3D Printing InfoPrinter comparison
Creality Ender-5 Max vs ELEGOO Neptune 4
Compare hardware, build volume, printing specifications, dated prices and sources.
2 selected · all documented properties
Open these two in the interactive comparisonMore Creality Ender-5 Max comparisonsMore ELEGOO Neptune 4 comparisons
| Property | Creality Ender-5 MaxCOREXY | ELEGOO Neptune 4BEDSLINGER |
|---|---|---|
| Identity | ||
| Brand | Creality | ELEGOO |
| Class | COREXY | BEDSLINGER |
| Identity & Market | ||
| Manufacturer & exact marketed model name (verify the exact product identity first) | Creality Ender-5 Max[1] | ELEGOO Neptune 4 (spec table "Product Model: Neptune 4")[2] |
| Release date (announcement and actual shipping) | Not documented | Listed on the ELEGOO US store from 27 May 2023 (Shopify publish date)[3] |
| Street price (USD; dated snapshot per entry) | $749.00 on store.creality.com, Aug 2026[4] | $219.00 on us.elegoo.com, Aug 2026, against a compare-at price of $249.00; both the Ribbon-Cable and Type-C printhead variants are the same price[3] |
| Variants & sibling models — and how to tell them apart (spec-contamination risk) | A cube-frame CoreXY machine where the bed drops in Z - Creality itself calls the class "bed droppers". Do not read Ender-3 V3 figures across: this is a 400 mm cube at 700 mm/s claimed, on a different frame entirely. An optional enclosure is sold for engineering filaments[1] | Two printhead variants of the same machine are sold under one SKU - "Ribbon-Cable Version" and "Type-C Version" - which use different printhead parts. Within the Neptune 4 family the numbers diverge sharply and get mixed up constantly: Neptune 4 is 225 x 225 x 265 mm with a 110 C bed and 20000 mm/s2; the Plus is 320 x 320 x 385 mm with a 100 C bed and 12000 mm/s2; the Max is 420 x 420 x 480 mm with an 85 C bed and only 8000 mm/s2. The Neptune 4 Pro is a separate model again[3][2][5][6] |
| Market position: superseded? successor announced? | Not documented | Still listed in ELEGOO's US store Neptune section in Aug 2026 alongside the 4 Pro, 4 Plus and 4 Max, but ELEGOO's current development is on the Centauri line[7] |
| Physical & Frame | ||
| Build volume X×Y×Z (mm) — advertised vs actually usable | 400 x 400 x 400 mm[1] | 225 x 225 x 265 mm; the PEI platform itself is 235 x 235 mm[2] |
| Machine footprint (mm) & clearance needed (cable/spool overhang) | Not documented | 475 x 445 x 515 mm. ELEGOO separately publishes a "maximum size for machine activity" of 475 x 550 x 735 mm including rack and tray - the depth to allow for is 550 mm, not 445 mm[2] |
| Net weight (kg) | Not documented | 8.3 kg net, 10.6 kg gross[2] |
| Frame construction & material | Not documented | CNC-machined aluminium extrusion frame[2] |
| Enclosure: open / enclosed; panel material; door/lid | Open frame as sold; Creality offers an optional enclosure to raise ambient temperature for engineering filaments[1] | Open frame, no enclosure[2] |
| Kinematics & Motion Hardware | ||
| Kinematics (bedslinger i3 / CoreXY / other) | CoreXY on a rigid all-metal frame, with the bed moving in Z (Creality's own term is a "bed dropper")[1] | Cartesian i3 bed-slinger[2] |
| X-axis guide type (rods / linear rails / V-wheels; size) | Precise linear rail on the X axis[1] | Not documented |
| Z-axis: leadscrew count & type, sync mechanism, anti-backlash | Z axis assisted by two linear rods[1] | Two lead screws (the Neptune 4 Plus and Max add two tie rods to the same arrangement)[8] |
| Stepper motors (frame size, step angle, brand if known) | 42-76 stepper motors on both the X and Y axes[1] | Not documented |
| Stepper drivers (exact model e.g. TMC2209; UART/SPI; sensorless homing?) | Not documented | "Silent Drive (All Axes)" is all ELEGOO publishes; no driver part number is given[8] |
| Speed & Acceleration | ||
| Max print speed (claimed, mm/s) | 700 mm/s max printing speed (Creality Lab claim, with Hyper Series filament recommended for quality at speed); the page also quotes 500 mm/s in the same block, so the two figures need care[1] | 500 mm/s max toolhead speed (manufacturer claim); the Neptune 4 Plus page for the same family states a recommended 250 mm/s[2][5] |
| Recommended/typical print speed | Not documented | 250 mm/s recommended printing speed against the 500 mm/s ceiling (ELEGOO's own figure)[8] |
| Max acceleration (claimed, mm/s²) | 20000 mm/s2 max acceleration (Creality Lab claim)[1] | 20000 mm/s2 max toolhead acceleration (manufacturer claim) - notably higher than the Plus at 12000 and the Max at 8000, because the moving mass is smaller[2][5][6] |
| Extruder | ||
| Type (direct drive / bowden) & design name | Direct-drive extruder with dual tempered gears, which Creality says passed 500 hours of continuous-extrusion durability testing[1] | Dual-gear direct extruder with 2 fans[8] |
| Hotend & Nozzle | ||
| Hotend design (proprietary/standard; quick-swap mechanism?) | Not documented | Brass nozzle, 0.4 mm, with a copper and titanium-alloy heat break - the Plus and Max use a titanium-alloy heat break only[8] |
| Max nozzle temp claimed AND firmware max temp limit (both values) | Not documented | 300 C claimed max nozzle temperature[2] |
| Heated Bed & Surface | ||
| Max bed temp claimed AND firmware limit | Not documented | 110 C max heated bed temperature[2] |
| Bed surface (material, texture, coating), single/double-sided | Not documented | PEI spring steel sheet, now upgraded by ELEGOO to a dual-sided textured PEI + PLA-specific surface[8] |
| Leveling & Z-Offset | ||
| Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe) | 64-point fully automatic bed levelling[1] | Manual levelling combined with 121-point auto-levelling; no full-auto calibration on this model[8] |
| Filament Handling & Detection | ||
| Filament runout sensor (type, location) | Not documented | Filament detection fitted; power-loss resume printing supported[2] |
| Electronics & Power | ||
| Mainboard model & MCU (exact chip markings if teardowns exist) | Not documented | ELEGOO describes it only as a "Klipper High-Speed Quiet Motherboard" - no board model or MCU published[8] |
| Input voltage (110/220 V, switch or auto) | Not documented | 115/230 V, 50/60 Hz on the product page; ELEGOO's compare page gives 110-120 / 220-240 VAC 50/60 Hz[2][8] |
| Total rated power draw | Not documented | 310 W rated power, 24 V output[8] |
| Firmware & Openness | ||
| Firmware base & current version (Klipper fork / Marlin fork / proprietary) | Not documented | Klipper (ELEGOO names the system "Klipper" outright for the Neptune 4 series, rather than the ELEGOO OS branding used on the Centauri machines)[8][9] |
| Connectivity, UI & Camera | ||
| Display: size, type, touch? | Not documented | 4.3-inch colour capacitive touch screen[8] |
| On-device UI capabilities (model preview, per-object controls, etc.) | Not documented | Colour capacitive touch UI; ElegooSlicer recommended, with Orca and Cura also supported[8] |
| WiFi (band/standard), Ethernet, USB ports, SD/flash-drive | WLAN multi-printer management for print farms, with a tri-colour indicator light[1] | LAN and USB file transfer; no Wi-Fi is listed for the base Neptune 4, unlike the Plus (USB/LAN/Wi-Fi) and Max (Wi-Fi/USB/WLAN)[2][5][6] |
| Materials Support | ||
| Officially supported filament list | Not documented | PLA, TPU, PETG, ABS, ASA, Nylon[2] |
| Noise & Power Consumption | ||
| Noise: claimed dB and independently measured dB (distance/method) | Not documented | Operating sound published as 60 dB or less - a manufacturer figure with no distance or method stated, so it is not comparable with an independently measured reading[8] |
| Reliability, Support & Ecosystem | ||
| Warranty length & support reputation (evidence, not vibes) | Creality's US store states "Up to 12-Month Warranty", a 14-day return and refund window and "Lifetime Customer Support" on its printer product pages. The "up to" wording means the term is not uniform across parts[10] | 12 months on brand-new machines and parts, but ELEGOO's own table excludes a long list of parts from that: PEI plate / build plate / nozzle kit / PTFE tube / heater / thermistor / hot end / packaging / manual / tools carry no warranty at all, and the extruder, extruder kit and printhead kit get 6 months. Certified pre-owned machines carry no warranty[11] |
Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.
Sources for this comparison
- Creality Ender-5 Max product page creality.com · 2026-08 · vendor
- ELEGOO Neptune 4 product page (Specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
- Creality US store - Ender-5 Max 3D Printer product page (live price) store.creality.com · 2026-08 · vendor
- ELEGOO Neptune 4 Plus product page (full specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Max product page (Specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO US store 3D printers collection (current line-up, Aug 2026) us.elegoo.com · 2026-08 · vendor
- ELEGOO compare-products page, which embeds the full per-model specification JSON for every Neptune, Centauri and OrangeStorm machine us.elegoo.com · 2026-08 · vendor
- ELEGOO Centauri Carbon product page (full specification table) us.elegoo.com · 2026-08 · vendor
- Creality US store - K1 3D Printer product page (live price, warranty and returns banner) store.creality.com · 2026-08 · vendor
- ELEGOO Refund & Warranty policy (warranty period table) us.elegoo.com · 2026-08 · vendor