3D Printing InfoPrinter comparison
ELEGOO Neptune 4 Plus vs Raise3D Pro3
Compare hardware, build volume, printing specifications, dated prices and sources.
2 selected · all documented properties
Open these two in the interactive comparisonMore ELEGOO Neptune 4 Plus comparisonsMore Raise3D Pro3 comparisons
| Property | ELEGOO Neptune 4 PlusBEDSLINGER | Raise3D Pro3IDEX |
|---|---|---|
| Identity | ||
| Brand | ELEGOO | Raise3D |
| Class | BEDSLINGER | IDEX |
| Identity & Market | ||
| Manufacturer & exact marketed model name (verify the exact product identity first) | ELEGOO Neptune 4 Plus[1] | Raise3D Pro3 3D Printer[2][3] |
| Release date (announcement and actual shipping) | Listed on the ELEGOO US store from 20 September 2023 (Shopify publish date), the same date as the Neptune 4 Max[4][5] | Not documented |
| Street price (USD; dated snapshot per entry) | $309.00 on us.elegoo.com, Aug 2026, against a compare-at price of $425.00. Only a Ribbon-Cable printhead variant is listed for the Plus, unlike the Neptune 4 and 4 Max which also offer a Type-C version[4][6][5] | $2,999.00 on Raise3D's own store, available, checked Aug 2026[3] |
| Variants & sibling models — and how to tell them apart (spec-contamination risk) | Middle model of the Neptune 4 family. Against the base Neptune 4: bigger (320 x 320 x 385 mm), but a lower bed ceiling (100 C rather than 110 C) and much lower acceleration (12000 rather than 20000 mm/s2). Against the Max: smaller and lighter (14.4 kg against 18.1 kg) but with a higher bed ceiling (100 C against 85 C) and higher acceleration (12000 against 8000). Its Z drive is 2 lead screws with 2 tie rods, where the Centauri machines use 3 lead screws[1][7][8][9] | A crowded family with materially different prices: Pro3 $2,999, Pro3 Hyper Speed Package $4,999, Pro3 HS $4,599, Pro3 Plus HS $6,099. Build volume also changes with head count: 300 x 300 x 300 mm single-head, 255 x 300 x 300 mm dual-head. Raise3D's smaller E-series (E2 $1,999, E2CF $2,499, E3 $2,499) and the resin DF2 line are separate machines entirely[3][10][2] |
| Physical & Frame | ||
| Build volume X×Y×Z (mm) — advertised vs actually usable | 320 x 320 x 385 mm; printing platform 330 x 330 mm[1] | 300 x 300 x 300 mm with one extruder; 255 x 300 x 300 mm with both[2] |
| Machine footprint (mm) & clearance needed (cable/spool overhang) | 533 x 517 x 638 mm; ELEGOO also publishes a maximum size for machine activity of 578 x 750 x 860 mm including rack and tray, so allow 750 mm of depth[1] | 620 x 626 x 760 mm[2] |
| Net weight (kg) | 14.4 kg net, 16.65 kg gross[1] | 52.5 kg net[2] |
| Frame construction & material | CNC-machined aluminium extrusion frame (Neptune 4 family)[7] | Fully assembled enclosed professional chassis[2] |
| Enclosure: open / enclosed; panel material; door/lid | Open frame, no enclosure[1] | Enclosed with a HEPA and activated-charcoal filter[2] |
| Kinematics & Motion Hardware | ||
| Kinematics (bedslinger i3 / CoreXY / other) | Cartesian i3 bed-slinger[1] | Dual-head with an electronic lifting system[2] |
| Z-axis: leadscrew count & type, sync mechanism, anti-backlash | Two lead screws with two tie rods[1] | Not documented |
| Stepper drivers (exact model e.g. TMC2209; UART/SPI; sensorless homing?) | "Silent Drive (All Axes)" is all ELEGOO publishes; the driver part number is not given on the product page[1] | Not documented |
| Speed & Acceleration | ||
| Max print speed (claimed, mm/s) | 30-500 mm/s printing speed, with 250 mm/s given by ELEGOO as the recommended figure - the 500 mm/s number is a ceiling, not a working speed[1] | Not documented |
| Recommended/typical print speed | 250 mm/s recommended printing speed (manufacturer figure)[1] | Not documented |
| Max travel speed | Not documented | Print-head travel speed 30-150 mm/s (manufacturer figure)[2] |
| Max acceleration (claimed, mm/s²) | 12000 mm/s2 maximum acceleration; default acceleration 5000 mm/s2[1] | Not documented |
| Extruder | ||
| Type (direct drive / bowden) & design name | Dual-gear direct extruder with 2 fans (the Centauri machines use a 1-fan version)[1][9] | Dual print heads, 1.75 mm filament[2] |
| Hotend & Nozzle | ||
| Hotend design (proprietary/standard; quick-swap mechanism?) | Brass nozzle, 0.4 mm, with a titanium-alloy heat break[1] | Not documented |
| Max nozzle temp claimed AND firmware max temp limit (both values) | 300 C claimed max nozzle temperature[1] | 300 °C maximum nozzle temperature[2] |
| Stock nozzle size & sizes included in box | Not documented | 0.4 mm default; 0.2, 0.6, 0.8 and 1.0 mm available[2] |
| Heated Bed & Surface | ||
| Max bed temp claimed AND firmware limit | 100 C max heated bed temperature at 25 C ambient[1] | 120 °C maximum build-plate temperature, silicone heater[2] |
| Bed surface (material, texture, coating), single/double-sided | PEI spring steel sheet; ELEGOO notes it is now upgraded to a dual-sided textured PEI + PLA-specific surface[1] | Flexible steel plate with BuildTak[2] |
| Leveling & Z-Offset | ||
| Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe) | Manual levelling combined with 121-point auto-levelling[1] | Mesh levelling with flatness detection[2] |
| Filament Handling & Detection | ||
| Filament runout sensor (type, location) | Filament run-out sensor and power-loss recovery; no camera, no clog detection, no auto filament unloading[1] | Not documented |
| Cooling & Air Handling | ||
| Chamber/exhaust fan & filtration (activated carbon / HEPA) | Not documented | HEPA filter with activated charcoal[2] |
| Electronics & Power | ||
| Mainboard model & MCU (exact chip markings if teardowns exist) | ELEGOO describes it only as a "Klipper High-Speed Quiet Motherboard" - no board model or MCU is published[1] | Motion controller Atmel ARM Cortex-M4 at 120 MHz with FPU; logic controller NXP ARM Cortex-A9 quad-core at 1 GHz[2] |
| Host computer (SoC, RAM, storage) if firmware runs on embedded Linux | Not documented | 1 GB RAM, 8 GB onboard flash, embedded Linux[2] |
| Input voltage (110/220 V, switch or auto) | Not documented | 100-240 V AC, 50/60 Hz input; 24 V DC, 600 W output[2] |
| Total rated power draw | 320 W rated power; 24 V output; 110-120 V / 220-240 V input[1] | 600 W output[2] |
| Firmware & Openness | ||
| Firmware base & current version (Klipper fork / Marlin fork / proprietary) | Klipper (ELEGOO names the system "Klipper" outright for the Neptune 4 Plus, rather than the ELEGOO OS branding used on the Centauri machines)[1][9] | Embedded Linux on the logic controller; slicing is ideaMaker. Firmware base not published[2] |
| Connectivity, UI & Camera | ||
| Display: size, type, touch? | 4.3-inch colour capacitive touch screen[1] | 7-inch touchscreen, 1024 x 600[2] |
| On-device UI capabilities (model preview, per-object controls, etc.) | Colour capacitive touch UI; ElegooSlicer is recommended, with Orca and Cura also supported[1] | Not documented |
| WiFi (band/standard), Ethernet, USB ports, SD/flash-drive | USB, LAN and Wi-Fi[1] | Wi-Fi, Ethernet, USB 2.0 x2; live camera[2] |
| Camera: built-in / optional? Resolution & framerate (verify — marketing often omits real fps) | Not documented | Live camera fitted; resolution not published[2] |
| Materials Support | ||
| Officially supported filament list | PLA, TPU, PETG, ABS, ASA, Nylon[1] | PLA, ABS, HIPS, PC, TPU, TPE, PETG, ASA, PP, PVA, nylon, composites and metal/wood-filled grades[2] |
| Noise & Power Consumption | ||
| Noise: claimed dB and independently measured dB (distance/method) | Operating sound is published as 65 dB or less - a manufacturer figure with no measuring distance or method given, so it is not comparable with a reviewer's dB reading[1] | Under 55 dB(A) while printing, manufacturer figure. No independent measurement; distance and method not stated[2] |
| Reliability, Support & Ecosystem | ||
| Warranty length & support reputation (evidence, not vibes) | 12 months on brand-new machines and parts, but ELEGOO's own table excludes a long list of parts from that: PEI plate / build plate / nozzle kit / PTFE tube / heater / thermistor / hot end / packaging / manual / tools carry no warranty at all, and the extruder, extruder kit and printhead kit get 6 months. Certified pre-owned machines carry no warranty[11] | Not documented |
| Independently Measured Performance | ||
| Dimensional accuracy measurements (third-party, with numbers) | Not documented | XYZ step size 0.78125 / 0.78125 / 0.078125 micron (manufacturer specification, not an accuracy measurement)[2] |
Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.
Sources for this comparison
- ELEGOO Neptune 4 Plus product page (full specification table) us.elegoo.com · 2026-08 · vendor
- Raise3D Pro3 3D Printer listing matterhackers.com · 2026-08 · vendor
- Raise3D 3D-printer collection product feed (live prices) shop.raise3d.com · 2026-08 · vendor
- ELEGOO Neptune 4 Plus Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Max Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 product page (Specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Max product page (Specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Centauri Carbon product page (full specification table) us.elegoo.com · 2026-08 · vendor
- Raise3D E2 3D Printer product page shop.raise3d.com · 2026-08 · vendor
- ELEGOO Refund & Warranty policy (warranty period table) us.elegoo.com · 2026-08 · vendor