3D Printing InfoPrinter comparison
ELEGOO Neptune 4 Plus vs Snapmaker Artisan
Compare hardware, build volume, printing specifications, dated prices and sources.
2 selected · all documented properties
Open these two in the interactive comparisonMore ELEGOO Neptune 4 Plus comparisonsMore Snapmaker Artisan comparisons
| Property | ELEGOO Neptune 4 PlusBEDSLINGER | Snapmaker ArtisanIDEX |
|---|---|---|
| Identity | ||
| Brand | ELEGOO | Snapmaker |
| Class | BEDSLINGER | IDEX |
| Identity & Market | ||
| Manufacturer & exact marketed model name (verify the exact product identity first) | ELEGOO Neptune 4 Plus[1] | Snapmaker Artisan 3-in-1 (3D printing, laser, CNC)[2] |
| Release date (announcement and actual shipping) | Listed on the ELEGOO US store from 20 September 2023 (Shopify publish date), the same date as the Neptune 4 Max[3][4] | Not documented |
| Street price (USD; dated snapshot per entry) | $309.00 on us.elegoo.com, Aug 2026, against a compare-at price of $425.00. Only a Ribbon-Cable printhead variant is listed for the Plus, unlike the Neptune 4 and 4 Max which also offer a Type-C version[3][5][4] | $2,996.00 against a $5,046.00 compare-at price on us.snapmaker.com, but marked Unavailable, checked Aug 2026[2] |
| Variants & sibling models — and how to tell them apart (spec-contamination risk) | Middle model of the Neptune 4 family. Against the base Neptune 4: bigger (320 x 320 x 385 mm), but a lower bed ceiling (100 C rather than 110 C) and much lower acceleration (12000 rather than 20000 mm/s2). Against the Max: smaller and lighter (14.4 kg against 18.1 kg) but with a higher bed ceiling (100 C against 85 C) and higher acceleration (12000 against 8000). Its Z drive is 2 lead screws with 2 tie rods, where the Centauri machines use 3 lead screws[1][6][7][8] | The 3D-printing work area depends on which nozzle is used: 350 x 400 x 400 mm in dual-nozzle mode, 375 x 400 x 400 with the left nozzle only, 400 x 400 x 400 with the right nozzle only. The bed is also zoned: a 260 x 260 mm inner zone reaches 110 °C while the outer zone stops at 80 °C. A quoted "400x400x400 / 110 °C" therefore describes no single real configuration. Laser module is 10 W or 40 W[2] |
| Physical & Frame | ||
| Build volume X×Y×Z (mm) — advertised vs actually usable | 320 x 320 x 385 mm; printing platform 330 x 330 mm[1] | 350 x 400 x 400 mm in dual-nozzle mode (400 x 400 x 400 with the right nozzle alone)[2] |
| Machine footprint (mm) & clearance needed (cable/spool overhang) | 533 x 517 x 638 mm; ELEGOO also publishes a maximum size for machine activity of 578 x 750 x 860 mm including rack and tray, so allow 750 mm of depth[1] | 580 x 620 x 634 mm bare; 665 x 943 x 705 mm with the enclosure[2] |
| Net weight (kg) | 14.4 kg net, 16.65 kg gross[1] | Snapmaker publishes package weights rather than a net weight: 37.3 kg (package A) plus 25.2 kg (package B); the premium bundle splits as 37.3 + 19.5 + 1.91 kg[2] |
| Frame construction & material | CNC-machined aluminium extrusion frame (Neptune 4 family)[6] | Not documented |
| Enclosure: open / enclosed; panel material; door/lid | Open frame, no enclosure[1] | Enclosure available; the enclosed footprint is quoted separately at 665 x 943 x 705 mm[2] |
| Kinematics & Motion Hardware | ||
| Kinematics (bedslinger i3 / CoreXY / other) | Cartesian i3 bed-slinger[1] | IDEX — two independently driven print heads[2] |
| Z-axis: leadscrew count & type, sync mechanism, anti-backlash | Two lead screws with two tie rods[1] | Z-axis lead 8 mm; X and Y leads 40 mm[2] |
| Stepper drivers (exact model e.g. TMC2209; UART/SPI; sensorless homing?) | "Silent Drive (All Axes)" is all ELEGOO publishes; the driver part number is not given on the product page[1] | TMC2209[2] |
| Speed & Acceleration | ||
| Max print speed (claimed, mm/s) | 30-500 mm/s printing speed, with 250 mm/s given by ELEGOO as the recommended figure - the 500 mm/s number is a ceiling, not a working speed[1] | 180 mm/s maximum recommended print speed (manufacturer figure — a recommendation, not a peak claim)[2] |
| Recommended/typical print speed | 250 mm/s recommended printing speed (manufacturer figure)[1] | Not documented |
| Max acceleration (claimed, mm/s²) | 12000 mm/s2 maximum acceleration; default acceleration 5000 mm/s2[1] | Not documented |
| Extruder | ||
| Type (direct drive / bowden) & design name | Dual-gear direct extruder with 2 fans (the Centauri machines use a 1-fan version)[1][8] | Not documented |
| Hotend & Nozzle | ||
| Hotend design (proprietary/standard; quick-swap mechanism?) | Brass nozzle, 0.4 mm, with a titanium-alloy heat break[1] | Not documented |
| Max nozzle temp claimed AND firmware max temp limit (both values) | 300 C claimed max nozzle temperature[1] | 300 °C maximum (manufacturer claim)[2] |
| Stock nozzle size & sizes included in box | Not documented | 0.4 mm standard; 0.2, 0.6 and 0.8 mm optional[2] |
| Stock nozzle material (brass / hardened steel / plated copper / composite tip) | Not documented | Brass standard, hardened steel optional[2] |
| Heated Bed & Surface | ||
| Max bed temp claimed AND firmware limit | 100 C max heated bed temperature at 25 C ambient[1] | 110 °C in the 260 x 260 mm inner zone; 80 °C in the outer zone[2] |
| Bed surface (material, texture, coating), single/double-sided | PEI spring steel sheet; ELEGOO notes it is now upgraded to a dual-sided textured PEI + PLA-specific surface[1] | Dual-sided textured PEI sheet[2] |
| Leveling & Z-Offset | ||
| Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe) | Manual levelling combined with 121-point auto-levelling[1] | Not documented |
| Filament Handling & Detection | ||
| Filament runout sensor (type, location) | Filament run-out sensor and power-loss recovery; no camera, no clog detection, no auto filament unloading[1] | Not documented |
| Electronics & Power | ||
| Mainboard model & MCU (exact chip markings if teardowns exist) | ELEGOO describes it only as a "Klipper High-Speed Quiet Motherboard" - no board model or MCU is published[1] | Not documented |
| Total rated power draw | 320 W rated power; 24 V output; 110-120 V / 220-240 V input[1] | Integrated controller rated 300 W + 450 W[2] |
| Firmware & Openness | ||
| Firmware base & current version (Klipper fork / Marlin fork / proprietary) | Klipper (ELEGOO names the system "Klipper" outright for the Neptune 4 Plus, rather than the ELEGOO OS branding used on the Centauri machines)[1][8] | Not named by Snapmaker; the controller runs Android and the supplied software is Snapmaker Luban, with third-party software supported[2] |
| Connectivity, UI & Camera | ||
| Display: size, type, touch? | 4.3-inch colour capacitive touch screen[1] | 7-inch touchscreen[2] |
| On-device UI capabilities (model preview, per-object controls, etc.) | Colour capacitive touch UI; ElegooSlicer is recommended, with Orca and Cura also supported[1] | Not documented |
| WiFi (band/standard), Ethernet, USB ports, SD/flash-drive | USB, LAN and Wi-Fi[1] | Wi-Fi, USB cable, USB flash drive[2] |
| Materials Support | ||
| Officially supported filament list | PLA, TPU, PETG, ABS, ASA, Nylon[1] | PLA, ABS, ASA, PETG, TPU (>=90 Shore A), breakaway support, PVA, HIPS, nylon, and carbon/glass-fibre reinforced variants[2] |
| Noise & Power Consumption | ||
| Noise: claimed dB and independently measured dB (distance/method) | Operating sound is published as 65 dB or less - a manufacturer figure with no measuring distance or method given, so it is not comparable with a reviewer's dB reading[1] | Not documented |
| Reliability, Support & Ecosystem | ||
| Warranty length & support reputation (evidence, not vibes) | 12 months on brand-new machines and parts, but ELEGOO's own table excludes a long list of parts from that: PEI plate / build plate / nozzle kit / PTFE tube / heater / thermistor / hot end / packaging / manual / tools carry no warranty at all, and the extruder, extruder kit and printhead kit get 6 months. Certified pre-owned machines carry no warranty[9] | Not documented |
| Independently Measured Performance | ||
| Dimensional accuracy measurements (third-party, with numbers) | Not documented | Repeatability +/-0.05 mm (manufacturer specification, not an independent measurement)[2] |
Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.
Sources for this comparison
- ELEGOO Neptune 4 Plus product page (full specification table) us.elegoo.com · 2026-08 · vendor
- Snapmaker Artisan 3-in-1 product page us.snapmaker.com · 2026-08 · vendor
- ELEGOO Neptune 4 Plus Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Max Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 product page (Specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Max product page (Specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Centauri Carbon product page (full specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Refund & Warranty policy (warranty period table) us.elegoo.com · 2026-08 · vendor