3D Printing InfoPrinter comparison
ELEGOO Neptune 4 Plus vs Prusa CORE One+ (Gen 2) INDX
Compare hardware, build volume, printing specifications, dated prices and sources.
2 selected · all documented properties
Open these two in the interactive comparisonMore ELEGOO Neptune 4 Plus comparisonsMore Prusa CORE One+ (Gen 2) INDX comparisons
| Property | ELEGOO Neptune 4 PlusBEDSLINGER | Prusa CORE One+ (Gen 2) INDXTOOLCHANGER |
|---|---|---|
| Identity | ||
| Brand | ELEGOO | Prusa Research |
| Class | BEDSLINGER | TOOLCHANGER |
| Identity & Market | ||
| Manufacturer & exact marketed model name (verify the exact product identity first) | ELEGOO Neptune 4 Plus[1] | Prusa CORE One+ (Gen 2) INDX, listed as "INDX 4-Tool" and "INDX 8-Tool" variants and as an "INDX 8-Tool Assembly kit"[2][3] |
| Release date (announcement and actual shipping) | Listed on the ELEGOO US store from 20 September 2023 (Shopify publish date), the same date as the Neptune 4 Max[4][5] | Announced as shipping on 20 August 2026 ("INDX, Shipping Has Started, Complete Printers Open for Orders"). Prusa's own front page in Aug 2026 announces "Prusa CORE One+ (Gen 2) INDX, Shipping Has Started, Complete Printers Open for Orders", with the assembled 8-tool machine quoted as shipping from 15 October and the kit from 29 October[6][2] |
| Street price (USD; dated snapshot per entry) | $309.00 on us.elegoo.com, Aug 2026, against a compare-at price of $425.00. Only a Ribbon-Cable printhead variant is listed for the Plus, unlike the Neptune 4 and 4 Max which also offer a Type-C version[4][7][5] | $1,850.93 for the INDX 4-Tool and $2,082.41 for the INDX 8-Tool on prusa3d.com, Aug 2026; the 8-Tool assembly kit is $1,804.63. Camera and filtration bundles run to $2,152.78[2][3] |
| Variants & sibling models — and how to tell them apart (spec-contamination risk) | Middle model of the Neptune 4 family. Against the base Neptune 4: bigger (320 x 320 x 385 mm), but a lower bed ceiling (100 C rather than 110 C) and much lower acceleration (12000 rather than 20000 mm/s2). Against the Max: smaller and lighter (14.4 kg against 18.1 kg) but with a higher bed ceiling (100 C against 85 C) and higher acceleration (12000 against 8000). Its Z drive is 2 lead screws with 2 tie rods, where the Centauri machines use 3 lead screws[1][8][9][10] | INDX is a multi-tool option on the CORE One+ (Gen 2) product page rather than a separate printer, sold in 4-tool and 8-tool configurations, plus a CORE One/+ INDX conversion kit for existing machines. All of the body, hotend, bed and electronics figures below come from that shared CORE One+ (Gen 2) page and were not published separately for the INDX machine, so treat them as platform figures. Prusa also sells the unrelated MMU3, which multiplexes five filaments through one nozzle[3][2] |
| Physical & Frame | ||
| Build volume X×Y×Z (mm) — advertised vs actually usable | 320 x 320 x 385 mm; printing platform 330 x 330 mm[1] | 250 x 220 x 270 mm - the CORE One+ (Gen 2) figure from the shared product page; Prusa does not publish a separate INDX build volume[3] |
| Machine footprint (mm) & clearance needed (cable/spool overhang) | 533 x 517 x 638 mm; ELEGOO also publishes a maximum size for machine activity of 578 x 750 x 860 mm including rack and tray, so allow 750 mm of depth[1] | 415 x 444 x 555 mm - shared CORE One+ (Gen 2) figure[3] |
| Net weight (kg) | 14.4 kg net, 16.65 kg gross[1] | Not documented |
| Frame construction & material | CNC-machined aluminium extrusion frame (Neptune 4 family)[8] | Not documented |
| Enclosure: open / enclosed; panel material; door/lid | Open frame, no enclosure[1] | Fully enclosed with active chamber heating up to 55 C (shared CORE One+ platform)[3] |
| Kinematics & Motion Hardware | ||
| Kinematics (bedslinger i3 / CoreXY / other) | Cartesian i3 bed-slinger[1] | CoreXY with a multi-tool head-changing system (INDX); Prusa's comparison table gives CoreXY for the CORE One family[3] |
| Z-axis: leadscrew count & type, sync mechanism, anti-backlash | Two lead screws with two tie rods[1] | Not documented |
| Stepper drivers (exact model e.g. TMC2209; UART/SPI; sensorless homing?) | "Silent Drive (All Axes)" is all ELEGOO publishes; the driver part number is not given on the product page[1] | Not documented |
| Speed & Acceleration | ||
| Max print speed (claimed, mm/s) | 30-500 mm/s printing speed, with 250 mm/s given by ELEGOO as the recommended figure - the 500 mm/s number is a ceiling, not a working speed[1] | Not documented |
| Recommended/typical print speed | 250 mm/s recommended printing speed (manufacturer figure)[1] | Not documented |
| Max acceleration (claimed, mm/s²) | 12000 mm/s2 maximum acceleration; default acceleration 5000 mm/s2[1] | Not documented |
| Extruder | ||
| Type (direct drive / bowden) & design name | Dual-gear direct extruder with 2 fans (the Centauri machines use a 1-fan version)[1][10] | Nextruder direct drive, 10:1 planetary gearbox (shared platform)[3] |
| Hotend & Nozzle | ||
| Hotend design (proprietary/standard; quick-swap mechanism?) | Brass nozzle, 0.4 mm, with a titanium-alloy heat break[1] | Not documented |
| Max nozzle temp claimed AND firmware max temp limit (both values) | 300 C claimed max nozzle temperature[1] | 290 C claimed max nozzle temperature, 400 C with the optional HT hotend (shared platform)[3] |
| Heated Bed & Surface | ||
| Max bed temp claimed AND firmware limit | 100 C max heated bed temperature at 25 C ambient[1] | 120 C max heatbed temperature (shared platform)[3] |
| Bed surface (material, texture, coating), single/double-sided | PEI spring steel sheet; ELEGOO notes it is now upgraded to a dual-sided textured PEI + PLA-specific surface[1] | Not documented |
| Leveling & Z-Offset | ||
| Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe) | Manual levelling combined with 121-point auto-levelling[1] | Load-cell sensor, fully automatic first-layer calibration (shared platform)[3] |
| Filament Handling & Detection | ||
| Filament runout sensor (type, location) | Filament run-out sensor and power-loss recovery; no camera, no clog detection, no auto filament unloading[1] | Filament sensors fitted (two on the CORE One+ platform)[3] |
| Multi-material/multi-color capability or official upgrade path | Not documented | INDX gives up to eight filaments; the alternative MMU3 handles five through a single nozzle[3] |
| Electronics & Power | ||
| Mainboard model & MCU (exact chip markings if teardowns exist) | ELEGOO describes it only as a "Klipper High-Speed Quiet Motherboard" - no board model or MCU is published[1] | Custom 32-bit xBuddy board with STM32 (shared platform)[3] |
| Total rated power draw | 320 W rated power; 24 V output; 110-120 V / 220-240 V input[1] | Not documented |
| Firmware & Openness | ||
| Firmware base & current version (Klipper fork / Marlin fork / proprietary) | Klipper (ELEGOO names the system "Klipper" outright for the Neptune 4 Plus, rather than the ELEGOO OS branding used on the Centauri machines)[1][10] | Open-source Prusa Buddy firmware. The source tree (prusa3d/Prusa-Firmware-Buddy on GitHub) explicitly covers the Original Prusa MINI/MINI+, MK4, XL and CORE One and was last pushed to in August 2026. Updates are applied from a USB drive, through Prusa Connect or through the Prusa mobile app[11][12] |
| Connectivity, UI & Camera | ||
| Display: size, type, touch? | 4.3-inch colour capacitive touch screen[1] | 3.5-inch 65k-colour touch screen (shared platform)[3] |
| On-device UI capabilities (model preview, per-object controls, etc.) | Colour capacitive touch UI; ElegooSlicer is recommended, with Orca and Cura also supported[1] | Not documented |
| WiFi (band/standard), Ethernet, USB ports, SD/flash-drive | USB, LAN and Wi-Fi[1] | Ethernet and Wi-Fi, USB drive (shared platform)[3] |
| Materials Support | ||
| Officially supported filament list | PLA, TPU, PETG, ABS, ASA, Nylon[1] | PLA, PETG, Flex, PVA, PC, PP, CPE, PVB; ABS, ASA, HIPS and PA as advanced materials in the heated chamber (shared platform)[3] |
| Noise & Power Consumption | ||
| Noise: claimed dB and independently measured dB (distance/method) | Operating sound is published as 65 dB or less - a manufacturer figure with no measuring distance or method given, so it is not comparable with a reviewer's dB reading[1] | Not documented |
| Reliability, Support & Ecosystem | ||
| Warranty length & support reputation (evidence, not vibes) | 12 months on brand-new machines and parts, but ELEGOO's own table excludes a long list of parts from that: PEI plate / build plate / nozzle kit / PTFE tube / heater / thermistor / hot end / packaging / manual / tools carry no warranty at all, and the extruder, extruder kit and printhead kit get 6 months. Certified pre-owned machines carry no warranty[13] | 2-year warranty for consumers in the EU, Liechtenstein, Switzerland, Norway and Iceland; 1 year for EU enterprises and 1 year for the rest of the world, which includes the United States. A printer bought from a reseller or privately carries 1 year from the original delivery date and is handled by the reseller. Prusa advertises 24/7 chat and e-mail support in seven languages[14][12] |
Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.
Sources for this comparison
- ELEGOO Neptune 4 Plus product page (full specification table) us.elegoo.com · 2026-08 · vendor
- Prusa 3D printers category listing with live e-shop prices, Aug 2026 prusa3d.com · 2026-08 · vendor
- Prusa CORE One+ (Gen 2) product page (Technical Parameters + CORE One+/MK4S/CORE One L comparison) prusa3d.com · 2026-08 · vendor
- ELEGOO Neptune 4 Plus Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Max Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
- Prusa blog - Prusa CORE One+ (Gen 2) INDX, Shipping Has Started, Complete Printers Open for Orders (published 20 August 2026) blog.prusa3d.com · 2026-08 · doc
- ELEGOO Neptune 4 Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 product page (Specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Max product page (Specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Centauri Carbon product page (full specification table) us.elegoo.com · 2026-08 · vendor
- GitHub - prusa3d/Prusa-Firmware-Buddy (firmware for MINI, MK4, XL and CORE One) github.com · 2026-08 · doc
- Original Prusa MK4S 3D Printer product page (Technical Parameters + CORE One+/MK4S/XL comparison table) prusa3d.com · 2026-08 · vendor
- ELEGOO Refund & Warranty policy (warranty period table) us.elegoo.com · 2026-08 · vendor
- Prusa Knowledge Base - Warranty help.prusa3d.com · 2026-08 · doc