3D Printing InfoPrinter comparison
ELEGOO Neptune 4 Plus vs Prusa CORE One+ (Gen 2)
Compare hardware, build volume, printing specifications, dated prices and sources.
2 selected · all documented properties
Open these two in the interactive comparisonMore ELEGOO Neptune 4 Plus comparisonsMore Prusa CORE One+ (Gen 2) comparisons
| Property | ELEGOO Neptune 4 PlusBEDSLINGER | Prusa CORE One+ (Gen 2)COREXY |
|---|---|---|
| Identity | ||
| Brand | ELEGOO | Prusa Research |
| Class | BEDSLINGER | COREXY |
| Identity & Market | ||
| Manufacturer & exact marketed model name (verify the exact product identity first) | ELEGOO Neptune 4 Plus[1] | Prusa CORE One+ (Gen 2). Prusa's e-shop lists "Prusa CORE One+ (Gen 2)" and "Prusa CORE One+ (Gen 2) Assembly kit"[2][3] |
| Release date (announcement and actual shipping) | Listed on the ELEGOO US store from 20 September 2023 (Shopify publish date), the same date as the Neptune 4 Max[4][5] | The CORE One+ (Gen 2) refresh was announced on 13 August 2026, on sale immediately, with the first assembled units shipping at once and kits, upgrade kits and individual parts rolling out over the following weeks. It succeeds the CORE One and CORE One+ on the same platform[6] |
| Street price (USD; dated snapshot per entry) | $309.00 on us.elegoo.com, Aug 2026, against a compare-at price of $425.00. Only a Ribbon-Cable printhead variant is listed for the Plus, unlike the Neptune 4 and 4 Max which also offer a Type-C version[4][7][5] | $1,202.78 assembled, $925.00 as an assembly kit, on prusa3d.com, Aug 2026. Bundles run to $1,301.85 with camera and advanced filtration. Prusa's own marketing table on the same page quotes "from $1,299" assembled, which does not match the live e-shop price[3][2] |
| Variants & sibling models — and how to tell them apart (spec-contamination risk) | Middle model of the Neptune 4 family. Against the base Neptune 4: bigger (320 x 320 x 385 mm), but a lower bed ceiling (100 C rather than 110 C) and much lower acceleration (12000 rather than 20000 mm/s2). Against the Max: smaller and lighter (14.4 kg against 18.1 kg) but with a higher bed ceiling (100 C against 85 C) and higher acceleration (12000 against 8000). Its Z drive is 2 lead screws with 2 tie rods, where the Centauri machines use 3 lead screws[1][8][9][10] | Three generations share the CORE One name: the original CORE One, the CORE One+, and the CORE One+ (Gen 2), with paid upgrade kits between them (CORE One+ to CORE One+ (Gen 2), and an MK4S to CORE One+ (Gen 2) conversion kit). The specifications recorded here are those published on Prusa's current CORE One+ (Gen 2) page and should not be assumed to hold for a first-generation CORE One. The INDX 4-tool and 8-tool machines are variants of the same product page, and the CORE One L is a larger, separate machine[2][3][11] |
| Market position: superseded? successor announced? | Not documented | Current model and Prusa's mainstream enclosed machine, above the MK4S and below the CORE One L+[3] |
| Physical & Frame | ||
| Build volume X×Y×Z (mm) — advertised vs actually usable | 320 x 320 x 385 mm; printing platform 330 x 330 mm[1] | 250 x 220 x 270 mm (manufacturer figure)[2] |
| Machine footprint (mm) & clearance needed (cable/spool overhang) | 533 x 517 x 638 mm; ELEGOO also publishes a maximum size for machine activity of 578 x 750 x 860 mm including rack and tray, so allow 750 mm of depth[1] | 415 x 444 x 555 mm (X x Y x Z)[2] |
| Net weight (kg) | 14.4 kg net, 16.65 kg gross[1] | 22.5 kg[2] |
| Frame construction & material | CNC-machined aluminium extrusion frame (Neptune 4 family)[8] | All-steel exoskeleton (Prusa's own comparison wording, against "aluminium extrusions and frame" for the MK4S)[12] |
| Enclosure: open / enclosed; panel material; door/lid | Open frame, no enclosure[1] | Fully enclosed with a door-open sensor and active chamber temperature control up to 55 C; HEPA/advanced filtration is an optional add-on[2][12] |
| Passive chamber temperature reached (if enclosed; measured values preferred) | Not documented | Active chamber heating, maximum 55 C (manufacturer figure)[2] |
| Kinematics & Motion Hardware | ||
| Kinematics (bedslinger i3 / CoreXY / other) | Cartesian i3 bed-slinger[1] | CoreXY - stated as such in Prusa's own comparison table against the Cartesian MK4S[2] |
| Z-axis: leadscrew count & type, sync mechanism, anti-backlash | Two lead screws with two tie rods[1] | Not documented |
| Stepper motors (frame size, step angle, brand if known) | Not documented | 0.9 degree X and Y stepper motors[2] |
| Stepper drivers (exact model e.g. TMC2209; UART/SPI; sensorless homing?) | "Silent Drive (All Axes)" is all ELEGOO publishes; the driver part number is not given on the product page[1] | Trinamic 2130[2] |
| Speed & Acceleration | ||
| Max print speed (claimed, mm/s) | 30-500 mm/s printing speed, with 250 mm/s given by ELEGOO as the recommended figure - the 500 mm/s number is a ceiling, not a working speed[1] | Not documented |
| Recommended/typical print speed | 250 mm/s recommended printing speed (manufacturer figure)[1] | Not documented |
| Max acceleration (claimed, mm/s²) | 12000 mm/s2 maximum acceleration; default acceleration 5000 mm/s2[1] | Not documented |
| Extruder | ||
| Type (direct drive / bowden) & design name | Dual-gear direct extruder with 2 fans (the Centauri machines use a 1-fan version)[1][10] | Nextruder direct drive, E3D V6 compatible with an adapter; planetary gear system with a 10:1 ratio; aluminium heatsink and all-metal hotend[2] |
| Gear ratio & drive gear material | Not documented | 10:1 planetary gearbox[2] |
| Hotend & Nozzle | ||
| Hotend design (proprietary/standard; quick-swap mechanism?) | Brass nozzle, 0.4 mm, with a titanium-alloy heat break[1] | Quick-swap nozzle system; high-flow Prusa brass CHT 0.4 mm nozzle supplied. An optional HT hotend raises the ceiling to 400 C[2] |
| Max nozzle temp claimed AND firmware max temp limit (both values) | 300 C claimed max nozzle temperature[1] | 290 C claimed max nozzle temperature. Prusa's comparison table adds "400 C w/ HT" for the optional HT hotend, which its 13 August 2026 blog post says will only become available in September 2026 - so 400 C is a forthcoming option, not a shipping specification[2][6] |
| Heated Bed & Surface | ||
| Max bed temp claimed AND firmware limit | 100 C max heated bed temperature at 25 C ambient[1] | 120 C max heatbed temperature[2] |
| Bed surface (material, texture, coating), single/double-sided | PEI spring steel sheet; ELEGOO notes it is now upgraded to a dual-sided textured PEI + PLA-specific surface[1] | Magnetic heatbed with removable PEI spring-steel sheets; whole-bed heating regardless of object size[2] |
| Leveling & Z-Offset | ||
| Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe) | Manual levelling combined with 121-point auto-levelling[1] | Load-cell sensor - fully automatic first-layer calibration with the nozzle as the probe[2] |
| Filament Handling & Detection | ||
| Filament runout sensor (type, location) | Filament run-out sensor and power-loss recovery; no camera, no clog detection, no auto filament unloading[1] | Two filament sensors, plus a door sensor and five Semitec thermistors with fan RPM monitoring[2][12] |
| Multi-material/multi-color capability or official upgrade path | Not documented | MMU3 for five filaments, or the INDX system for up to eight, both officially supported[2] |
| Cooling & Air Handling | ||
| Part-cooling fan(s): count, size, ducting design | Not documented | High-performance turbine part-cooling fan with 360-degree cooling, the same arrangement as the MK4S[2] |
| Electronics & Power | ||
| Mainboard model & MCU (exact chip markings if teardowns exist) | ELEGOO describes it only as a "Klipper High-Speed Quiet Motherboard" - no board model or MCU is published[1] | Custom 32-bit xBuddy board with STM32[2] |
| PSU (brand, wattage, rail voltage) | Not documented | 240 W PSU with hardware power panic[2] |
| Total rated power draw | 320 W rated power; 24 V output; 110-120 V / 220-240 V input[1] | Power consumption 90 W printing PLA, 110 W printing ABS (manufacturer figures)[2] |
| Firmware & Openness | ||
| Firmware base & current version (Klipper fork / Marlin fork / proprietary) | Klipper (ELEGOO names the system "Klipper" outright for the Neptune 4 Plus, rather than the ELEGOO OS branding used on the Centauri machines)[1][10] | Open-source Prusa Buddy firmware. The source tree (prusa3d/Prusa-Firmware-Buddy on GitHub) explicitly covers the Original Prusa MINI/MINI+, MK4, XL and CORE One and was last pushed to in August 2026. Updates are applied from a USB drive, through Prusa Connect or through the Prusa mobile app[13][12] |
| Connectivity, UI & Camera | ||
| Display: size, type, touch? | 4.3-inch colour capacitive touch screen[1] | 3.5-inch 65k-colour graphic screen with touch control[2] |
| On-device UI capabilities (model preview, per-object controls, etc.) | Colour capacitive touch UI; ElegooSlicer is recommended, with Orca and Cura also supported[1] | On-device touch UI; remote monitoring and printing through Prusa Connect and the Prusa mobile app; firmware updates from USB, Prusa Connect or the app[2] |
| WiFi (band/standard), Ethernet, USB ports, SD/flash-drive | USB, LAN and Wi-Fi[1] | Ethernet and Wi-Fi (NFC receiver plus an optional Wi-Fi module), USB drive for print files[2] |
| Camera: built-in / optional? Resolution & framerate (verify — marketing often omits real fps) | Not documented | Optional in-chamber camera solution (Buddy3D camera bundle listed at $1,237.03 against $1,202.78 for the bare printer)[2][3] |
| Materials Support | ||
| Officially supported filament list | PLA, TPU, PETG, ABS, ASA, Nylon[1] | PLA, PETG, Flex, PVA, PC, PP, CPE, PVB, and - as advanced materials in the heated chamber - ABS, ASA, HIPS and PA[2] |
| Safety | ||
| Thermal runaway protection (verify in firmware source if at all possible) | Not documented | The xBuddy platform carries hardware overcurrent protection that cuts heater and heatbed power above 15 A, and the firmware is open-source and auditable[14][13] |
| Noise & Power Consumption | ||
| Noise: claimed dB and independently measured dB (distance/method) | Operating sound is published as 65 dB or less - a manufacturer figure with no measuring distance or method given, so it is not comparable with a reviewer's dB reading[1] | Not documented |
| Reliability, Support & Ecosystem | ||
| Warranty length & support reputation (evidence, not vibes) | 12 months on brand-new machines and parts, but ELEGOO's own table excludes a long list of parts from that: PEI plate / build plate / nozzle kit / PTFE tube / heater / thermistor / hot end / packaging / manual / tools carry no warranty at all, and the extruder, extruder kit and printhead kit get 6 months. Certified pre-owned machines carry no warranty[15] | 2-year warranty for consumers in the EU, Liechtenstein, Switzerland, Norway and Iceland; 1 year for EU enterprises and 1 year for the rest of the world, which includes the United States. A printer bought from a reseller or privately carries 1 year from the original delivery date and is handled by the reseller. Prusa advertises 24/7 chat and e-mail support in seven languages[16][12] |
Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.
Sources for this comparison
- ELEGOO Neptune 4 Plus product page (full specification table) us.elegoo.com · 2026-08 · vendor
- Prusa CORE One+ (Gen 2) product page (Technical Parameters + CORE One+/MK4S/CORE One L comparison) prusa3d.com · 2026-08 · vendor
- Prusa 3D printers category listing with live e-shop prices, Aug 2026 prusa3d.com · 2026-08 · vendor
- ELEGOO Neptune 4 Plus Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Max Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
- Prusa blog - Better Prints, Easier Use: Prusa XL+, CORE One L+ and CORE One+ (Gen 2), Our Big Product Update (published 13 August 2026) blog.prusa3d.com · 2026-08 · doc
- ELEGOO Neptune 4 Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 product page (Specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Max product page (Specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Centauri Carbon product page (full specification table) us.elegoo.com · 2026-08 · vendor
- Prusa CORE One L+ product page (CORE One L+ Technical Specifications) prusa3d.com · 2026-08 · vendor
- Original Prusa MK4S 3D Printer product page (Technical Parameters + CORE One+/MK4S/XL comparison table) prusa3d.com · 2026-08 · vendor
- GitHub - prusa3d/Prusa-Firmware-Buddy (firmware for MINI, MK4, XL and CORE One) github.com · 2026-08 · doc
- Prusa blog - Original Prusa MK4 is here (published 29 March 2023), including the MK4 specification table and launch prices blog.prusa3d.com · 2026-08 · doc
- ELEGOO Refund & Warranty policy (warranty period table) us.elegoo.com · 2026-08 · vendor
- Prusa Knowledge Base - Warranty help.prusa3d.com · 2026-08 · doc