
Open these two in the interactive comparisonMore ELEGOO Neptune 4 comparisonsMore INTAMSYS FUNMAT PRO 610 HT comparisons
| Property | ELEGOO Neptune 4BEDSLINGER | INTAMSYS FUNMAT PRO 610 HTINDUSTRIAL |
|---|---|---|
| Identity | ||
| Brand | ELEGOO | INTAMSYS |
| Class | BEDSLINGER | INDUSTRIAL |
| Identity & Market | ||
| Manufacturer & exact marketed model name (verify the exact product identity first) | ELEGOO Neptune 4 (spec table "Product Model: Neptune 4")[1] | INTAMSYS FUNMAT PRO 610 HT, a high-temperature industrial 3D printer[2] |
| Release date (announcement and actual shipping) | Listed on the ELEGOO US store from 27 May 2023 (Shopify publish date)[3] | Not documented |
| Street price (USD; dated snapshot per entry) | $219.00 on us.elegoo.com, Aug 2026, against a compare-at price of $249.00; both the Ribbon-Cable and Type-C printhead variants are the same price[3] | $139,500.00 at Top 3D Shop, reduced from $159,500.00, in stock with a 2-6 week lead time, checked Aug 2026[2] |
| Variants & sibling models — and how to tell them apart (spec-contamination risk) | Two printhead variants of the same machine are sold under one SKU - "Ribbon-Cable Version" and "Type-C Version" - which use different printhead parts. Within the Neptune 4 family the numbers diverge sharply and get mixed up constantly: Neptune 4 is 225 x 225 x 265 mm with a 110 C bed and 20000 mm/s2; the Plus is 320 x 320 x 385 mm with a 100 C bed and 12000 mm/s2; the Max is 420 x 420 x 480 mm with an 85 C bed and only 8000 mm/s2. The Neptune 4 Pro is a separate model again[3][1][4][5] | The 300 °C chamber and 300 °C build plate are what separate this from the Funmat Pro 410 (90 °C chamber, 160 °C plate) — both quote a 500 °C extruder. Three-phase power is required (380 V or 200 V), which the 410 does not need[2][6] |
| Market position: superseded? successor announced? | Still listed in ELEGOO's US store Neptune section in Aug 2026 alongside the 4 Pro, 4 Plus and 4 Max, but ELEGOO's current development is on the Centauri line[7] | Not documented |
| Physical & Frame | ||
| Build volume X×Y×Z (mm) — advertised vs actually usable | 225 x 225 x 265 mm; the PEI platform itself is 235 x 235 mm[1] | 610 x 508 x 508 mm (24 x 20 x 20 in)[2] |
| Machine footprint (mm) & clearance needed (cable/spool overhang) | 475 x 445 x 515 mm. ELEGOO separately publishes a "maximum size for machine activity" of 475 x 550 x 735 mm including rack and tray - the depth to allow for is 550 mm, not 445 mm[1] | 1710 x 1425 x 2350 mm including the warning lights[2] |
| Net weight (kg) | 8.3 kg net, 10.6 kg gross[1] | 1450 kg[2] |
| Frame construction & material | CNC-machined aluminium extrusion frame[1] | Servo control system on high-precision ball screws; liquid cooling plus fans[2] |
| Enclosure: open / enclosed; panel material; door/lid | Open frame, no enclosure[1] | Fully enclosed printing chamber with a double-layer thickened heat-insulated front door and a heat-resistant shield[2] |
| Passive chamber temperature reached (if enclosed; measured values preferred) | Not documented | Up to 300 °C chamber temperature (manufacturer specification, actively heated)[2] |
| Kinematics & Motion Hardware | ||
| Kinematics (bedslinger i3 / CoreXY / other) | Cartesian i3 bed-slinger[1] | Servo-driven ball-screw motion system; two nozzles[2] |
| Z-axis: leadscrew count & type, sync mechanism, anti-backlash | Two lead screws (the Neptune 4 Plus and Max add two tie rods to the same arrangement)[8] | Not documented |
| Stepper drivers (exact model e.g. TMC2209; UART/SPI; sensorless homing?) | "Silent Drive (All Axes)" is all ELEGOO publishes; no driver part number is given[8] | Not documented |
| Speed & Acceleration | ||
| Max print speed (claimed, mm/s) | 500 mm/s max toolhead speed (manufacturer claim); the Neptune 4 Plus page for the same family states a recommended 250 mm/s[1][4] | 160 mm/s maximum print speed (manufacturer figure). Travel: XY 400 mm/s, Z 50 mm/s[2] |
| Recommended/typical print speed | 250 mm/s recommended printing speed against the 500 mm/s ceiling (ELEGOO's own figure)[8] | Not documented |
| Max acceleration (claimed, mm/s²) | 20000 mm/s2 max toolhead acceleration (manufacturer claim) - notably higher than the Plus at 12000 and the Max at 8000, because the moving mass is smaller[1][4][5] | Not documented |
| Extruder | ||
| Type (direct drive / bowden) & design name | Dual-gear direct extruder with 2 fans[8] | Two nozzles, 1.75 mm filament[2] |
| Hotend & Nozzle | ||
| Hotend design (proprietary/standard; quick-swap mechanism?) | Brass nozzle, 0.4 mm, with a copper and titanium-alloy heat break - the Plus and Max use a titanium-alloy heat break only[8] | Not documented |
| Max nozzle temp claimed AND firmware max temp limit (both values) | 300 C claimed max nozzle temperature[1] | 500 °C maximum nozzle temperature (manufacturer specification)[2] |
| Stock nozzle size & sizes included in box | Not documented | 0.4 mm default; 0.6 and 0.8 mm optional[2] |
| Heated Bed & Surface | ||
| Max bed temp claimed AND firmware limit | 110 C max heated bed temperature[1] | Up to 300 °C heated build plate[2] |
| Bed surface (material, texture, coating), single/double-sided | PEI spring steel sheet, now upgraded by ELEGOO to a dual-sided textured PEI + PLA-specific surface[8] | Flexible build plates with a vacuum adsorption system[2] |
| Leveling & Z-Offset | ||
| Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe) | Manual levelling combined with 121-point auto-levelling; no full-auto calibration on this model[8] | Auto levelling; probe technology not named[2] |
| Filament Handling & Detection | ||
| Filament runout sensor (type, location) | Filament detection fitted; power-loss resume printing supported[1] | Not documented |
| Spool holder location & max spool size; drybox compatibility | Not documented | Four independent sealed filament chambers with active heating to 50 °C and dry compressed air; four spools up to 3 kg each[2] |
| Electronics & Power | ||
| Mainboard model & MCU (exact chip markings if teardowns exist) | ELEGOO describes it only as a "Klipper High-Speed Quiet Motherboard" - no board model or MCU published[8] | Not documented |
| Input voltage (110/220 V, switch or auto) | 115/230 V, 50/60 Hz on the product page; ELEGOO's compare page gives 110-120 / 220-240 VAC 50/60 Hz[1][8] | Three phase: 380 V 30 A/phase or 200 V 50 A/phase, 50-60 Hz[2] |
| Total rated power draw | 310 W rated power, 24 V output[8] | 15 kW maximum[2] |
| Firmware & Openness | ||
| Firmware base & current version (Klipper fork / Marlin fork / proprietary) | Klipper (ELEGOO names the system "Klipper" outright for the Neptune 4 series, rather than the ELEGOO OS branding used on the Centauri machines)[8][9] | Proprietary; slicing is INTAMSUITE (Windows only)[2] |
| Connectivity, UI & Camera | ||
| Display: size, type, touch? | 4.3-inch colour capacitive touch screen[8] | 10-inch touchscreen[2] |
| On-device UI capabilities (model preview, per-object controls, etc.) | Colour capacitive touch UI; ElegooSlicer recommended, with Orca and Cura also supported[8] | Not documented |
| WiFi (band/standard), Ethernet, USB ports, SD/flash-drive | LAN and USB file transfer; no Wi-Fi is listed for the base Neptune 4, unlike the Plus (USB/LAN/Wi-Fi) and Max (Wi-Fi/USB/WLAN)[1][4][5] | Wi-Fi, Ethernet, USB[2] |
| Materials Support | ||
| Officially supported filament list | PLA, TPU, PETG, ABS, ASA, Nylon[1] | PEI (ULTEM) 9085 and 1010, PEEK, PEEK-CF, PEEK-GF, PEKK, PPSU, PPS, PC, PC-ABS, PPA-CF, PPA-GF, PA6/66, PA6-CF, PA12, PA12-CF, ABS+, ABS, ASA and others[2] |
| Safety | ||
| Certifications (UL/ETL/CE/FCC — verify, don't assume) | Not documented | CE, FCC, SGS; safety design to EN60204[2] |
| Hardware safety: fusing, strain reliefs, belt covers, pinch points | Not documented | Independent safety PLC, electromagnetic safety door lock, over-temperature protection, overload protection, emergency stop button, three-colour warning light. Safety standard EN60204[2] |
| Noise & Power Consumption | ||
| Noise: claimed dB and independently measured dB (distance/method) | Operating sound published as 60 dB or less - a manufacturer figure with no distance or method stated, so it is not comparable with an independently measured reading[8] | Not documented |
| Reliability, Support & Ecosystem | ||
| Warranty length & support reputation (evidence, not vibes) | 12 months on brand-new machines and parts, but ELEGOO's own table excludes a long list of parts from that: PEI plate / build plate / nozzle kit / PTFE tube / heater / thermistor / hot end / packaging / manual / tools carry no warranty at all, and the extruder, extruder kit and printhead kit get 6 months. Certified pre-owned machines carry no warranty[10] | Not documented |
| Independently Measured Performance | ||
| Dimensional accuracy measurements (third-party, with numbers) | Not documented | Resolution XY 12.5 um, Z 1.25 um (manufacturer specification)[2] |
Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.
Sources for this comparison
- ELEGOO Neptune 4 product page (Specification table) us.elegoo.com · 2026-08 · vendor
- Intamsys Funmat Pro 610 HT product listing top3dshop.com · 2026-08 · vendor
- ELEGOO Neptune 4 Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Plus product page (full specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Max product page (Specification table) us.elegoo.com · 2026-08 · vendor
- Intamsys Funmat Pro 410 product listing top3dshop.com · 2026-08 · vendor
- ELEGOO US store 3D printers collection (current line-up, Aug 2026) us.elegoo.com · 2026-08 · vendor
- ELEGOO compare-products page, which embeds the full per-model specification JSON for every Neptune, Centauri and OrangeStorm machine us.elegoo.com · 2026-08 · vendor
- ELEGOO Centauri Carbon product page (full specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Refund & Warranty policy (warranty period table) us.elegoo.com · 2026-08 · vendor