3D Printing InfoPrinter comparison
ELEGOO Neptune 4 Plus vs Stratasys F370
Compare hardware, build volume, printing specifications, dated prices and sources.
2 selected · all documented properties
Open these two in the interactive comparisonMore ELEGOO Neptune 4 Plus comparisonsMore Stratasys F370 comparisons
| Property | ELEGOO Neptune 4 PlusBEDSLINGER | Stratasys F370INDUSTRIAL |
|---|---|---|
| Identity | ||
| Brand | ELEGOO | Stratasys |
| Class | BEDSLINGER | INDUSTRIAL |
| Identity & Market | ||
| Manufacturer & exact marketed model name (verify the exact product identity first) | ELEGOO Neptune 4 Plus[1] | Stratasys F370, part of the Stratasys F123 Series[2] |
| Release date (announcement and actual shipping) | Listed on the ELEGOO US store from 20 September 2023 (Shopify publish date), the same date as the Neptune 4 Max[3][4] | The F123 series spec sheet carried is revision 0721a (July 2021). Stratasys does not print a launch date on it[2] |
| Street price (USD; dated snapshot per entry) | $309.00 on us.elegoo.com, Aug 2026, against a compare-at price of $425.00. Only a Ribbon-Cable printhead variant is listed for the Plus, unlike the Neptune 4 and 4 Max which also offer a Type-C version[3][5][4] | Not documented |
| Variants & sibling models — and how to tell them apart (spec-contamination risk) | Middle model of the Neptune 4 family. Against the base Neptune 4: bigger (320 x 320 x 385 mm), but a lower bed ceiling (100 C rather than 110 C) and much lower acceleration (12000 rather than 20000 mm/s2). Against the Max: smaller and lighter (14.4 kg against 18.1 kg) but with a higher bed ceiling (100 C against 85 C) and higher acceleration (12000 against 8000). Its Z drive is 2 lead screws with 2 tie rods, where the Centauri machines use 3 lead screws[1][6][7][8] | Top of the series and the only one with ABS-ESD7, PC-ABS and Diran 410MF07, an Insight software licence, and ProtectAM with US DoD STIG compliance on Red Hat Enterprise Linux. Cabinet and weight are identical to the F170 and F270, so footprint tells you nothing about which model you have[2] |
| Physical & Frame | ||
| Build volume X×Y×Z (mm) — advertised vs actually usable | 320 x 320 x 385 mm; printing platform 330 x 330 mm[1] | 355 x 254 x 355 mm (14 x 10 x 14 in)[2] |
| Machine footprint (mm) & clearance needed (cable/spool overhang) | 533 x 517 x 638 mm; ELEGOO also publishes a maximum size for machine activity of 578 x 750 x 860 mm including rack and tray, so allow 750 mm of depth[1] | 1,626 x 864 x 711 mm (64 x 34 x 28 in)[2] |
| Net weight (kg) | 14.4 kg net, 16.65 kg gross[1] | 124 kg (F120) or 227 kg with consumables (F170, F270, F370)[2] |
| Frame construction & material | CNC-machined aluminium extrusion frame (Neptune 4 family)[6] | Fully enclosed office/classroom-grade cabinet, factory assembled[2] |
| Enclosure: open / enclosed; panel material; door/lid | Open frame, no enclosure[1] | Enclosed build chamber[2] |
| Kinematics & Motion Hardware | ||
| Kinematics (bedslinger i3 / CoreXY / other) | Cartesian i3 bed-slinger[1] | Not documented |
| Z-axis: leadscrew count & type, sync mechanism, anti-backlash | Two lead screws with two tie rods[1] | Not documented |
| Stepper drivers (exact model e.g. TMC2209; UART/SPI; sensorless homing?) | "Silent Drive (All Axes)" is all ELEGOO publishes; the driver part number is not given on the product page[1] | Not documented |
| Speed & Acceleration | ||
| Max print speed (claimed, mm/s) | 30-500 mm/s printing speed, with 250 mm/s given by ELEGOO as the recommended figure - the 500 mm/s number is a ceiling, not a working speed[1] | Not documented |
| Recommended/typical print speed | 250 mm/s recommended printing speed (manufacturer figure)[1] | Not documented |
| Max acceleration (claimed, mm/s²) | 12000 mm/s2 maximum acceleration; default acceleration 5000 mm/s2[1] | Not documented |
| Extruder | ||
| Type (direct drive / bowden) & design name | Dual-gear direct extruder with 2 fans (the Centauri machines use a 1-fan version)[1][8] | Not documented |
| Hotend & Nozzle | ||
| Hotend design (proprietary/standard; quick-swap mechanism?) | Brass nozzle, 0.4 mm, with a titanium-alloy heat break[1] | Not documented |
| Max nozzle temp claimed AND firmware max temp limit (both values) | 300 C claimed max nozzle temperature[1] | Not documented |
| Heated Bed & Surface | ||
| Max bed temp claimed AND firmware limit | 100 C max heated bed temperature at 25 C ambient[1] | Not documented |
| Bed surface (material, texture, coating), single/double-sided | PEI spring steel sheet; ELEGOO notes it is now upgraded to a dual-sided textured PEI + PLA-specific surface[1] | Not documented |
| Leveling & Z-Offset | ||
| Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe) | Manual levelling combined with 121-point auto-levelling[1] | Not documented |
| Filament Handling & Detection | ||
| Filament runout sensor (type, location) | Filament run-out sensor and power-loss recovery; no camera, no clog detection, no auto filament unloading[1] | Not documented |
| Electronics & Power | ||
| Mainboard model & MCU (exact chip markings if teardowns exist) | ELEGOO describes it only as a "Klipper High-Speed Quiet Motherboard" - no board model or MCU is published[1] | Not documented |
| Input voltage (110/220 V, switch or auto) | Not documented | 100-132 V / 15 A or 200-240 V / 7 A, 50/60 Hz[2] |
| Total rated power draw | 320 W rated power; 24 V output; 110-120 V / 220-240 V input[1] | Not documented |
| Firmware & Openness | ||
| Firmware base & current version (Klipper fork / Marlin fork / proprietary) | Klipper (ELEGOO names the system "Klipper" outright for the Neptune 4 Plus, rather than the ELEGOO OS branding used on the Centauri machines)[1][8] | Proprietary Stratasys firmware; print preparation is GrabCAD Print. The F370 additionally carries an Insight software licence and DoD STIG compliance powered by Red Hat Enterprise Linux[2] |
| Connectivity, UI & Camera | ||
| Display: size, type, touch? | 4.3-inch colour capacitive touch screen[1] | Not documented |
| On-device UI capabilities (model preview, per-object controls, etc.) | Colour capacitive touch UI; ElegooSlicer is recommended, with Orca and Cura also supported[1] | Not documented |
| WiFi (band/standard), Ethernet, USB ports, SD/flash-drive | USB, LAN and Wi-Fi[1] | Wired TCP/IP at 100 Mbps minimum, 100base-T Ethernet, RJ45. Wireless-ready IEEE 802.11 n/g/b with WPA2-PSK or 802.1x EAP, CCMP/TKIP encryption[2] |
| Materials Support | ||
| Officially supported filament list | PLA, TPU, PETG, ABS, ASA, Nylon[1] | PLA, ABS-ESD7, ABS-M30, ASA, Diran 410MF072, FDM TPU 92A, PC-ABS, ABS-CF10, with QSR soluble support. Diran and PLA use breakaway rather than soluble support[2] |
| Safety | ||
| Certifications (UL/ETL/CE/FCC — verify, don't assume) | Not documented | CE (low-voltage and EMC directives), FCC, EAC, cTUVus, KC, RoHS, WEEE, REACH, RCM[2] |
| Noise & Power Consumption | ||
| Noise: claimed dB and independently measured dB (distance/method) | Operating sound is published as 65 dB or less - a manufacturer figure with no measuring distance or method given, so it is not comparable with a reviewer's dB reading[1] | 46 dB maximum during build, 35 dB idle — manufacturer specification, no distance or method stated, and not an independent measurement[2] |
| Reliability, Support & Ecosystem | ||
| Warranty length & support reputation (evidence, not vibes) | 12 months on brand-new machines and parts, but ELEGOO's own table excludes a long list of parts from that: PEI plate / build plate / nozzle kit / PTFE tube / heater / thermistor / hot end / packaging / manual / tools carry no warranty at all, and the extruder, extruder kit and printhead kit get 6 months. Certified pre-owned machines carry no warranty[9] | Not documented |
| Independently Measured Performance | ||
| Dimensional accuracy measurements (third-party, with numbers) | Not documented | Parts produced within +/-0.200 mm or +/-0.002 mm/mm, whichever is greater. Manufacturer figure derived from statistical data at 95% dimensional yield; Z accuracy carries an extra -0.000/+slice-height tolerance[2] |
Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.
Sources for this comparison
- ELEGOO Neptune 4 Plus product page (full specification table) us.elegoo.com · 2026-08 · vendor
- Stratasys F123 Series product specification sheet (PSS_FDM_F123Series_0721a, PDF) stratasys.com · 2026-08 · doc
- ELEGOO Neptune 4 Plus Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Max Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 product page (Specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Max product page (Specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Centauri Carbon product page (full specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Refund & Warranty policy (warranty period table) us.elegoo.com · 2026-08 · vendor