3D Printing InfoPrinter comparison
ELEGOO Centauri 2 Combo vs UltiMaker Factor 4
Compare hardware, build volume, printing specifications, dated prices and sources.
2 selected · all documented properties
Open these two in the interactive comparisonMore ELEGOO Centauri 2 Combo comparisonsMore UltiMaker Factor 4 comparisons
| Property | ELEGOO Centauri 2 ComboCOREXY | UltiMaker Factor 4INDUSTRIAL |
|---|---|---|
| Identity | ||
| Brand | ELEGOO | UltiMaker |
| Class | COREXY | INDUSTRIAL |
| Identity & Market | ||
| Manufacturer & exact marketed model name (verify the exact product identity first) | ELEGOO Centauri 2 Combo - the Centauri 2 sold with the CANVAS multicolour unit[1] | UltiMaker Factor 4[2] |
| Release date (announcement and actual shipping) | Not documented | Announced 22 April 2024, shown at HANNOVER MESSE 2024 (22-26 April) and TCT Asia (7-9 May 2024)[2] |
| Launch MSRP (USD) | Not documented | Starting at approximately $20,000[2] |
| Variants & sibling models — and how to tell them apart (spec-contamination risk) | Same printer as the bare Centauri 2 for every motion, hotend, bed and electronics figure; what the Combo adds is 4-colour CANVAS printing, RFID filament detection, auto refill and auto tangle detection, and what it costs is bench space - 500 x 480 x 586 mm and 15.5 kg against 398 x 404 x 490 mm and 13.7 kg. Camera, LED lighting and air filter remain optional expansions on both[1] | Shares the 330 x 240 x 300 mm envelope with the UltiMaker S5, S7 and S8, which is the single most contaminated figure in UltiMaker's range. What separates the Factor 4 is the actively controlled 70 °C build volume, the climate-controlled 6-spool material station holding humidity below 15%, and HEPA filtration. UltiMaker also sells a Factor 4 Plus[2] |
| Physical & Frame | ||
| Build volume X×Y×Z (mm) — advertised vs actually usable | 256 x 256 x 256 mm; printing platform 260 x 260 mm[1] | 330 x 240 x 300 mm[2] |
| Machine footprint (mm) & clearance needed (cable/spool overhang) | 500 x 480 x 586 mm with the CANVAS unit fitted[1] | Not documented |
| Net weight (kg) | 15.5 kg net, 19 kg gross[1] | Not documented |
| Frame construction & material | Rigid aluminium frame (Centauri 2 platform)[1] | Not documented |
| Enclosure: open / enclosed; panel material; door/lid | Not documented | Enclosed with actively controlled chamber airflow and a HEPA filter[2] |
| Passive chamber temperature reached (if enclosed; measured values preferred) | Not documented | Build volume temperature controlled up to 70 °C with actively controlled chamber airflow (manufacturer specification)[2] |
| Kinematics & Motion Hardware | ||
| Kinematics (bedslinger i3 / CoreXY / other) | CoreXY with dual 4260 stepper motors[1] | Direct-drive dual extrusion; kinematic layout not stated in the source checked[2] |
| Z-axis: leadscrew count & type, sync mechanism, anti-backlash | Three lead screws with three linear guide rods[1] | Not documented |
| Speed & Acceleration | ||
| Max print speed (claimed, mm/s) | 500 mm/s or less, recommended 250 mm/s[1] | Not documented |
| Recommended/typical print speed | 250 mm/s recommended printing speed[1] | Not documented |
| Max acceleration (claimed, mm/s²) | 20000 mm/s2 maximum acceleration; default 10000 mm/s2[1] | Not documented |
| Extruder | ||
| Type (direct drive / bowden) & design name | Dual-gear direct extruder with one fan[1] | Direct-drive dual extrusion[2] |
| Filament diameter | Not documented | 2.85 mm[2] |
| Hotend & Nozzle | ||
| Hotend design (proprietary/standard; quick-swap mechanism?) | Brass-hardened steel nozzle, 0.4 mm, titanium-alloy heat break[1] | Not documented |
| Max nozzle temp claimed AND firmware max temp limit (both values) | 350 C claimed max nozzle temperature[1] | 340 °C maximum with the high-temperature print core (manufacturer claim)[2] |
| Heated Bed & Surface | ||
| Max bed temp claimed AND firmware limit | 110 C max heated bed temperature at 25 C ambient[1] | Not documented |
| Leveling & Z-Offset | ||
| Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe) | 121-point auto-levelling plus partial bed levelling[1] | Not documented |
| Filament Handling & Detection | ||
| Filament runout sensor (type, location) | Filament run-out sensor, clog detection, auto tangle detection, RFID filament detection, auto refill, auto filament unloading and power-loss recovery[1] | Not documented |
| Spool holder location & max spool size; drybox compatibility | Not documented | Automatic climate-controlled material handling and storage station holding humidity below 15%, storing up to six spools[2] |
| Multi-material/multi-color capability or official upgrade path | CANVAS four-colour printing with RFID filament identification and automatic refill - the defining difference from the bare Centauri 2[1] | Not documented |
| Cooling & Air Handling | ||
| Chamber/exhaust fan & filtration (activated carbon / HEPA) | Not documented | HEPA filter[2] |
| Electronics & Power | ||
| Mainboard model & MCU (exact chip markings if teardowns exist) | "Powerful Self-Developed Motherboard"[1] | Not documented |
| Total rated power draw | 1100 W at 220 V, 350 W at 110 V rated[1] | Not documented |
| Firmware & Openness | ||
| Firmware base & current version (Klipper fork / Marlin fork / proprietary) | ELEGOO OS; ElegooSlicer recommended[1] | Not documented |
| Connectivity, UI & Camera | ||
| Display: size, type, touch? | 5-inch colour capacitive touch screen[1] | Not documented |
| On-device UI capabilities (model preview, per-object controls, etc.) | Colour touch UI; STL, OBJ, 3MF and STEP input[1] | Not documented |
| WiFi (band/standard), Ethernet, USB ports, SD/flash-drive | USB and Wi-Fi[1] | Not documented |
| Materials Support | ||
| Officially supported filament list | Ideal: PLA, PETG, PLA-CF, TPU. Not recommended: ABS/ABS-CF, ASA/ASA-CF, PET/PET-CF, PETG-CF, PA/PA-CF, PC[1] | UltiMaker-branded PPS CF, PLA, Tough PLA, Nylon, PETG, PET CF and PVA, plus validated third-party materials from BASF Forward AM, Kimya, Polymaker, LEHVOSS and Jabil[2] |
| Reliability, Support & Ecosystem | ||
| Warranty length & support reputation (evidence, not vibes) | 12 months on brand-new machines and parts, but ELEGOO's own table excludes a long list of parts from that: PEI plate / build plate / nozzle kit / PTFE tube / heater / thermistor / hot end / packaging / manual / tools carry no warranty at all, and the extruder, extruder kit and printhead kit get 6 months. Certified pre-owned machines carry no warranty[3] | Not documented |
| Independently Measured Performance | ||
| Dimensional accuracy measurements (third-party, with numbers) | Not documented | Dimensional accuracy within +/-0.2 mm or +/-0.2% of feature nominal length; UltiMaker states it tested over 95% print-completion success. Manufacturer figures, not independent measurements[2] |
Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.
Sources for this comparison
- ELEGOO Centauri 2 product page (Centauri 2 Combo vs Centauri 2 side-by-side specification table) us.elegoo.com · 2026-08 · vendor
- UltiMaker Factor 4: technical specifications and pricing 3dprintingindustry.com · 2026-08 · review
- ELEGOO Refund & Warranty policy (warranty period table) us.elegoo.com · 2026-08 · vendor