3D Printing InfoPrinter comparison
Creality K2 vs ELEGOO Neptune 4 Plus
Compare hardware, build volume, printing specifications, dated prices and sources.
2 selected · all documented properties
Open these two in the interactive comparisonMore Creality K2 comparisonsMore ELEGOO Neptune 4 Plus comparisons
| Property | Creality K2COREXY | ELEGOO Neptune 4 PlusBEDSLINGER |
|---|---|---|
| Identity | ||
| Brand | Creality | ELEGOO |
| Class | COREXY | BEDSLINGER |
| Identity & Market | ||
| Manufacturer & exact marketed model name (verify the exact product identity first) | Creality K2[1] | ELEGOO Neptune 4 Plus[2] |
| Release date (announcement and actual shipping) | Not documented | Listed on the ELEGOO US store from 20 September 2023 (Shopify publish date), the same date as the Neptune 4 Max[3][4] |
| Street price (USD; dated snapshot per entry) | Not documented | $309.00 on us.elegoo.com, Aug 2026, against a compare-at price of $425.00. Only a Ribbon-Cable printhead variant is listed for the Plus, unlike the Neptune 4 and 4 Max which also offer a Type-C version[3][5][4] |
| Variants & sibling models — and how to tell them apart (spec-contamination risk) | Smallest of three K2 machines that share a product page. K2: 260 mm cube, no chamber heating, 100 C bed, 300 C nozzle, 8 GB storage, one air filter, one auxiliary cooling fan, 720p camera, no RFID reader, no Ethernet. K2 Pro: 300 mm cube, 60 C chamber, 110 C bed, RFID, Ethernet, 32 GB. K2 Plus: 350 mm cube, 350 C nozzle, 120 C bed, 30000 mm/s2, dual air filters, auto belt tensioning, 1080p camera, dual-band Wi-Fi. A K2 SE also exists as a separate model[1] | Middle model of the Neptune 4 family. Against the base Neptune 4: bigger (320 x 320 x 385 mm), but a lower bed ceiling (100 C rather than 110 C) and much lower acceleration (12000 rather than 20000 mm/s2). Against the Max: smaller and lighter (14.4 kg against 18.1 kg) but with a higher bed ceiling (100 C against 85 C) and higher acceleration (12000 against 8000). Its Z drive is 2 lead screws with 2 tie rods, where the Centauri machines use 3 lead screws[2][6][7][8] |
| Physical & Frame | ||
| Build volume X×Y×Z (mm) — advertised vs actually usable | 260 x 260 x 260 mm[1] | 320 x 320 x 385 mm; printing platform 330 x 330 mm[2] |
| Machine footprint (mm) & clearance needed (cable/spool overhang) | 404 x 436 x 545 mm[1] | 533 x 517 x 638 mm; ELEGOO also publishes a maximum size for machine activity of 578 x 750 x 860 mm including rack and tray, so allow 750 mm of depth[2] |
| Net weight (kg) | 18.3 kg[1] | 14.4 kg net, 16.65 kg gross[2] |
| Frame construction & material | Not documented | CNC-machined aluminium extrusion frame (Neptune 4 family)[6] |
| Enclosure: open / enclosed; panel material; door/lid | Enclosed, but with no chamber temperature control - Creality's table gives a max chamber temperature for the K2 Pro and K2 Plus and a dash for the K2. One air filter fitted[1] | Open frame, no enclosure[2] |
| Kinematics & Motion Hardware | ||
| Kinematics (bedslinger i3 / CoreXY / other) | CoreXY - Creality groups the K2 series with its CoreXY flagships and quotes 600 mm/s with step-servo motors on the X and Y axes[1] | Cartesian i3 bed-slinger[2] |
| Z-axis: leadscrew count & type, sync mechanism, anti-backlash | Not documented | Two lead screws with two tie rods[2] |
| Belts (type, width, e.g. Gates?) | Manual belt tensioning (the K2 Plus is auto-adjusted)[1] | Not documented |
| Stepper motors (frame size, step angle, brand if known) | Step-servo motors on the X and Y axes and the extruder (the K2 Plus adds them on Z)[1] | Not documented |
| Stepper drivers (exact model e.g. TMC2209; UART/SPI; sensorless homing?) | Not documented | "Silent Drive (All Axes)" is all ELEGOO publishes; the driver part number is not given on the product page[2] |
| Speed & Acceleration | ||
| Max print speed (claimed, mm/s) | 600 mm/s max printing speed (manufacturer claim)[1] | 30-500 mm/s printing speed, with 250 mm/s given by ELEGOO as the recommended figure - the 500 mm/s number is a ceiling, not a working speed[2] |
| Recommended/typical print speed | Not documented | 250 mm/s recommended printing speed (manufacturer figure)[2] |
| Max acceleration (claimed, mm/s²) | 20000 mm/s2 max acceleration (manufacturer claim)[1] | 12000 mm/s2 maximum acceleration; default acceleration 5000 mm/s2[2] |
| Extruder | ||
| Type (direct drive / bowden) & design name | Not documented | Dual-gear direct extruder with 2 fans (the Centauri machines use a 1-fan version)[2][8] |
| Hotend & Nozzle | ||
| Hotend design (proprietary/standard; quick-swap mechanism?) | Not documented | Brass nozzle, 0.4 mm, with a titanium-alloy heat break[2] |
| Max nozzle temp claimed AND firmware max temp limit (both values) | 300 C claimed max nozzle temperature[1] | 300 C claimed max nozzle temperature[2] |
| Heater cartridge power (W) | 70 W rated hotend power[1] | Not documented |
| Heated Bed & Surface | ||
| Max bed temp claimed AND firmware limit | 100 C max heatbed temperature - the lowest in the K2 family[1] | 100 C max heated bed temperature at 25 C ambient[2] |
| Bed surface (material, texture, coating), single/double-sided | Not documented | PEI spring steel sheet; ELEGOO notes it is now upgraded to a dual-sided textured PEI + PLA-specific surface[2] |
| Leveling & Z-Offset | ||
| Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe) | Smart auto levelling fitted; unlike the K2 Pro and Plus there is no nozzle AI camera, so there is no automatic flow-rate calibration[1] | Manual levelling combined with 121-point auto-levelling[2] |
| Filament Handling & Detection | ||
| Filament runout sensor (type, location) | Not documented | Filament run-out sensor and power-loss recovery; no camera, no clog detection, no auto filament unloading[2] |
| Cooling & Air Handling | ||
| Part-cooling fan(s): count, size, ducting design | One auxiliary cooling fan and one air filter[1] | Not documented |
| Electronics & Power | ||
| Mainboard model & MCU (exact chip markings if teardowns exist) | Not documented | ELEGOO describes it only as a "Klipper High-Speed Quiet Motherboard" - no board model or MCU is published[2] |
| Total rated power draw | Not documented | 320 W rated power; 24 V output; 110-120 V / 220-240 V input[2] |
| Firmware & Openness | ||
| Firmware base & current version (Klipper fork / Marlin fork / proprietary) | Creality OS, a Klipper derivative. Creality publishes the K2 firmware source as CrealityOfficial/K2_Series_Klipper on GitHub under GPL-3.0, last pushed March 2026[9][10][1] | Klipper (ELEGOO names the system "Klipper" outright for the Neptune 4 Plus, rather than the ELEGOO OS branding used on the Centauri machines)[2][8] |
| Connectivity, UI & Camera | ||
| Display: size, type, touch? | 4-inch touchscreen[1] | 4.3-inch colour capacitive touch screen[2] |
| On-device UI capabilities (model preview, per-object controls, etc.) | Touch UI with alarm sounds; no built-in RFID reader[1] | Colour capacitive touch UI; ElegooSlicer is recommended, with Orca and Cura also supported[2] |
| WiFi (band/standard), Ethernet, USB ports, SD/flash-drive | Wi-Fi 2.4 GHz, USB drive and a Creality 485 port; no Ethernet. 8 GB eMMC storage[1] | USB, LAN and Wi-Fi[2] |
| Camera: built-in / optional? Resolution & framerate (verify — marketing often omits real fps) | One chamber camera, 720p at 30 fps[1] | Not documented |
| Materials Support | ||
| Officially supported filament list | PLA, PETG, PET, ABS, PLA-CF - a shorter list than the K2 Pro and Plus, which add ASA, PA-CF and PPA-CF[1] | PLA, TPU, PETG, ABS, ASA, Nylon[2] |
| Safety | ||
| Thermal runaway protection (verify in firmware source if at all possible) | Not verified directly. Creality publishes the K2-series firmware as CrealityOfficial/K2_Series_Klipper (GPL-3.0); upstream Klipper ships the verify_heater thermal-runaway check, but whether the stock configuration enables it was not checked here[9][10] | Not documented |
| Noise & Power Consumption | ||
| Noise: claimed dB and independently measured dB (distance/method) | Not documented | Operating sound is published as 65 dB or less - a manufacturer figure with no measuring distance or method given, so it is not comparable with a reviewer's dB reading[2] |
| Reliability, Support & Ecosystem | ||
| Warranty length & support reputation (evidence, not vibes) | Creality's US store states "Up to 12-Month Warranty", a 14-day return and refund window and "Lifetime Customer Support" on its printer product pages. The "up to" wording means the term is not uniform across parts[11] | 12 months on brand-new machines and parts, but ELEGOO's own table excludes a long list of parts from that: PEI plate / build plate / nozzle kit / PTFE tube / heater / thermistor / hot end / packaging / manual / tools carry no warranty at all, and the extruder, extruder kit and printhead kit get 6 months. Certified pre-owned machines carry no warranty[12] |
Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.
Sources for this comparison
- Creality K2 series product page, including the Compare K2 Series table (K2 / K2 Pro / K2 Plus) creality.com · 2026-08 · vendor
- ELEGOO Neptune 4 Plus product page (full specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Plus Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Max Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 product page (Specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Max product page (Specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Centauri Carbon product page (full specification table) us.elegoo.com · 2026-08 · vendor
- GitHub API - CrealityOfficial/K2_Series_Klipper repository metadata (GPL-3.0, last push Mar 2026) api.github.com · 2026-08 · doc
- GitHub - CrealityOfficial organisation repositories (per-model firmware sources) github.com · 2026-08 · doc
- Creality US store - K1 3D Printer product page (live price, warranty and returns banner) store.creality.com · 2026-08 · vendor
- ELEGOO Refund & Warranty policy (warranty period table) us.elegoo.com · 2026-08 · vendor