3D Printing InfoPrinter comparison
ELEGOO Neptune 4 vs FlashForge Creator 5
Compare hardware, build volume, printing specifications, dated prices and sources.
2 selected · all documented properties
Open these two in the interactive comparisonMore ELEGOO Neptune 4 comparisonsMore FlashForge Creator 5 comparisons
| Property | ELEGOO Neptune 4BEDSLINGER | FlashForge Creator 5TOOLCHANGER |
|---|---|---|
| Identity | ||
| Brand | ELEGOO | FlashForge |
| Class | BEDSLINGER | TOOLCHANGER |
| Identity & Market | ||
| Manufacturer & exact marketed model name (verify the exact product identity first) | ELEGOO Neptune 4 (spec table "Product Model: Neptune 4")[1] | Flashforge Creator 5, sold as "Creator 5 4-Toolheads Multi-Color 3D Printer"[2][3] |
| Release date (announcement and actual shipping) | Listed on the ELEGOO US store from 27 May 2023 (Shopify publish date)[4] | Announced with a $10 deposit programme; shipping to deposit backers by 19 May 2026. One secondary source puts general release in early May 2026[5][6] |
| Launch MSRP (USD) | Not documented | $649 early-bird (deposit price, open until 20 June 2026); $799 standard MSRP[5][6] |
| Street price (USD; dated snapshot per entry) | $219.00 on us.elegoo.com, Aug 2026, against a compare-at price of $249.00; both the Ribbon-Cable and Type-C printhead variants are the same price[4] | $799.00 on flashforge.com, in stock, with $100 auto-applied in cart, checked Aug 2026[2][3] |
| Variants & sibling models — and how to tell them apart (spec-contamination risk) | Two printhead variants of the same machine are sold under one SKU - "Ribbon-Cable Version" and "Type-C Version" - which use different printhead parts. Within the Neptune 4 family the numbers diverge sharply and get mixed up constantly: Neptune 4 is 225 x 225 x 265 mm with a 110 C bed and 20000 mm/s2; the Plus is 320 x 320 x 385 mm with a 100 C bed and 12000 mm/s2; the Max is 420 x 420 x 480 mm with an 85 C bed and only 8000 mm/s2. The Neptune 4 Pro is a separate model again[4][1][7][8] | Paired with the Creator 5 Pro at $949, which adds a sealed enclosure, 65 °C active chamber heating and HEPA13 + carbon filtration. Motion system, 256 mm build volume, four toolheads, 600 mm/s and 30,000 mm/s2 are the same on both, so enclosure and chamber are the only reliable discriminators[2][9][5][6][3] |
| Market position: superseded? successor announced? | Still listed in ELEGOO's US store Neptune section in Aug 2026 alongside the 4 Pro, 4 Plus and 4 Max, but ELEGOO's current development is on the Centauri line[10] | Not documented |
| Physical & Frame | ||
| Build volume X×Y×Z (mm) — advertised vs actually usable | 225 x 225 x 265 mm; the PEI platform itself is 235 x 235 mm[1] | 256 x 256 x 256 mm[5][6][11] |
| Machine footprint (mm) & clearance needed (cable/spool overhang) | 475 x 445 x 515 mm. ELEGOO separately publishes a "maximum size for machine activity" of 475 x 550 x 735 mm including rack and tray - the depth to allow for is 550 mm, not 445 mm[1] | Not documented |
| Net weight (kg) | 8.3 kg net, 10.6 kg gross[1] | Not documented |
| Frame construction & material | CNC-machined aluminium extrusion frame[1] | CoreXY frame; FlashForge does not publish a frame-material breakdown and no dimensions or weight have been published for this model[5][6] |
| Enclosure: open / enclosed; panel material; door/lid | Open frame, no enclosure[1] | Open frame. No enclosure, no chamber heating and no filtration[5][6][11] |
| Kinematics & Motion Hardware | ||
| Kinematics (bedslinger i3 / CoreXY / other) | Cartesian i3 bed-slinger[1] | CoreXY with four independent toolheads on a FlashSwap changer. FlashForge claims a physical head swap in about 7 seconds[5][6][11] |
| Z-axis: leadscrew count & type, sync mechanism, anti-backlash | Two lead screws (the Neptune 4 Plus and Max add two tie rods to the same arrangement)[12] | Not documented |
| Stepper drivers (exact model e.g. TMC2209; UART/SPI; sensorless homing?) | "Silent Drive (All Axes)" is all ELEGOO publishes; no driver part number is given[12] | Not documented |
| Speed & Acceleration | ||
| Max print speed (claimed, mm/s) | 500 mm/s max toolhead speed (manufacturer claim); the Neptune 4 Plus page for the same family states a recommended 250 mm/s[1][7] | 600 mm/s maximum, reported by both secondary sources as a travel-speed figure (manufacturer claim)[5][6] |
| Recommended/typical print speed | 250 mm/s recommended printing speed against the 500 mm/s ceiling (ELEGOO's own figure)[12] | Not documented |
| Max acceleration (claimed, mm/s²) | 20000 mm/s2 max toolhead acceleration (manufacturer claim) - notably higher than the Plus at 12000 and the Max at 8000, because the moving mass is smaller[1][7][8] | 30,000 mm/s2 maximum (manufacturer claim)[5][6] |
| Extruder | ||
| Type (direct drive / bowden) & design name | Dual-gear direct extruder with 2 fans[12] | Not documented |
| Hotend & Nozzle | ||
| Hotend design (proprietary/standard; quick-swap mechanism?) | Brass nozzle, 0.4 mm, with a copper and titanium-alloy heat break - the Plus and Max use a titanium-alloy heat break only[12] | Not documented |
| Max nozzle temp claimed AND firmware max temp limit (both values) | 300 C claimed max nozzle temperature[1] | Not documented |
| Stock nozzle material (brass / hardened steel / plated copper / composite tip) | Not documented | Hardened steel nozzles as standard[5][6] |
| Heated Bed & Surface | ||
| Max bed temp claimed AND firmware limit | 110 C max heated bed temperature[1] | 120 °C maximum (manufacturer claim)[5][6] |
| Bed surface (material, texture, coating), single/double-sided | PEI spring steel sheet, now upgraded by ELEGOO to a dual-sided textured PEI + PLA-specific surface[12] | Not documented |
| Leveling & Z-Offset | ||
| Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe) | Manual levelling combined with 121-point auto-levelling; no full-auto calibration on this model[12] | Fully automatic calibration and levelling; FlashForge does not name the probe technology[2] |
| Filament Handling & Detection | ||
| Filament runout sensor (type, location) | Filament detection fitted; power-loss resume printing supported[1] | Not documented |
| Multi-material/multi-color capability or official upgrade path | Not documented | Four independent toolheads swapped physically rather than shared through one nozzle, which FlashForge markets as zero purge waste and up to 500% faster multi-colour printing[2][5] |
| Electronics & Power | ||
| Mainboard model & MCU (exact chip markings if teardowns exist) | ELEGOO describes it only as a "Klipper High-Speed Quiet Motherboard" - no board model or MCU published[12] | Not documented |
| Input voltage (110/220 V, switch or auto) | 115/230 V, 50/60 Hz on the product page; ELEGOO's compare page gives 110-120 / 220-240 VAC 50/60 Hz[1][12] | Not documented |
| Total rated power draw | 310 W rated power, 24 V output[12] | Not documented |
| Firmware & Openness | ||
| Firmware base & current version (Klipper fork / Marlin fork / proprietary) | Klipper (ELEGOO names the system "Klipper" outright for the Neptune 4 series, rather than the ELEGOO OS branding used on the Centauri machines)[12][13] | Not named by FlashForge. Supported slicers are Flash Studio, Orca-Flashforge and OrcaSlicer[6] |
| Connectivity, UI & Camera | ||
| Display: size, type, touch? | 4.3-inch colour capacitive touch screen[12] | Not documented |
| On-device UI capabilities (model preview, per-object controls, etc.) | Colour capacitive touch UI; ElegooSlicer recommended, with Orca and Cura also supported[12] | Not documented |
| WiFi (band/standard), Ethernet, USB ports, SD/flash-drive | LAN and USB file transfer; no Wi-Fi is listed for the base Neptune 4, unlike the Plus (USB/LAN/Wi-Fi) and Max (Wi-Fi/USB/WLAN)[1][7][8] | Dual-band Wi-Fi 2.4 GHz + 5 GHz, LAN, USB[5][6] |
| Camera: built-in / optional? Resolution & framerate (verify — marketing often omits real fps) | Not documented | 1080p camera at 30 fps. A camera module is also sold separately at $29.90, so verify whether a given SKU ships with it[5][6][3] |
| Materials Support | ||
| Officially supported filament list | PLA, TPU, PETG, ABS, ASA, Nylon[1] | Not documented |
| Noise & Power Consumption | ||
| Noise: claimed dB and independently measured dB (distance/method) | Operating sound published as 60 dB or less - a manufacturer figure with no distance or method stated, so it is not comparable with an independently measured reading[12] | Not documented |
| Reliability, Support & Ecosystem | ||
| Warranty length & support reputation (evidence, not vibes) | 12 months on brand-new machines and parts, but ELEGOO's own table excludes a long list of parts from that: PEI plate / build plate / nozzle kit / PTFE tube / heater / thermistor / hot end / packaging / manual / tools carry no warranty at all, and the extruder, extruder kit and printhead kit get 6 months. Certified pre-owned machines carry no warranty[14] | Not documented |
Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.
Sources for this comparison
- ELEGOO Neptune 4 product page (Specification table) us.elegoo.com · 2026-08 · vendor
- Flashforge Creator 5 4-Toolheads product page flashforge.com · 2026-08 · vendor
- Flashforge store search results for Creator 5 (live prices) flashforge.com · 2026-08 · vendor
- ELEGOO Neptune 4 Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
- Flashforge Creator 5 and Creator 5 Pro launch report 3dprinting.com · 2026-08 · review
- Flashforge Creator 5 and 5 Pro breakdown antonmansson.com · 2026-08 · review
- ELEGOO Neptune 4 Plus product page (full specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Max product page (Specification table) us.elegoo.com · 2026-08 · vendor
- Flashforge Creator 5 Pro 4-Toolheads product page flashforge.com · 2026-08 · vendor
- ELEGOO US store 3D printers collection (current line-up, Aug 2026) us.elegoo.com · 2026-08 · vendor
- Flashforge printer buyer's guide, 5M to Creator 5 eolasprints.com · 2026-08 · review
- ELEGOO compare-products page, which embeds the full per-model specification JSON for every Neptune, Centauri and OrangeStorm machine us.elegoo.com · 2026-08 · vendor
- ELEGOO Centauri Carbon product page (full specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Refund & Warranty policy (warranty period table) us.elegoo.com · 2026-08 · vendor