3D Printing InfoPrinter comparison
ELEGOO Neptune 4 Plus vs Prusa CORE One L+
Compare hardware, build volume, printing specifications, dated prices and sources.
2 selected · all documented properties
Open these two in the interactive comparisonMore ELEGOO Neptune 4 Plus comparisonsMore Prusa CORE One L+ comparisons
| Property | ELEGOO Neptune 4 PlusBEDSLINGER | Prusa CORE One L+COREXY |
|---|---|---|
| Identity | ||
| Brand | ELEGOO | Prusa Research |
| Class | BEDSLINGER | COREXY |
| Identity & Market | ||
| Manufacturer & exact marketed model name (verify the exact product identity first) | ELEGOO Neptune 4 Plus[1] | Prusa CORE One L+[2] |
| Release date (announcement and actual shipping) | Listed on the ELEGOO US store from 20 September 2023 (Shopify publish date), the same date as the Neptune 4 Max[3][4] | The CORE One L+ refresh was announced on 13 August 2026 and went on sale immediately, with the first assembled units shipping at once; it adds GT1.5 belts and an integrated nozzle wiper to the CORE One L[5] |
| Street price (USD; dated snapshot per entry) | $309.00 on us.elegoo.com, Aug 2026, against a compare-at price of $425.00. Only a Ribbon-Cable printhead variant is listed for the Plus, unlike the Neptune 4 and 4 Max which also offer a Type-C version[3][6][4] | $1,850.93 on prusa3d.com, Aug 2026; $1,925.00 with the Advanced Filtration bundle. Prusa's own comparison text on the CORE One+ page quotes "from $1,799", which does not match the live e-shop price[7][8] |
| Variants & sibling models — and how to tell them apart (spec-contamination risk) | Middle model of the Neptune 4 family. Against the base Neptune 4: bigger (320 x 320 x 385 mm), but a lower bed ceiling (100 C rather than 110 C) and much lower acceleration (12000 rather than 20000 mm/s2). Against the Max: smaller and lighter (14.4 kg against 18.1 kg) but with a higher bed ceiling (100 C against 85 C) and higher acceleration (12000 against 8000). Its Z drive is 2 lead screws with 2 tie rods, where the Centauri machines use 3 lead screws[1][9][10][11] | Larger sibling of the CORE One+ (Gen 2): 300 x 300 x 330 mm against 250 x 220 x 270 mm, 60 C chamber against 55 C, 21.9 kg against 22.5 kg (the L is the lighter of the two despite being larger). A CORE One L to CORE One L+ upgrade kit exists, so "CORE One L" and "CORE One L+" are different revisions. A Critical Infrastructure Edition is also listed[2][8][7] |
| Physical & Frame | ||
| Build volume X×Y×Z (mm) — advertised vs actually usable | 320 x 320 x 385 mm; printing platform 330 x 330 mm[1] | 300 x 300 x 330 mm, which Prusa states as 29.7 litres[2] |
| Machine footprint (mm) & clearance needed (cable/spool overhang) | 533 x 517 x 638 mm; ELEGOO also publishes a maximum size for machine activity of 578 x 750 x 860 mm including rack and tray, so allow 750 mm of depth[1] | 469 x 521 x 635 mm[2] |
| Net weight (kg) | 14.4 kg net, 16.65 kg gross[1] | 21.9 kg (48.3 lb)[2] |
| Frame construction & material | CNC-machined aluminium extrusion frame (Neptune 4 family)[9] | Not documented |
| Enclosure: open / enclosed; panel material; door/lid | Open frame, no enclosure[1] | Fully enclosed with a chamber door-open sensor and an active convection heated chamber up to 60 C; advanced filtration is an optional add-on[2] |
| Passive chamber temperature reached (if enclosed; measured values preferred) | Not documented | Active convection chamber heating, maximum 60 C (manufacturer figure)[2] |
| Kinematics & Motion Hardware | ||
| Kinematics (bedslinger i3 / CoreXY / other) | Cartesian i3 bed-slinger[1] | CoreXY - stated in Prusa's CORE One+ comparison table[8] |
| Z-axis: leadscrew count & type, sync mechanism, anti-backlash | Two lead screws with two tie rods[1] | Not documented |
| Stepper drivers (exact model e.g. TMC2209; UART/SPI; sensorless homing?) | "Silent Drive (All Axes)" is all ELEGOO publishes; the driver part number is not given on the product page[1] | Trinamic drivers on the custom xBuddy mainboard (Prusa's CORE One L+ specification says "custom 32-bit xBuddy mainboard with STM32 processor & Trinamic drivers"; it does not give the driver part number)[2] |
| Speed & Acceleration | ||
| Max print speed (claimed, mm/s) | 30-500 mm/s printing speed, with 250 mm/s given by ELEGOO as the recommended figure - the 500 mm/s number is a ceiling, not a working speed[1] | Not documented |
| Recommended/typical print speed | 250 mm/s recommended printing speed (manufacturer figure)[1] | Not documented |
| Max acceleration (claimed, mm/s²) | 12000 mm/s2 maximum acceleration; default acceleration 5000 mm/s2[1] | Not documented |
| Vibration Compensation / Input Shaping | ||
| Input shaping supported? Implementation (Klipper IS / Marlin ZV / proprietary) | Not documented | Input Shaper and Phase Stepping with an integrated accelerometer[2] |
| Extruder | ||
| Type (direct drive / bowden) & design name | Dual-gear direct extruder with 2 fans (the Centauri machines use a 1-fan version)[1][11] | Nextruder direct drive with a 10:1 planetary gear system; all-metal hotend with an aluminium heatsink and a tool-free quick-swap nozzle system[2] |
| Gear ratio & drive gear material | Not documented | 10:1 planetary gearbox[2] |
| Hotend & Nozzle | ||
| Hotend design (proprietary/standard; quick-swap mechanism?) | Brass nozzle, 0.4 mm, with a titanium-alloy heat break[1] | Tool-free quick-swap nozzle system; Prusa brass high-flow CHT 0.4 mm pre-mounted plus an abrasive-resistant 0.4 mm nozzle in the box[2] |
| Max nozzle temp claimed AND firmware max temp limit (both values) | 300 C claimed max nozzle temperature[1] | 290 C claimed max nozzle temperature. The optional HT hotend that raises this to 400 C was announced for September 2026 availability, so it is not a shipping specification as of Aug 2026[2][5] |
| Heated Bed & Surface | ||
| Max bed temp claimed AND firmware limit | 100 C max heated bed temperature at 25 C ambient[1] | 120 C max heatbed temperature[2] |
| Bed surface (material, texture, coating), single/double-sided | PEI spring steel sheet; ELEGOO notes it is now upgraded to a dual-sided textured PEI + PLA-specific surface[1] | Magnetic heatbed with removable dual-sided PEI spring-steel sheets; a satin powder-coated sheet is supplied[2] |
| Leveling & Z-Offset | ||
| Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe) | Manual levelling combined with 121-point auto-levelling[1] | High-precision load-cell sensor - fully automatic first-layer calibration and mesh bed levelling restricted to the print area[2] |
| Filament Handling & Detection | ||
| Filament runout sensor (type, location) | Filament run-out sensor and power-loss recovery; no camera, no clog detection, no auto filament unloading[1] | Two filament sensors, plus a chamber door-open sensor and five Semitec thermistors[2] |
| Electronics & Power | ||
| Mainboard model & MCU (exact chip markings if teardowns exist) | ELEGOO describes it only as a "Klipper High-Speed Quiet Motherboard" - no board model or MCU is published[1] | Custom 32-bit xBuddy mainboard with an STM32 processor[2] |
| Total rated power draw | 320 W rated power; 24 V output; 110-120 V / 220-240 V input[1] | Standby 16 W, preheating about 630 W, average printing about 90 W on PLA and about 215 W on ASA (manufacturer figures)[2] |
| Firmware & Openness | ||
| Firmware base & current version (Klipper fork / Marlin fork / proprietary) | Klipper (ELEGOO names the system "Klipper" outright for the Neptune 4 Plus, rather than the ELEGOO OS branding used on the Centauri machines)[1][11] | Open-source Prusa Buddy firmware. The source tree (prusa3d/Prusa-Firmware-Buddy on GitHub) explicitly covers the Original Prusa MINI/MINI+, MK4, XL and CORE One and was last pushed to in August 2026. Updates are applied from a USB drive, through Prusa Connect or through the Prusa mobile app[12][13] |
| Connectivity, UI & Camera | ||
| Display: size, type, touch? | 4.3-inch colour capacitive touch screen[1] | 3.5-inch 65k-colour touch screen (CORE One family)[8] |
| On-device UI capabilities (model preview, per-object controls, etc.) | Colour capacitive touch UI; ElegooSlicer is recommended, with Orca and Cura also supported[1] | On-device touch UI with Prusa Connect and Prusa mobile app remote control[8] |
| WiFi (band/standard), Ethernet, USB ports, SD/flash-drive | USB, LAN and Wi-Fi[1] | Ethernet, NFC receiver and Wi-Fi through a physically removable module, which Prusa offers for high-security offline installations[2] |
| Materials Support | ||
| Officially supported filament list | PLA, TPU, PETG, ABS, ASA, Nylon[1] | PLA, PETG, Flex, PVA, PC, PP, CPE, PVB, and with Advanced Filtration also ABS, ASA, HIPS and PA[2] |
| Safety | ||
| Thermal runaway protection (verify in firmware source if at all possible) | Not documented | Open-source firmware on the xBuddy platform, which carries hardware overcurrent protection cutting heater and heatbed power above 15 A[14][12] |
| Noise & Power Consumption | ||
| Noise: claimed dB and independently measured dB (distance/method) | Operating sound is published as 65 dB or less - a manufacturer figure with no measuring distance or method given, so it is not comparable with a reviewer's dB reading[1] | Not documented |
| Reliability, Support & Ecosystem | ||
| Warranty length & support reputation (evidence, not vibes) | 12 months on brand-new machines and parts, but ELEGOO's own table excludes a long list of parts from that: PEI plate / build plate / nozzle kit / PTFE tube / heater / thermistor / hot end / packaging / manual / tools carry no warranty at all, and the extruder, extruder kit and printhead kit get 6 months. Certified pre-owned machines carry no warranty[15] | 2-year warranty for consumers in the EU, Liechtenstein, Switzerland, Norway and Iceland; 1 year for EU enterprises and 1 year for the rest of the world, which includes the United States. A printer bought from a reseller or privately carries 1 year from the original delivery date and is handled by the reseller. Prusa advertises 24/7 chat and e-mail support in seven languages[16][13] |
Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.
Sources for this comparison
- ELEGOO Neptune 4 Plus product page (full specification table) us.elegoo.com · 2026-08 · vendor
- Prusa CORE One L+ product page (CORE One L+ Technical Specifications) prusa3d.com · 2026-08 · vendor
- ELEGOO Neptune 4 Plus Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Max Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
- Prusa blog - Better Prints, Easier Use: Prusa XL+, CORE One L+ and CORE One+ (Gen 2), Our Big Product Update (published 13 August 2026) blog.prusa3d.com · 2026-08 · doc
- ELEGOO Neptune 4 Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
- Prusa 3D printers category listing with live e-shop prices, Aug 2026 prusa3d.com · 2026-08 · vendor
- Prusa CORE One+ (Gen 2) product page (Technical Parameters + CORE One+/MK4S/CORE One L comparison) prusa3d.com · 2026-08 · vendor
- ELEGOO Neptune 4 product page (Specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Max product page (Specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Centauri Carbon product page (full specification table) us.elegoo.com · 2026-08 · vendor
- GitHub - prusa3d/Prusa-Firmware-Buddy (firmware for MINI, MK4, XL and CORE One) github.com · 2026-08 · doc
- Original Prusa MK4S 3D Printer product page (Technical Parameters + CORE One+/MK4S/XL comparison table) prusa3d.com · 2026-08 · vendor
- Prusa blog - Original Prusa MK4 is here (published 29 March 2023), including the MK4 specification table and launch prices blog.prusa3d.com · 2026-08 · doc
- ELEGOO Refund & Warranty policy (warranty period table) us.elegoo.com · 2026-08 · vendor
- Prusa Knowledge Base - Warranty help.prusa3d.com · 2026-08 · doc