3D Printing InfoPrinter comparison
ELEGOO Neptune 4 Max vs QIDI Q1 Pro
Compare hardware, build volume, printing specifications, dated prices and sources.
2 selected · all documented properties
Open these two in the interactive comparisonMore ELEGOO Neptune 4 Max comparisonsMore QIDI Q1 Pro comparisons
| Property | ELEGOO Neptune 4 MaxBEDSLINGER | QIDI Q1 ProCOREXY |
|---|---|---|
| Identity | ||
| Brand | ELEGOO | QIDI |
| Class | BEDSLINGER | COREXY |
| Identity & Market | ||
| Manufacturer & exact marketed model name (verify the exact product identity first) | ELEGOO Neptune 4 Max[1] | QIDI Q1 Pro, listed by QIDI as "Q1 Pro 3D Printer". QIDI traded as Qidi Tech until end-2024[2] |
| Release date (announcement and actual shipping) | Listed on the ELEGOO US store from 20 September 2023 (Shopify publish date)[3] | Not stated on QIDI's own product page; the page now carries a discontinuation notice instead of a launch date (checked Aug 2026)[2][4] |
| Street price (USD; dated snapshot per entry) | $389.00 on us.elegoo.com, Aug 2026, against a compare-at price of $559.99; Ribbon-Cable and Type-C printhead variants are the same price[3] | $499.00 on both qidi3d.com and us.qidi3d.com, checked Aug 2026 — but the listing is marked Sold Out and the page states "This model has been discontinued". qidi3d.com shows it against a $599.00 regular price; the US store shows compare-at $499.00[2][4] |
| Variants & sibling models — and how to tell them apart (spec-contamination risk) | Largest Neptune 4. The trade-off against the smaller models is easy to miss: the bed only reaches 85 C (against 100 C on the Plus and 110 C on the base Neptune 4) and acceleration is capped at 8000 mm/s2 (against 12000 and 20000), because of the mass of a 430 x 430 mm moving bed. Two printhead variants, Ribbon-Cable and Type-C, are sold under one SKU[1][5][6][3] | Succeeded by the QIDI Q2, which QIDI's own comparison on the Q1 Pro page distinguishes as 270x270x256 mm (vs 245x245x240), 370 °C hotend (vs 350 °C) and 65 °C chamber (vs 60 °C). Do not read Q2 figures onto the Q1 Pro[2][4] |
| Market position: superseded? successor announced? | Not documented | Discontinued and out of production; QIDI states spare parts and support for existing owners remain available. Replaced by the Q2[2][4] |
| Physical & Frame | ||
| Build volume X×Y×Z (mm) — advertised vs actually usable | 420 x 420 x 480 mm; printing platform 430 x 430 mm[1] | 245 x 245 x 240 mm advertised (QIDI). No independently measured usable envelope found[2][7] |
| Machine footprint (mm) & clearance needed (cable/spool overhang) | 658 x 632 x 740 mm; ELEGOO's maximum size for machine activity is 658 x 950 x 960 mm including rack and tray - allow nearly a metre of depth and height[1] | 477 x 467 x 489 mm machine dimensions (QIDI)[2][7] |
| Net weight (kg) | 18.1 kg net, 21.8 kg gross[1] | 17 kg net, 20.3 kg gross (QIDI). 3DJake lists the 20.3 kg figure as gross weight[2][7] |
| Frame construction & material | CNC-machined aluminium extrusion frame[1] | Metal CoreXY motion frame with panelled enclosure; QIDI publishes no frame-material breakdown for this model[2] |
| Enclosure: open / enclosed; panel material; door/lid | Open frame, no enclosure[1] | Fully enclosed with independent chamber heating to 60 °C; QIDI does not publish the panel materials for this model[2][7] |
| Passive chamber temperature reached (if enclosed; measured values preferred) | Not documented | 60 °C, actively heated (manufacturer claim — this is a heater setpoint, not a measured passive figure)[2][7] |
| Kinematics & Motion Hardware | ||
| Kinematics (bedslinger i3 / CoreXY / other) | Cartesian i3 bed-slinger[1] | CoreXY[7] |
| X-axis guide type (rods / linear rails / V-wheels; size) | Not documented | 10 mm linear steel rods with automatically tensioned belt (manufacturer description)[7] |
| Z-axis: leadscrew count & type, sync mechanism, anti-backlash | Two lead screws with two tie rods[8] | Independent dual Z lead-screw motors[7] |
| Stepper drivers (exact model e.g. TMC2209; UART/SPI; sensorless homing?) | "Silent Drive (All Axes)"; no driver part number published[8] | Not documented |
| Speed & Acceleration | ||
| Max print speed (claimed, mm/s) | 500 mm/s max toolhead speed (manufacturer claim)[1] | 600 mm/s, worded by QIDI as maximum tool-head speed (manufacturer claim, not a sustained printing speed)[2][7] |
| Recommended/typical print speed | 250 mm/s recommended printing speed against the 500 mm/s ceiling (ELEGOO's own figure); default acceleration is 4000 mm/s2[8] | Not documented |
| Max acceleration (claimed, mm/s²) | 8000 mm/s2 max toolhead acceleration (manufacturer claim) - the lowest in the Neptune 4 family[1] | <=20,000 mm/s2 (manufacturer claim)[2][7] |
| Extruder | ||
| Type (direct drive / bowden) & design name | Dual-gear direct extruder with 2 fans[8] | Direct-drive extruder with hardened steel gears[2][7] |
| Hotend & Nozzle | ||
| Hotend design (proprietary/standard; quick-swap mechanism?) | Brass nozzle, 0.4 mm, with a titanium-alloy heat break[8] | Tri-metal hotend with a ceramic heater plate and a bimetal nozzle, 0.4 mm standard[2][7] |
| Max nozzle temp claimed AND firmware max temp limit (both values) | 300 C claimed max nozzle temperature[1] | <=350 °C claimed. No firmware max_temp verified for this model[2][7] |
| Heated Bed & Surface | ||
| Max bed temp claimed AND firmware limit | 85 C max heated bed temperature at 25 C ambient - well below the 100-110 C of the smaller Neptunes, which limits ABS/ASA work despite them being on the compatibility list[1] | <=120 °C claimed. No firmware limit verified for this model[2][7] |
| Bed surface (material, texture, coating), single/double-sided | PEI spring steel sheet, now upgraded to a dual-sided textured PEI + PLA-specific surface; platform 430 x 430 mm[8] | Double-sided textured PEI plate on an aluminium substrate bed[2][7] |
| Leveling & Z-Offset | ||
| Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe) | Manual levelling combined with 121-point auto-levelling[8] | Automatic levelling; QIDI markets it as "hands-free automatic levelling" with dual sensors, without naming the probe technology[2] |
| Filament Handling & Detection | ||
| Filament runout sensor (type, location) | Filament detection and power-loss resume printing[1] | Filament run-out sensor fitted; QIDI also lists filament tangle detection without describing the mechanism[7] |
| Cooling & Air Handling | ||
| Part-cooling fan(s): count, size, ducting design | Not documented | Auxiliary part-cooling fan plus a chamber circulation fan (fan count and duct design not published)[7] |
| Electronics & Power | ||
| Mainboard model & MCU (exact chip markings if teardowns exist) | "Klipper High-Speed Quiet Motherboard" is all ELEGOO publishes[8] | Not documented |
| Input voltage (110/220 V, switch or auto) | 100-120 V / 220-240 V, 50/60 Hz[1][8] | 100-240 VAC, 50/60 Hz[7] |
| Total rated power draw | 320 W rated power, 24 V output[8] | 350 W plus 300 W for chamber heating (rated)[2][7] |
| Firmware & Openness | ||
| Firmware base & current version (Klipper fork / Marlin fork / proprietary) | Klipper[8] | Klipper, running on a 64-bit processor per QIDI. Exact fork and version not published on the product page[2] |
| Connectivity, UI & Camera | ||
| Display: size, type, touch? | 4.3-inch colour capacitive touch screen[8] | 4.3-inch touchscreen, 272 x 480[2][7] |
| On-device UI capabilities (model preview, per-object controls, etc.) | Colour capacitive touch UI; ElegooSlicer recommended, Orca and Cura supported[8] | Not documented |
| WiFi (band/standard), Ethernet, USB ports, SD/flash-drive | Wi-Fi, USB and WLAN file transfer[1] | Wi-Fi 6 (QIDI states "150M 2.4G") and USB 2.0. No Ethernet listed for this model[2][7] |
| Camera: built-in / optional? Resolution & framerate (verify — marketing often omits real fps) | Not documented | Built-in camera, up to 1080p, timelapse supported. Framerate not published[2][7] |
| Calibration Routines & QoL | ||
| Assembly level & time from unbox to first print | Not documented | Ships fully assembled[2] |
| Power-Loss & Interruption Recovery | ||
| Power-loss recovery: mechanism (how is state saved? capacitor / eeprom / file on shutdown?) | Not documented | Power-loss recovery listed as a feature; mechanism not published[7] |
| Materials Support | ||
| Officially supported filament list | PLA, TPU, PETG, ABS, ASA, Nylon - but note the 85 C bed ceiling against ABS and ASA[1] | QIDI lists compatibility with common filaments; storage 32 GB eMMC. No per-material list published on the current page beyond the general claim[2] |
| Noise & Power Consumption | ||
| Noise: claimed dB and independently measured dB (distance/method) | Operating sound published as 65 dB or less - a manufacturer figure with no distance or method stated[8] | Not documented |
| Reliability, Support & Ecosystem | ||
| Warranty length & support reputation (evidence, not vibes) | 12 months on brand-new machines and parts, but ELEGOO's own table excludes a long list of parts from that: PEI plate / build plate / nozzle kit / PTFE tube / heater / thermistor / hot end / packaging / manual / tools carry no warranty at all, and the extruder, extruder kit and printhead kit get 6 months. Certified pre-owned machines carry no warranty[9] | 1-year coverage, 14-day no-reason return, lifetime tech guidance (QIDI's standard terms as shown on its store)[10] |
Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.
Sources for this comparison
- ELEGOO Neptune 4 Max product page (Specification table) us.elegoo.com · 2026-08 · vendor
- QIDI Q1 Pro product page (global store) qidi3d.com · 2026-08 · vendor
- ELEGOO Neptune 4 Max Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
- QIDI Q1 Pro product page (US store) us.qidi3d.com · 2026-08 · vendor
- ELEGOO Neptune 4 product page (Specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Plus product page (full specification table) us.elegoo.com · 2026-08 · vendor
- QIDI Tech Q1 Pro technical data table 3djake.com · 2026-08 · vendor
- ELEGOO compare-products page, which embeds the full per-model specification JSON for every Neptune, Centauri and OrangeStorm machine us.elegoo.com · 2026-08 · vendor
- ELEGOO Refund & Warranty policy (warranty period table) us.elegoo.com · 2026-08 · vendor
- QIDI Max4 product page (US store) us.qidi3d.com · 2026-08 · vendor