3D Printing InfoPrinter comparison
ELEGOO Neptune 4 Plus vs FlashForge Creator 5 Pro
Compare hardware, build volume, printing specifications, dated prices and sources.
2 selected · all documented properties
Open these two in the interactive comparisonMore ELEGOO Neptune 4 Plus comparisonsMore FlashForge Creator 5 Pro comparisons
| Property | ELEGOO Neptune 4 PlusBEDSLINGER | FlashForge Creator 5 ProTOOLCHANGER |
|---|---|---|
| Identity | ||
| Brand | ELEGOO | FlashForge |
| Class | BEDSLINGER | TOOLCHANGER |
| Identity & Market | ||
| Manufacturer & exact marketed model name (verify the exact product identity first) | ELEGOO Neptune 4 Plus[1] | Flashforge Creator 5 Pro, sold as "Creator 5 Pro 4-Toolheads Enclosed Multi-Color 3D Printer"[2][3] |
| Release date (announcement and actual shipping) | Listed on the ELEGOO US store from 20 September 2023 (Shopify publish date), the same date as the Neptune 4 Max[4][5] | Launched alongside the Creator 5; one secondary source gives an estimated early-Q3 2026 release for the Pro specifically, while the joint launch report of 19 May 2026 covers both[6][7] |
| Launch MSRP (USD) | Not documented | $799 early-bird (deposit price, open until 20 June 2026); $949 standard MSRP[6][7] |
| Street price (USD; dated snapshot per entry) | $309.00 on us.elegoo.com, Aug 2026, against a compare-at price of $425.00. Only a Ribbon-Cable printhead variant is listed for the Plus, unlike the Neptune 4 and 4 Max which also offer a Type-C version[4][8][5] | $949.00 on flashforge.com, in stock, with $100 auto-applied in cart, checked Aug 2026[2][3] |
| Variants & sibling models — and how to tell them apart (spec-contamination risk) | Middle model of the Neptune 4 family. Against the base Neptune 4: bigger (320 x 320 x 385 mm), but a lower bed ceiling (100 C rather than 110 C) and much lower acceleration (12000 rather than 20000 mm/s2). Against the Max: smaller and lighter (14.4 kg against 18.1 kg) but with a higher bed ceiling (100 C against 85 C) and higher acceleration (12000 against 8000). Its Z drive is 2 lead screws with 2 tie rods, where the Centauri machines use 3 lead screws[1][9][10][11] | Enclosed version of the Creator 5. The $150 difference buys the enclosure, 65 °C active chamber heating, air filtration and engineering-material support. Build volume, toolhead count, speed and acceleration are identical to the Creator 5[2][6][7] |
| Physical & Frame | ||
| Build volume X×Y×Z (mm) — advertised vs actually usable | 320 x 320 x 385 mm; printing platform 330 x 330 mm[1] | 256 x 256 x 256 mm[6][7][12] |
| Machine footprint (mm) & clearance needed (cable/spool overhang) | 533 x 517 x 638 mm; ELEGOO also publishes a maximum size for machine activity of 578 x 750 x 860 mm including rack and tray, so allow 750 mm of depth[1] | Not documented |
| Net weight (kg) | 14.4 kg net, 16.65 kg gross[1] | Not documented |
| Frame construction & material | CNC-machined aluminium extrusion frame (Neptune 4 family)[9] | Rigid frame with a fully sealed enclosure; no dimensions or weight published[2][7] |
| Enclosure: open / enclosed; panel material; door/lid | Open frame, no enclosure[1] | Fully enclosed with door and top cover, with continuous airflow and dual-layer H13 HEPA plus coconut-shell activated carbon filtration[2][6][7] |
| Passive chamber temperature reached (if enclosed; measured values preferred) | Not documented | Up to 65 °C, actively heated with adaptive circulation (manufacturer claim — a heater setpoint, not a measured passive figure)[2][6][7] |
| Kinematics & Motion Hardware | ||
| Kinematics (bedslinger i3 / CoreXY / other) | Cartesian i3 bed-slinger[1] | CoreXY with four independent FlashSwap toolheads[6][7] |
| Z-axis: leadscrew count & type, sync mechanism, anti-backlash | Two lead screws with two tie rods[1] | Not documented |
| Stepper drivers (exact model e.g. TMC2209; UART/SPI; sensorless homing?) | "Silent Drive (All Axes)" is all ELEGOO publishes; the driver part number is not given on the product page[1] | Not documented |
| Speed & Acceleration | ||
| Max print speed (claimed, mm/s) | 30-500 mm/s printing speed, with 250 mm/s given by ELEGOO as the recommended figure - the 500 mm/s number is a ceiling, not a working speed[1] | 600 mm/s maximum (manufacturer claim)[2][6][7] |
| Recommended/typical print speed | 250 mm/s recommended printing speed (manufacturer figure)[1] | Not documented |
| Max acceleration (claimed, mm/s²) | 12000 mm/s2 maximum acceleration; default acceleration 5000 mm/s2[1] | 30,000 mm/s2 maximum (manufacturer claim)[6][7] |
| Extruder | ||
| Type (direct drive / bowden) & design name | Dual-gear direct extruder with 2 fans (the Centauri machines use a 1-fan version)[1][11] | Not documented |
| Hotend & Nozzle | ||
| Hotend design (proprietary/standard; quick-swap mechanism?) | Brass nozzle, 0.4 mm, with a titanium-alloy heat break[1] | Not documented |
| Max nozzle temp claimed AND firmware max temp limit (both values) | 300 C claimed max nozzle temperature[1] | Not documented |
| Stock nozzle material (brass / hardened steel / plated copper / composite tip) | Not documented | Hardened steel nozzles as standard[6][7] |
| Heated Bed & Surface | ||
| Max bed temp claimed AND firmware limit | 100 C max heated bed temperature at 25 C ambient[1] | 120 °C maximum (manufacturer claim)[7] |
| Bed surface (material, texture, coating), single/double-sided | PEI spring steel sheet; ELEGOO notes it is now upgraded to a dual-sided textured PEI + PLA-specific surface[1] | Not documented |
| Leveling & Z-Offset | ||
| Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe) | Manual levelling combined with 121-point auto-levelling[1] | Fully automatic calibration and levelling; probe technology not named[2] |
| Filament Handling & Detection | ||
| Filament runout sensor (type, location) | Filament run-out sensor and power-loss recovery; no camera, no clog detection, no auto filament unloading[1] | Not documented |
| Multi-material/multi-color capability or official upgrade path | Not documented | Four independent toolheads, physically swapped; FlashForge markets zero purge waste[2][6] |
| Cooling & Air Handling | ||
| Chamber/exhaust fan & filtration (activated carbon / HEPA) | Not documented | H13 HEPA plus coconut-shell activated carbon, dual layer, with continuous airflow[2][6][7] |
| Electronics & Power | ||
| Mainboard model & MCU (exact chip markings if teardowns exist) | ELEGOO describes it only as a "Klipper High-Speed Quiet Motherboard" - no board model or MCU is published[1] | Not documented |
| Total rated power draw | 320 W rated power; 24 V output; 110-120 V / 220-240 V input[1] | Not documented |
| Firmware & Openness | ||
| Firmware base & current version (Klipper fork / Marlin fork / proprietary) | Klipper (ELEGOO names the system "Klipper" outright for the Neptune 4 Plus, rather than the ELEGOO OS branding used on the Centauri machines)[1][11] | Not named by FlashForge. Supported slicers are Flash Studio, Orca-Flashforge and OrcaSlicer[7] |
| Connectivity, UI & Camera | ||
| Display: size, type, touch? | 4.3-inch colour capacitive touch screen[1] | Not documented |
| On-device UI capabilities (model preview, per-object controls, etc.) | Colour capacitive touch UI; ElegooSlicer is recommended, with Orca and Cura also supported[1] | Not documented |
| WiFi (band/standard), Ethernet, USB ports, SD/flash-drive | USB, LAN and Wi-Fi[1] | Dual-band Wi-Fi 2.4 GHz + 5 GHz, LAN, USB[6][7] |
| Camera: built-in / optional? Resolution & framerate (verify — marketing often omits real fps) | Not documented | 1080p camera at 30 fps[6][7] |
| Materials Support | ||
| Officially supported filament list | PLA, TPU, PETG, ABS, ASA, Nylon[1] | Not documented |
| Noise & Power Consumption | ||
| Noise: claimed dB and independently measured dB (distance/method) | Operating sound is published as 65 dB or less - a manufacturer figure with no measuring distance or method given, so it is not comparable with a reviewer's dB reading[1] | 55 dB claimed by the manufacturer. No independent measurement found; distance and method not stated[6] |
| Reliability, Support & Ecosystem | ||
| Warranty length & support reputation (evidence, not vibes) | 12 months on brand-new machines and parts, but ELEGOO's own table excludes a long list of parts from that: PEI plate / build plate / nozzle kit / PTFE tube / heater / thermistor / hot end / packaging / manual / tools carry no warranty at all, and the extruder, extruder kit and printhead kit get 6 months. Certified pre-owned machines carry no warranty[13] | Not documented |
Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.
Sources for this comparison
- ELEGOO Neptune 4 Plus product page (full specification table) us.elegoo.com · 2026-08 · vendor
- Flashforge Creator 5 Pro 4-Toolheads product page flashforge.com · 2026-08 · vendor
- Flashforge store search results for Creator 5 (live prices) flashforge.com · 2026-08 · vendor
- ELEGOO Neptune 4 Plus Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Max Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
- Flashforge Creator 5 and Creator 5 Pro launch report 3dprinting.com · 2026-08 · review
- Flashforge Creator 5 and 5 Pro breakdown antonmansson.com · 2026-08 · review
- ELEGOO Neptune 4 Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 product page (Specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Max product page (Specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Centauri Carbon product page (full specification table) us.elegoo.com · 2026-08 · vendor
- Flashforge printer buyer's guide, 5M to Creator 5 eolasprints.com · 2026-08 · review
- ELEGOO Refund & Warranty policy (warranty period table) us.elegoo.com · 2026-08 · vendor