3D Printing Info

Printer comparison

Elegoo Centauri Carbon 2 vs Stratasys F370

Compare hardware, build volume, printing specifications, dated prices and sources.

Elegoo Centauri Carbon 2 guideStratasys F370 guide

2 selected · all documented properties

Open these two in the interactive comparisonMore Elegoo Centauri Carbon 2 comparisonsMore Stratasys F370 comparisons
Elegoo Centauri Carbon 2 vs Stratasys F370 — documented properties and sources
PropertyElegoo Centauri Carbon 2COREXYStratasys F370INDUSTRIAL
Identity
BrandELEGOOStratasys
ClassCOREXYINDUSTRIAL
Identity & Market
Manufacturer & exact marketed model name (verify the exact product identity first)ELEGOO Centauri Carbon 2 Combo. Internal ids: slicer model_id: "Elegoo-CC2", printer_model: Elegoo Centauri Carbon 2, machine setting_id: ECC204 (0.4 nozzle), filament suffix @ECC2; firmware release folder printer-realase-2602101855; mainboard part number EF-M5-V1.0.073. Manual PDF title block: 11.201.0124B Centauri Carbon 2 Combo安装说明书-EN-V1.1[1][2]Stratasys F370, part of the Stratasys F123 Series[3]
Release date (announcement and actual shipping)Announced 2026-01-19; on sale 2026-01-26, 09:00 EST / 17:00 CET.[4][5][6][7]The F123 series spec sheet carried is revision 0721a (July 2021). Stratasys does not print a launch date on it[3]
Launch MSRP (USD)US $449.00. Regional launch MSRPs: €439, £339, C$619, A$999, ¥79,999[8][9]Not documented
Street price (USD; dated snapshot per entry)$379.00 USD displayed sale price on us.elegoo.com (badged −16 % against $449.00 list) as of 2026-08-19. The same page's machine-selector chip and the Shopify products.json variant both read $399.00 (compare-at $449.00). Certified pre-owned: $375.99. Amazon B0G4TPZPZM: $449 per Tom's price widget (Feb 2026) and $500 per Notebookcheck (Mar 2026)[2][10][11][12]Not documented
Variants & sibling models — and how to tell them apart (spec-contamination risk)Five live Centauri siblings on us.elegoo.com (2026-08-19): (1) Centauri Carbon 2 Combo $399/$379 — printer + CANVAS; 500×480×743 mm, 19.35 kg. (2) Centauri Carbon 2 (non-Combo) $349 — *identical printer, no CANVAS*; 398×404×490 mm, 17.5 kg. (3) Centauri 2 Combo $329. (4) Centauri 2 $279. (5) Centauri Carbon (CC1) $419.99. Plus ELEGOO × emoji® CC2 Combo $449 (cosmetic edition). CANVAS standalone: $150 (with cover) / $120 (without); CC2-non-Combo + CANVAS-no-cover bundle $389[11][13][14]Top of the series and the only one with ABS-ESD7, PC-ABS and Diran 410MF07, an Insight software licence, and ProtectAM with US DoD STIG compliance on Red Hat Enterprise Linux. Cabinet and weight are identical to the F170 and F270, so footprint tells you nothing about which model you have[3]
Market position: superseded? successor announced?Current flagship of the Centauri line; no CC3 or CC2 successor announced. Elegoo has widened the line *below* it (Centauri 2 / Centauri 2 Combo, Jun–Jul 2026) and continues shipping CC2 OTA firmware (latest catalogued v02.00.02.00, 2026-05-28). Benchmarked by reviewers against Bambu Lab P1S Combo ($549), Bambu P2S Combo ($799), Creality K2 Combo ($549), Creality SPARKX i7 ($399) and Anycubic Kobra X[11][15]Not documented
Physical & Frame
Build volume X×Y×Z (mm) — advertised vs actually usableAdvertised 256 × 256 × 256 mm; platform 260 × 260 mm. Firmware agrees exactly: x_range=0,256, y_range=0,256, z_range=0,256. Axis travel exceeds the print area: X position_min=-2.1 → position_max=256.5; Y -2.1 → 270.0; Z -10 → 258.0. Slicer printable_area 256×256, printable_height 256, with a bed_exclude_area of 246×0 → 256×20 mm[16]355 x 254 x 355 mm (14 x 10 x 14 in)[3]
Machine footprint (mm) & clearance needed (cable/spool overhang)Combo: 500 × 480 × 743 mm (= 19.68 × 18.89 × 29.25 in). Bare CC2: 398 × 404 × 490 mm. Package: Combo 490 × 495 × 560 mm (gross 23.8 kg); bare CC2 465 × 460 × 560 mm; CC1 480 × 475 × 560 mm. Extra clearance needed to the right for four side-mounted spool holders and above for the tophat[17]1,626 x 864 x 711 mm (64 x 34 x 28 in)[3]
Net weight (kg)Combo: 19.35 kg (gross 23.8 kg). Bare CC2: 17.5 kg (gross 20.4 kg)[18]124 kg (F120) or 227 kg with consumables (F170, F270, F370)[3]
Frame construction & materialIntegrated die-cast aluminium frame and chassis, SPCC steel panels, injection-moulded covers; metal side panels and a glass front door[2]Fully enclosed office/classroom-grade cabinet, factory assembled[3]
Enclosure: open / enclosed; panel material; door/lidFully enclosed. Metal side panels + glass front door + removable "tophat" lid (acrylic/Perspex) that also covers the CANVAS module; a thermal cover ships in the box. Rear carries a servo-actuated exhaust grille and an air filter[19]Enclosed build chamber[3]
Passive chamber temperature reached (if enclosed; measured values preferred)MEASURED: peak ~47 °C, sustained ~45 °C, from a 17 °C ambient, with the tall cover fitted. Aurora Tech placed an independent thermometer inside the chamber during a standard-ABS print in a 17 °C garage: the internal temperature reaches ~35 °C shortly after the print starts, exceeds 40 °C after about an hour, peaks at ~47 °C, then settles at ~45 °C for the remainder as the part grows and the bed descends. On a separate, smaller PA-CF job the enclosure read ~41 °C near the end. Aurora Tech is based in Danville, California, so this was obtained on 110-120 V mains, i.e. on the ~250 W bed (see I2), which makes the figure directly applicable to US buyers. Firmware-verified surrogate, consistent with the measurement: a chamber thermistor exists ([ztemperature_sensor box], NTC 100 K B3950, max_temp=110, over-temp cutoff ot_box=100) and the chamber fan is thermostatically staged at T0=30, T1=38, T2=37, T3=40, T4=45 C. An owner reports being able to request a slicer-side chamber 50 C target / 45 C minimum[20][21]Not documented
Kinematics & Motion Hardware
Kinematics (bedslinger i3 / CoreXY / other)CoreXY — kinematics=corexy. Fixed gantry; bed moves in Z[22]Not documented
X-axis guide type (rods / linear rails / V-wheels; size)Ø8 mm hardened smooth rods with LM8LUU / LMS8LUU linear ball bearings. Not linear rails, not V-wheels[2]Not documented
Y-axis guide typeSame as X: Ø8 mm smooth rods + LM8LUU/LMS8LUU linear bearings[23]Not documented
Z-axis: leadscrew count & type, sync mechanism, anti-backlash3 lead screws + 3 linear guide rods, all driven from a single Z stepper via a belt. Firmware declares exactly one [stepper_z]: rotation_distance=8 (8 mm Z per motor rev), run_current=1.0, position_min=-10, position_max=258. Z endstop is a physical optical limit switch (endstop_pin=^PB10), *plus* the load-cell probe for Z-zero. No anti-backlash nut documented[1]Not documented
Belts (type, width, e.g. Gates?)2M-pitch (2 mm), 6 mm-wide open-ended timing belt — BOM part 2M-W6开口同步带 — with dedicated XY belt-tensioning springs (X/Y轴同步带张紧弹簧), tensioner-idler brackets (XY轴皮带张紧惰轮支架) and belt clamps (XY皮带固定卡片). No Gates branding in any source. Firmware-consistent: rotation_distance=39.872 on X and Y[24]Not documented
Stepper motors (frame size, step angle, brand if known)X and Y: two 42 × 60 mm NEMA 17 (BOM 42-60步进电机; Elegoo: "Dual 4260 stepper motors independently drive the X and Y axes"). Extruder: round 36 × 20 mm NEMA-14-class, P/N BJY36D12-04V28, Shenzhen Keli Motor Ltd (BOM 36x20圆形步进电机). CANVAS: 4 × permanent-magnet steppers with worm gearboxes, Shenzhen Wanzhida Motor. Step angle: full_steps_per_rotation is absent from the config → Klipper default 200 steps/rev = 1.8°[2][25][26]Not documented
Stepper drivers (exact model e.g. TMC2209; UART/SPI; sensorless homing?)TMC2209 throughout, UART, with sensorless homing on X and Y. X: uart_pin=PE6, tx_pin=PE7, run_current=1.2, hold_current=0.8, driver_SGTHRS=130, diag_pin=PF0, endstop_pin=tmc2209_stepper_x:virtual_endstop. Y: same currents, SGTHRS=130, diag_pin=PF3. Z: run_current=1.0, SGTHRS=120, but uses the physical endstop. Extruder (on toolhead MCU): uart_pin=toolhead:PB11, uart_address=2, run_current=0.8, hold_current=0.2. sense_resistor=0.1 throughout. CANVAS uses 4 × AT8833 (DRV8833 clone) — not TMC[1][27]Not documented
Microstepping / interpolation settings (firmware evidence)Microsteps=16 on every axis, with interpolate=True on every TMC2209 (1/16 commanded, interpolated to 1/256 in-driver)[28]Not documented
Speed & Acceleration
Max print speed (claimed, mm/s)≤500 mm/s[29]Not documented
Recommended/typical print speedElegoo's own spec table says "Recommended 250 mm/s". Reviewer practice: Tom's ran 160 mm/s avg (multicolour PLA), 150 mm/s (PETG), 100 mm/s (PAHT-CF and PC), 50 mm/s (TPU). 3DwithUS used 300 mm/s inner / 250 mm/s outer walls[30]Not documented
Max travel speed500 mm/s — max_velocity=500 is a global ceiling covering travel; slicer sets machine_max_acceleration_travel=20000. Z far slower: max_z_velocity=50[31]Not documented
Max acceleration (claimed, mm/s²)20 000 mm/s² maximum; 10 000 mm/s² "Default Acceleration"[32]Not documented
Firmware velocity limit (`max_velocity` or Marlin equivalent — exact value)Max_velocity= 500; max_z_velocity= 50[33]Not documented
Firmware acceleration limit (`max_accel` / `DEFAULT_MAX_ACCELERATION` — exact value)Max_accel= 20000; max_z_accel= 1200. Slicer: machine_max_acceleration_extruding=20000, machine_max_acceleration_z=500. Start g-code clamps outer walls with M204 S{min(20000, max(1000, outer_wall_acceleration))}[34]Not documented
Jerk / square-corner-velocity setting (exact value)Square_corner_velocity=9. (9 mm/s, ~1.8× Klipper's 5.0 default). Slicer mirrors it: machine_max_jerk_x = machine_max_jerk_y = 9, machine_max_jerk_e = 1[35]Not documented
Max volumetric flow claimed (mm³/s)The vendor slicer profiles are the operative claim — PLA 21, ABS 18, PC 16, PLA-CF 16, PETG-CF 12, PETG 11, PET-CF 8, PAHT-CF 6, TPU 95A 3.2 mm³/s. Elegoo publishes no headline flow figure[36]Not documented
Max volumetric flow independently measured (mm³/s, method)Not published[37]Not documented
Real-world speed benchmarks (e.g. Benchy time from third-party tests)No rigorously-specified Benchy exists for the CC2. Actual data points: CreativeBloq ~40 min for a colour-split multi-part Benchy; 3DwithUS ~2 h for a 4-colour Benchy and ~35 min for the built-in single-colour "Little Buddha"; VoxelMatters "just over 20 minutes" for the *same* Buddha; Tom's 4 h 55 min / 7 Baby Chameleons @0.2 mm, 160 mm/s avg; 4 h 20 min PETG Slinky @0.2 mm, 150 mm/s; 6 h 06 min / 7 PC utility knives @0.2 mm, 100 mm/s; 2 h 12 min PAHT-CF part @0.2 mm, 100 mm/s. Aggregator smith3d quotes "~31 min at 500 mm/s / ~48 min at 300 mm/s" and an "18 min 19 s speed-optimised Benchy on the Centauri platform" — provenance unverifiable, and "the Centauri platform" may mean CC1[38][30][39][40]Not documented
Vibration Compensation / Input Shaping
Input shaping supported? Implementation (Klipper IS / Marlin ZV / proprietary)Yes — stock Klipper-style [input_shaper] + [resonance_tester] in Elegoo's C++ Klipper re-implementation. Marketed as "Active Vibration Compensation"[2]Not documented
Accelerometer: present? model (ADXL345 / LIS2DW12 / …), location(s), countOne accelerometer: a single [lis2dw] on the toolhead, software-SPI (cs_pin=toolhead:PA4, sclk=PA5, mosi=PA7, miso=PA6, 5 MHz, axes_map=x,y,z). Teardown identifies it as LIS2DW12 on SPI1 with labelled test points CS/SCLK/MOSI/MISO = PA4/PA5/PA7/PA6 — an exact pin-for-pin match to the config[25]Not documented
Calibration mode: automatic per-print / user-run routine / factory-fixed valuesUser/self-check-run routine that stores results — NOT per print. [resonance_tester] carries shaper_calibrate_gcode=G28\n, i.e. a discrete calibration action. The per-print machine_start_gcode contains BED_MESH_CALIBRATE but no shaper calibration. Notebookcheck: "the one click calibration takes care of optimizing the nozzle, bed level, and vibration compensation. The whole calibration process takes about 26 to 27 minutes"[12]Not documented
Shaper type & default frequencies (firmware evidence preferred)Shaper_type_x = mzv, shaper_freq_x = 53.6; shaper_type_y = mzv, shaper_freq_y = 44.8; damping_ratio_x = damping_ratio_y = 0.1. Search space: min_freq=5, max_freq=90, accel_per_hz=100, hz_per_sec=2, max_smoothing=1, probe point 128,128,5[41]Not documented
Effectiveness evidence (ringing/VFA tests from reviews). TechRadar's structured test scores XY resonance 2.5 / 5 and Z-axis alignment 2.5 / 5 — by far the weakest two of its eight sub-scores. Against that, Tom's saw "no color bleeding using the default purge values" on a 7-part multicolour plate; CreativeBloq: "layer lines are barely visible, corners and edges are sharp" and "there were very few of those annoying wispy bits of filament you can get when the nozzle lifts off"; 3DwithUS: "All lettering came out sharp and clearly defined"[42]Not documented
Extrusion Pressure Control
Pressure advance (Klipper) / linear advance (Marlin) supported?Yes — Klipper-style pressure advance[43]Not documented
Enabled by default? Factory value? (firmware evidence)Yes. Firmware default pressure_advance=0.04. The slicer then overrides it per material: PLA/ABS 0.04, PC 0.052, PAHT-CF 0.052, TPU 95A 0.1[44]Not documented
Auto-calibration for PA/LA? How does it work?Marketed, but no per-print PA routine exists in the shipped g-code. machine_start_gcode contains no PA calibration call; there is no PA macro in [g180]. Elegoo's product page nonetheless advertises "Pressure Advance Calibration" as a headline feature[2]Not documented
Any physical nozzle pressure / load-cell extrusion sensing?No. A load cell exists ([load_cell_probe], CS1237 24-bit ADC on the bed MCU, 4-wire Wheatstone strain-gauge bridge) but it is wired to the bed as the Z probe — it is not read for extrusion force. Filament *presence* and *motion* are sensed optically/by encoder instead[45]Not documented
Related settings (PA smooth time etc., firmware values)Pressure_advance_smooth_time=0.04 (Klipper default is 0.040 — unchanged). Extruder also sets instantaneous_corner_velocity=1, max_extrude_only_distance=300, max_extrude_only_velocity=60, max_extrude_only_accel=5000, max_extrude_cross_section=9999999, and retract_restart_extra_toolchange=['0.5'] in the slicer[46]Not documented
Extruder
Type (direct drive / bowden) & design nameDirect drive, "Dual-Gear Direct Extruder (1 Fan)" (Elegoo's own wording). On the Combo the extruder additionally carries a filament multiplexer (4-into-1 hub) and a filament cutter[26][25]Not documented
Gear ratio & drive gear materialGear_ratio=52:10 (5.2 : 1), rotation_distance=28.8. Hobbed gear: 10 mm nominal diameter, SDK11 tool steel[25]Not documented
Filament diameter1.75 mm[47]Not documented
Filament path (PTFE-lined? all-metal? reverse bowden?)Combo: four PTFE Bowden tubes run from CANVAS on top of the machine to a 4-in-1 filament hub / multiplexer screwed to the toolhead; from the multiplexer a 4 mm OD metal tube feeds the extruder, replacing the reverse-Bowden PTFE. Melt zone is all-metal with a titanium-alloy heat break — no PTFE at the melt zone. Non-Combo: conventional reverse-Bowden PTFE[26]Not documented
Claimed extrusion force / grip (if published)Elegoo publishes no extrusion-force figure[48]Not documented
Auto load/unload routineYes, fully automatic in both directions. [filament_load_unload] defines two-stage load and unload macros; the load routine heats to 250 °C (M104 S250 / M109 S250), parks at the purge station via G180 S800, then runs G180 S812 → S811 → S810 → S800; unload runs G180 S813 (cutter position), retracts E-0.8, then E-100 F600. CANVAS auto-grabs filament on insertion; Elegoo lists "Auto Filament Unloading: Yes"[49]Not documented
Hotend & Nozzle
Hotend design (proprietary/standard; quick-swap mechanism?)Proprietary Elegoo hotend, shared design lineage with CC1 but with a higher-temperature heater. The hotend sits on a main toolhead PCB plus a separate "supplementary board" (2×4 pin) that breaks out thermistor, heater and hotend fan. No tool-less quick-swap mechanism is documented; the nozzle is a separate serviceable part[25][50]Not documented
Max nozzle temp claimed AND firmware max temp limit (both values)Claimed 350 °C. Firmware limit max_temp=365 in the shipping config (printer_dsp.cfg L134), with sensor_type=NTC R25 350 and min_temp=-100. The non-shipping printer.cfg in the same repo sets max_temp=600 with sensor_type=NTC 100K beta 4300 — this drew a public GitHub issue[51]Not documented
Heater cartridge power (W)60 W ceramic plate-type PTC heater, ~9.6 Ω (24 V → 24²/9.6 = 60 W, self-consistent)[25]Not documented
Temperature sensor type (thermistor model / thermocouple) & ratingFirmware: sensor_type=NTC R25 350 (an Elegoo-defined curve; the name implies R25 characterisation to 350 °C), on sensor_pin=toolhead:PA3. Teardown: "Glass bead NTC-200k", beta unknown ("likely 3950 or 4300"). The non-shipping printer.cfg uses NTC 100K beta 4300. Bed and chamber both use NTC 100 K β3950[25]Not documented
Stock nozzle size & sizes included in box0.4 mm fitted; only 0.4 mm supplied. No spare nozzle in the box (the box does include a "Spare Nozzle Wiper" and an unclogging pin, which is a different thing)[52]Not documented
Stock nozzle material (brass / hardened steel / plated copper / composite tip)Bimetal: brass body with a hardened-steel tip. Elegoo's own part description: "0.4 mm nozzles with brass bodies for fast, even heating and hardened steel tips for long-lasting wear resistance". BOM part 黄铜硬化钢喷嘴 (brass hardened-steel nozzle)[53]Not documented
Nozzle mount standard (V6 / MK8 / Unicorn / proprietary) & swap procedureProprietary Elegoo Centauri-series nozzle (fits the whole Centauri family — CC1, CC2, Centauri 2 — per the part name "for Centauri Series"). Not V6/MK8/Unicorn. No documented tool-less swap; the manual's maintenance guidance is limited to clearing residue with the supplied unclogging pin[50][25]Not documented
Available nozzle sizes/materials (official + third-party compatibility)Official: 0.2 / 0.4 / 0.6 / 0.8 mm, all brass-body + hardened-steel-tip. "Multi-Size Brass Hardened Steel Nozzle Kit for Centauri Series" ($24.99) contains all four; single 0.4 mm kit $22.99. Slicer ships full profile sets for all four sizes (nozzle_diameter: "0.4;0.2;0.6;0.8", 21 process profiles spanning 0.08–0.48 mm layers). Third-party: none documented[54]Not documented
All-metal hotend? PTFE near melt zone?Yes, all-metal, with a titanium-alloy heat break. No PTFE at the melt zone — PTFE stops at the multiplexer/hub above the extruder[55][26]Not documented
Melt-zone / high-flow design details (CHT-style, length)In detail. Known: plate-type ceramic PTC heater (60 W), titanium heat break, 3010 axial heat-break fan (12 000 rpm, 0.10 A @24 V), silicone sock, bimetal nozzle. No melt-zone length, bore diameter, or CHT/high-flow geometry is published or measured anywhere[25]Not documented
Heated Bed & Surface
Max bed temp claimed AND firmware limitClaimed 110 °C (at 25 °C ambient). Firmware max_temp=125, with a separate hardware over-temp parameter ot_bed=130. min_temp=-100[56]Not documented
Bed heater type (DC/AC mains) & wattageAC mains-powered heater switched by a solid-state relay (SSR) board — NOT a 24 V DC bed. Measured resistance ~48.4 Ω; 1000 W @ 220 V / 250 W @ 110 V. Safety: ground present + thermal fuse. Control is a PWM signal (heater_pin=PG13, pwm_cycle_time=0.016 ≈ 62.5 Hz) into the SSR; the mainboard's HBED connector carries only the control signal[45][30][57]Not documented
Heat-up time to 60°C (measured preferred)For the CC2. No reviewer timed it[58]Not documented
Bed surface (material, texture, coating), single/double-sidedDual-sided spring-steel flex plate: textured PEI on one side, a "PLA-Specific" smooth surface on the other. Plate stack: 3 mm aluminium plate + 1.5 mm magnetic sheet. Platform 260 × 260 mm[45]Not documented
Magnetic removable plate? Spare plate availability & costYes, magnetic removable. Spares: "Dual-Sided Build Plate for Centauri Series" $22.99; 3-pack $39.99; an older revision "(Original)" $21.99[59][11]Not documented
Bed thermal uniformity (third-party thermal imaging if available)Not published[60]Not documented
Leveling & Z-Offset
Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe)Load-cell / strain-gauge nozzle-touch probe in the bed. [load_cell_probe] with sensor_type=cs1237 (CS1237 24-bit ADC) on the dedicated bed MCU (sclk_pin=bed_sensor:PA5, dout_pin=bed_sensor:PA4, gain=A-128, sample_rate=1280). Calibration: counts_per_gram=25.0, trigger_force=200.0 g, safety_limit=1200.0 g, trigger_count=5. Bed hardware: 4-wire Wheatstone strain-gauge bridge with a single amplifier IC[45]Not documented
Mesh grid size (probe point count — firmware evidence)Probe_count=11,11 → 121 points, mesh_min=6,6, mesh_max=246,246, mesh_pps=3,3, algorithm=bicubic, bicubic_tension=0.2, mesh travel speed=500.0, horizontal_move_z=3.0, calibrate_accel=20000, move_check_distance=1.0, split_delta_z=0.01. Slicer mirrors: bed_mesh_min 10,10, bed_mesh_max 243,245, bed_mesh_probe_distance 22,22[61]Not documented
Auto Z-offset (nozzle-touch etc.) or manual (paper method)?Fully automatic nozzle-touch Auto Z-offset — no paper method. z_offset=0 in the probe section (the load cell defines Z=0 by contact). Additionally a nozzle-thermal-expansion compensation table exists: [z_compensation] with nozzle_temp_start=100, nozzle_temp_end=250, nozzle_temp_diff=10, fix_ref_temperature=140.0, and a 16-entry measured offset table nozzle_calibrate_datas = -0.039173 … 0.072890 mm[2]Not documented
Manual leveling screws/knobs present?None documented. The manual's assembly chapter has no bed-levelling-screw step; the bed ships locked by three transport screws that are removed, not adjusted[62]Not documented
Gantry-leveling / Z-tilt routine?No — and structurally impossible in software. There is one Z stepper driving three belted lead screws, so there is no per-screw actuator to tilt. No [z_tilt] or [quad_gantry_level] section exists in either config[63]Not documented
Leveling workflow (forced per print? saved mesh? adaptive mesh?)Mesh is measured on every print by default. machine_start_gcode unconditionally issues BED_MESH_CALIBRATE mesh_min=… mesh_max=… ALGORITHM=… PROBE_COUNT=… ADAPTIVE=0 ADAPTIVE_MARGIN=0 FROM_SLICER=1 before G28 and heating. Adaptive meshing exists but is off in the default profile (ADAPTIVE=0); [g180] macros S8/S910 implement BED_MESH_PROFILE LOAD=ADAPTIVE. A saved default profile also exists (G180 S7 → BED_MESH_PROFILE LOAD=default). Elegoo additionally lists "Partial Bed-Leveling" as a CC2-only feature vs CC1. Tom's: "runs a full calibration … during the device self-check. The machine also runs through an optional leveling calibration before each print"[64]Not documented
Filament Handling & Detection
Filament runout sensor (type, location)Two-layer detection. (a) Toolhead optical sensor on the filament-detector board — [filament_switch_sensor filament_sensor] switch_pin=!toolhead:PB1, pause_on_runout=true, event_delay=10.0. A spring-loaded lever blocks an optical gate when filament is present. (b) Per-channel mechanical switches inside CANVAS, one detector board per channel, actuated by a spring-loaded bullet pin. Runout triggers a full flush macro and M2202 gcode_action_report=2505[25][26]Not documented
Tangle/snag detection (exact mechanism, if any — do not accept marketing wording at face value)Real hardware, not marketing. [tangling_switch_sensor] switch_pin=!toolhead:PA1. Physically: a rear-facing Hall-effect sensor at the top of the toolhead filament-detector board; a spring-loaded metal tab in the filament multiplexer extends when filament tension exceeds the spring force (the pneumatic-fitting hub compresses downward), triggering the sensor and raising a tangle error. Prevention side: CANVAS spool holders have a spring-loaded ratcheting rewind mechanism that takes up slack during unload[26][25]Not documented
Clog detection (mechanism, if any)Real: a filament-motion encoder. [z_filament_motion_sensor encoder_sensor] with extruder=extruder, detection_length=50 mm, switch_pin=PB4 (enable), motion_pin=PB3 (odometer), pause_on_runout=true. Mainboard pinout labels these S-DET PB4 = Filament motion detection and M-DET PB3 = Filament presence/absence. Elegoo lists Clog Detection: Yes for CC2, "–" for CC1 — this is a CC2-only feature[1]Not documented
Filament change support (M600 / UI-driven)M600 is the pause g-code (machine_pause_gcode: M600). Multi-colour changes use Elegoo's own M6211 command (M6211 T[next_extruder] L[flush_length] M{old_filament_e_feedrate} N{new_filament_e_feedrate} Q[old_filament_temp] R[nozzle_temperature_range_high] S[new_filament_temp]), plus T[n] tool selects. On-screen load/unload is fully UI-driven[65]Not documented
Spool holder location & max spool size; drybox compatibilityFour spool holders bolt to the right-hand vertical extrusions (two tapped holes each), spools hang outside the enclosure, exposed to ambient air. Inner diameter 53–58 mm; larger spools need a printed adapter. Holders are spring-loaded with a ratcheting rewind. No drybox and no drying function anywhere in the product[26]Not documented
Multi-material/multi-color capability or official upgrade pathNative: CANVAS, 4 colours, single nozzle. Firmware [canvas_dev] on /dev/ttyS1 @115200 with canvas_ctrl_pin=host:PD21; slicer support_mms: 1. The module is separable and also retrofits the CC1 ($55 CC1 version; $120–150 CC2/Centauri 2 version). No chaining/expansion beyond 4 channels[26]Not documented
Cooling & Air Handling
Part-cooling fan(s): count, size, ducting designOne toolhead part-cooling fan: a custom 5020 radial blower with an integrated injection-moulded duct, P/N EFC-05D24D, Shenzhen Hua Xinrong, 0.50 A @ 24 V, 12 000 rpm, 4-pin (tach + PWM). Firmware [fan] pin=toolhead:PA8, tachometer_pin=toolhead:PB15, tachometer_ppr=2, tachometer_poll_interval=0.001[25]Not documented
Auxiliary part-cooling fan?Yes — a custom 12032 radial aux fan on the left chamber panel, P/N EFC-12J24H, 0.8 A @ 24 V, 4-pin (tach + PWM), VHB-taped to the wall with an integrated moulded duct. Firmware [fan_generic fan1] pin=PD15, tachometer_pin=PD14; addressed as M106 P2. Slicer sets auxiliary_fan: 1[66]Not documented
Heatbreak/hotend fan3010 axial fan, 3-pin with tachometer, 0.10 A @ 24 V, 12 000 rpm. Firmware [heater_fan heatbreak_cooling_fan] heater=extruder, pin=toolhead:PB13, tachometer_pin=toolhead:PB14, fan_speed=1. (always full when the extruder is on)[25]Not documented
Chamber/exhaust fan & filtration (activated carbon / HEPA)Yes, and it is the CC2's headline thermal feature. A 12025 axial exhaust fan (P/N EFC12E24W, 0.5 A @ 24 V, 4-pin tach+PWM) works with a servo-driven shutter ("Smart Grille") that switches between exhaust-to-room and internal recirculation-through-filter. Filter media: HEPA + coconut-shell activated carbon ("designed to remove ultrafine particles, VOCs, and odors"), replaceable, $24.99 for 3. Firmware: [cavity_fan] pin=PD17, tachometer_pin=PD16 with a 5-step thermostat (T0=30, T1=38, T2=37, T3=40, T4=45 °C ↔ speeds A=1, B=0.7, C=0.3, D=1, E=0.3, F=0.4, G=0.5); [servo printer_servo] servo_pin=PB7, servo_det_pin=PB2, 1–2 ms pulse, maximum_servo_angle=180, initial_angle=90, M2801_open_angle=45 / M2801_open_time=10 ms, M2801_close_angle=45 / M2801_close_time=400 ms; a limit switch confirms grille position. Addressed as M106 P3[66][67]Not documented
Electronics bay coolingDedicated mainboard fan under stepper/heater-triggered control. [controller_fan board_cooling_fan] pin=PG15, tachometer_pin=PB9, stepper=stepper_x,stepper_y,stepper_z,extruder, heater=extruder,heater_bed, fan_speed=1.0, idle_speed=0.0, idle_timeout=30[1]Not documented
Fan control (PWM? RPM feedback? firmware evidence)All five fans are PWM-controlled, and four of the five have tachometer feedback wired and polled in firmware: part-cooling (toolhead:PB15, ppr=2, poll 1 ms), heatbreak (toolhead:PB14, poll 1 ms), board fan (PB9), cavity/exhaust (PD16), aux (PD14). Elegoo markets a "Fan Self-Check" feature; the connectors are documented as "tach + 5 V PWM"[1]Not documented
Electronics & Power
Mainboard model & MCU (exact chip markings if teardowns exist)Elegoo "self-developed" mainboard, part number EF-M5-V1.0.073. Main SoC: Allwinner R528-S3, which *also* runs the motion MCU firmware on its internal HiFi4 DSP core — the shipping config's [mcu] is serial=/dev/rpmsg_ctrl-dsp_rproc@0 with restart_method=remoterpc, i.e. rpmsg to an on-die DSP, not an external microcontroller. Two auxiliary MCUs: toolhead = GD32 (firmware build target toolhead_gd32, version string toolhead_gd32-00.00.00.03-app), bed = STM32F402RCT6. CANVAS mainboard = GD32F303RCT6[1][45][27]Not documented
Host computer (SoC, RAM, storage) if firmware runs on embedded LinuxAllwinner R528-S3, 32-bit ARM (arch/arm, sun8iw20p1 platform, SMP, VFP+NEON), 128 MB in-package DRAM, 8 GB eMMC. Linux 5.4.61 (Allwinner BSP). Rootfs uses opkg (OpenWrt-style ipk packaging) with app data under /opt (/opt/inst, /opt/usr/cfg, /opt/usr/gcode)[1][68]Not documented
PSU (brand, wattage, rail voltage)Partially known. Logic/motor rail is 24 V DC (Elegoo spec "Power Output: 24 V"; mainboard input is a 2-pin barrier terminal marked +24 V/GND with 9.6 mm pitch). The bed does not use the 24 V rail at all — it is switched mains via an SSR board. PSU brand, model and 24 V wattage are[1][45]Not documented
Input voltage (110/220 V, switch or auto)AC 100–240 V, 50/60 Hz — auto-ranging, no voltage switch documented[69]100-132 V / 15 A or 200-240 V / 7 A, 50/60 Hz[3]
Total rated power draw1100 W @ 220 V; 350 W @ 110 V (rated, not measured)[55]Not documented
Expansion headers / spare ports (fans, steppers, GPIO, USB host)Unusually well documented. Mainboard carries: 2×4 pin header = DSP UART + UART0 serial consoles (5 V/TX/RX/GND each); a FEL 4-pin header (GND/DP/DM/5 V) for Allwinner recovery; a front USB-A host port; a camera 4-pin USB; the CANVAS "AMS port" (2×2 Micro-Fit 3.0, RS485-A/B + 24 V + GND); Bed MCU RS-232 (5-pin, 5 V switched for reset); JST-XHB connectors for chamber temp (PH0), light (PB5), FAN-1 (PD14/PD15), BOX-F (PD16/PD17), exhaust servo (PB2/PB7 + limit switch), Z-endstop (PB10), bed heater PWM (PG13), bed temp (PB14), mainboard fan; and an onboard piezo buzzer (PB12). Toolhead link is a USB-C connector carrying 24 V on Vbus[1][25]Not documented
Firmware & Openness
Firmware base & current version (Klipper fork / Marlin fork / proprietary)"ELEGOO OS" = a closed C++ re-implementation of Klipper. The released source tree is unmistakably Klipper: src/ + lib/ with the full Klipper MCU HAL set (stm32, rp2040, atsam, avr, ar100, linux, simulator, lib/kconfiglib), and elegoo/ containing printer.cpp, configfile.cpp, chelper/, kinematics/, extras/ (215 files) — the Klippy host transpiled from Python to C++. Config syntax is Klipper's ([stepper_x], [tmc2209 …], [input_shaper], [bed_mesh], rotation_distance, pressure_advance). Slicer declares gcode_flavor: klipper. Community binary analysis pins the base at Klipper commit 28f60f7e, 616 commits past v0.9.1 — ⚠ this specific commit identification is a CC1 finding: freethecode.lol is a Centauri Carbon (CC1) campaign page and mentions the CC2 zero times (verified by full-text search, 2026-08-21). It is quoted here as the platform lineage, not as a CC2-specific binary analysis; nobody has published a commit-level diff of a CC2 binary. Latest OTA catalogued: v02.00.02.00 (2026-05-28); the published source corresponds to ~v01.01.13.10 / release 2602101855[70][71][15]Proprietary Stratasys firmware; print preparation is GrabCAD Print. The F370 additionally carries an Insight software licence and DoD STIG compliance powered by Red Hat Enterprise Linux[3]
Source code availability (repos, GPL compliance status, last update date)A GPL-3.0 source repo exists but is stale and incomplete, and compliance is actively disputed. elegooofficial/CentauriCarbon2 was created 2026-03-11, last pushed 2026-03-12, and has never been updated — while at least three OTA firmware releases have shipped since (v01.03.02.36, v01.03.02.51, v02.00.02.00). Open issue #8 "Out of compliance with GPLv3" (2026-06-02) is still open, with 8 comments escalating through 2026-08-14 — including an @-mention of @realrossmanngroup on 2026-08-13 and, on 2026-08-14, the first reply from an ELEGOO account (anjis-elegoo), which quotes the complaint back but does not commit to a source-release date. Re-verified 2026-08-21: still open, no new source push. Open issue #1 shows the release cannot even be built: mcu_build.sh -b toolhead_gd32 fails with can't found configfile: CentauriCarbon2/mcu_config/toolhead_gd32.config — the directory is missing from the repo. The same "Out of compliance with GPLv3" issue is open on the CC1 repo (#26). The freethecode.lol campaign is still live and still marked "Still ongoing" (issue raised 2025-08-07)[70][72][73][74][71][75][15]Not documented
Root/SSH access: possible? official or community methodAnd this is the answer that changed in mid-2026. An SSH daemon was present in CC2 firmware up to and including v01.03.02.51 (2026-05-09). Firmware v02.00.02.00, released 2026-05-28, "removes the SSH process entirely" and simultaneously blocks downgrades to any earlier version. OpenCentauri publishes a repacked v01.03.02.51 specifically to defeat the downgrade block ("Use at your own risk"). No CC2 community firmware currently restores SSH: OpenCentauri Patched Firmware is explicitly "Not currently" compatible with the CC2 (it is built on CC1 1.1.40), and COSMOS's public FAQ still says CC2 support is a "Maybe". Hardware-level root remains available via Allwinner FEL mode + UART (documented for the CC2 specifically, eMMC on mmc dev 1)[15][76][77][78][79]Not documented
Moonraker / Mainsail / Fluidd or other open API available (stock vs after mods)?None of them, stock. The host is a single C++ binary with a proprietary IPC socket (-a /tmp/elegoo_uds) and an embedded Mongoose 7.12 web server. What *does* exist: a built-in WebUI, an MJPEG camera stream on port 3031 (:3031/video), an Elegoo SDCP protocol used by ElegooSlicer/the Matrix app, an MQTT transport (the non-shipping config even hard-codes broker_address=tcp://broker.emqx.io:1883), and OctoEverywhere / Home Assistant integrations built on the SDCP API. OpenCentauri has reverse-engineered and documented the API and MQTT surface[80][81][82][71]Not documented
Notable community firmware/mods (names, repos, what they add)For the CC2 specifically: none usable today. The ecosystem is real but CC1-first. (a) OpenCentauri Patched Firmware (repo OpenCentauri/cc-fw-tools) — adds SSH root, opkg/entware, boot logo, homing-position change, mid-print WebUI edits, USB-Ethernet support, M8212/M8213 chamber-light g-codes and TEMPERATURE_WAIT SENSOR=box; CC1 only. (b) COSMOS (OpenCentauri/cosmos, 231 stars) — full Klipper/Kalico on stock hardware via Yocto; "Add support for CC2" was merged 2026-07-01 (PR #225, author's own note: *"Untested, will still need some work probably"*), release 26.07.0 shipped 2026-07-29, yet the public FAQ still says CC2 is a "Maybe". (c) OpenCentauri/cad — full CC2 CAD models and FDM-optimised replacement parts. (d) Elegoo-Tag-Library — dumps of Elegoo RFID tags. (e) An OpenCentauri drop-in replacement mainboard project is in progress[83][84][85][86][87][88][89][77]Not documented
Firmware update mechanism (OTA/USB) & update cadence historyOTA over Wi-Fi, or offline via USB. Packages are.zip.sig — a signed/encrypted wrapper containing *.swu.sig (the swupdate payload) and *.json.sig (metadata). The device uses an A/B partition scheme managed by swupdate: the update is written to the inactive slot which becomes primary on next boot. USB path: drop the.zip.sig on a FAT32 stick → Settings → Check for Updates → Offline Update. Cadence: 7 releases in ~7 months (2025-10-31, 2025-11-17, 2025-12-11, 2026-01-09, 2026-04-09, 2026-05-09, 2026-05-28)[15]Not documented
G-code flavor & notable custom G-codes/macrosKlipper flavour (gcode_flavor: klipper) plus a substantial proprietary extension set: G180 S<n> — a numbered macro dispatch table (S1–S10 calibration steps, S800 "move to waste box", S810–S813 flush/cutter steps, S900-series mesh profile logic); M6211 — CANVAS tool change with flush length, feedrates and temperatures; M2202 gcode_action_report=<code> — UI progress reporting; M2801 — exhaust-grille servo open/close; M190 S<t> A — bed heat with an extra A flag; SET_CONDITION J/A/B … SET_CONDITION_END — a conditional-execution primitive not present in mainline Klipper; plus standard BED_MESH_CALIBRATE, SAVE_CONFIG, SET_PRINT_STATS_INFO, PROBE, SET_KINEMATIC_POSITION, TEMPERATURE_WAIT. OpenCentauri maintains a custom-g-code reference[90]Not documented
Root shell: exact method (official setting toggle / vendor-documented / community exploit / none). Is root persistent across OTA firmware updates, or wiped each update?Three tiers, none of them a supported toggle. (1) No official/vendor-documented root method exists — there is no developer-mode switch in the UI and no Elegoo documentation of shell access. (2) Firmware-resident SSH existed up to v01.03.02.51 (2026-05-09) and was deleted in v02.00.02.00 (2026-05-28); OpenCentauri describe the change as removing "the SSH process entirely, making it more difficult to perform research on a live device", and the same release blocks downgrades. Staying on ≤v01.03.02.51, or flashing OpenCentauri's repacked v01.03.02.51, is therefore the only firmware-level route — and I could not find published CC2 root credentials (the widely-quoted root / OpenCentauri pair belongs to OpenCentauri's CC1 patched firmware, which does not run on a CC2). (3) Hardware-level root is confirmed available: Allwinner FEL mode (short R53 while resetting, or efex from U-Boot) plus the on-board UART0/DSP serial headers, with CC2-specific artefacts published (u-boot-sunxi-with-spl-cc2.bin, backup_cc2.scr/restore_cc2.scr, eMMC on mmc dev 1) — this gives full eMMC read/write, i.e. offline root. Persistence: an OTA update replaces the entire rootfs slot (A/B swupdate), so any rootfs modification is wiped by the next official update.[15][76][78][91][79][1]Not documented
Userland: OS base (Debian/Ubuntu/Buildroot/OpenWrt/busybox-only), package manager present (`apt`/`opkg`/`ipkg`/none), CPU architecture (armv7 / aarch64 / mips / x86), and free space on the writable partition. A busybox/no-apt rootfs with a few MB free is a red flag — say so.OS base: a Buildroot/OpenWrt-style embedded Linux, not Debian/Ubuntu. Evidence: opkg is the package manager (Elegoo's own build docs: "开发板上opkg常用指令 … opkg install xxx.ipk", -o /opt/packages/), packaging is ipk with control.tar.gz/data.tar.gz and debian-binary = 2.0, init is /etc/init.d-style shell scripts, and app state lives under /opt (/opt/inst, /opt/usr/cfg, /opt/usr/gcode). Kernel: Linux 5.4.61 (Allwinner BSP). Architecture: 32-bit ARM (armv7-class), arch/arm, platform sun8iw20p1, SMP, VFP+NEON — *not* aarch64. RAM: 128 MB total, in-package. Storage: 8 GB eMMC. Free space on the writable partition: for the CC2 — the CC1-derived partition map gives rootfsA/B ≈ 134 MB each, rootfs_data ≈ 134 MB, UDISK ≈ 7.06 GB, but I did not find a CC2 partition dump[68][1][92]Not documented
Native Tailscale feasibility: can `tailscaled` run persistently on-device? Cite concrete evidence — community guides, wiki entries, forum posts, or repos of people actually doing it on THIS model. Note whether it needs `/dev/net/tun` (kernel TUN support) and whether the kernel provides it, plus whether userspace-networking mode is the only option. Distinguish "someone did it" from "should theoretically work."Not demonstrated by anyone, and structurally hostile. (a) No evidence any person has run tailscaled on a Centauri Carbon of either generation — I searched OpenCentauri's docs, its 4 relevant GitHub orgs/repos' issues, freethecode.lol, and the open web for "Tailscale + Centauri Carbon"; the only 3D-printer Tailscale guidance found is generic (Voron/Raspberry-Pi subnet-router patterns). (b) /dev/net/tun is very likely absent: CONFIG_TUN is not set in either Allwinner R528/T113 defconfig in OpenCentauri's fork of the vendor kernel (sun8iw20p1smp_defconfig, sun8iw20p1smp_t113_auto_defconfig); the only tunnel symbol present is CONFIG_IPV6_TUNNEL=y, and no CONFIG_NETFILTER* symbols are set at all. Without TUN, tailscaled must run --tun=userspace-networking, which rules out subnet-router and exit-node roles and costs throughput. (c) 128 MB RAM shared with the motion controller is a hard practical ceiling — tailscaled's resident set is a large fraction of that. (d) On current firmware there is no shell to install it from (N8), no apt, and an A/B rootfs that erases changes on update (N12)[93][1][77][83]Not documented
SSH daemon: present by default or must be installed/enabled? Default credentials if documented. Does an OTA update disable it or reset the password?Present by default up to v01.03.02.51; absent from v02.00.02.00 onward. OpenCentauri's wording is that v02.00.02.00 "removes the SSH process entirely", i.e. the daemon shipped enabled (or at least resident) in earlier builds. Default credentials for stock CC2 firmware: — I found none published. The frequently-cited root / OpenCentauri pair is explicitly the credential set for OpenCentauri's patched CC1 firmware, which does not support the CC2. An OTA update to v02.00.02.00 removes SSH and blocks rollback, so an OTA can and does permanently disable it[15][83][76]Not documented
Filesystem persistence: is the rootfs read-only or overlay-mounted? Do user-installed binaries and init/systemd services survive reboot and survive firmware updates? Is there a supported place to persist customizations?A/B rootfs managed by swupdate; user-installed software does not survive official updates. Each update is written to the *inactive* rootfs slot, which then becomes primary — so anything added to the live rootfs is left behind on the now-inactive slot. There is a separate rootfs_data partition (overlay/persistent data) and a large UDISK partition; Elegoo's own supported persistence locations are /opt/usr/cfg (user config, incl. autosave.cfg written by SAVE_CONFIG) and /opt/usr/gcode (job storage), with defaults in /opt/inst. run_printer.sh even contains a commented-out "copy default config to user config" path, showing Elegoo intended /opt/usr/cfg/user_printer_dsp.cfg as a user-override slot — but it is commented out in the shipped script, so the binary is launched against /opt/inst/printer_dsp.cfg and user config overrides are not active[15][92]Not documented
Connectivity, UI & Camera
Display: size, type, touch?5.0-inch colour capacitive touchscreen, front-mounted, connected by FFC ribbon (RGB888 + touch). Controller is a Sitronix ST77922 panel with an ST1633i I²C capacitive touch controller[94][1][95][96]Not documented
On-device UI capabilities (model preview, per-object controls, etc.)Model preview and file browse (local + USB), one-click calibration suite, per-spool CANVAS load/unload with manual filament type/colour entry, RFID tap-to-read, camera live view + timelapse, chamber light toggle, Z-offset adjust, network/IP display, offline firmware update, print history. v01.03.02.51 added "the ability to exclude and reset regions containing foreign objects" (a foreign-object exclusion feature). Per-object cancellation ("skip object") is NOT supported — it is an open feature request[15][97]Not documented
WiFi (band/standard), Ethernet, USB ports, SD/flash-driveWi-Fi (2.4 GHz-class AIC8800D80 SDIO module) + USB flash drive only. NO Ethernet port. No SD card slot. Hardware: a front USB-A host port and a separate 4-pin camera USB header on the mainboard[1][98]Wired TCP/IP at 100 Mbps minimum, 100base-T Ethernet, RJ45. Wireless-ready IEEE 802.11 n/g/b with WPA2-PSK or 802.1x EAP, CCMP/TKIP encryption[3]
Cloud service & phone app; LAN-only mode possible?Cloud: Nexprint (Elegoo's model hub, integrated into ElegooSlicer's home screen, in beta) and the ELEGOO Matrix mobile app (binding added in v01.03.01.89, app ≥ v1.0.11). LAN-only mode exists and works: connect to Wi-Fi, note the displayed IP, add the printer in ElegooSlicer's Device tab on the same subnet. However, LAN-exclusive mode is mutually exclusive with useful features[15][99]Not documented
Camera: built-in / optional? Resolution & framerate (verify — marketing often omits real fps)Built-in and standard. 1280 × 720 (720p), 16:9, max 30 Hz, fixed focus (glued barrel), auto exposure, FOV ~90–110°, USB 2.0, 30 × 30 mm PCB, 500 mA @ 5 V, 4-pin JST-ZH 1.5 mm connector, enumerates as "Integrated Camera". Stream is MJPEG on port 3031 (:3031/video)[100][82]Not documented
Camera features: live monitor, timelapse, AI failure detection (spaghetti detection) — how real is it?All three present. Live view in the WebUI/Matrix app/ElegooSlicer; timelapse with video export (a v02.00.02.00 changelog entry fixes "mismatch between timelapse video filenames and print file filenames during export"); AI spaghetti/failure detection with notifications. Real-world reliability is mediocre[101][15]Not documented
LED chamber/toolhead lightingChamber LED present and firmware-controlled: [output_pin led_pin] pin=PB5, value=0; mainboard "Light" connector is a JST-XHB-3P with +24 V (max 1 A), GND and signal on PB5. Toolhead has an LED PWM pin that is not connected[1][25]Not documented
Calibration Routines & QoL
One-touch auto-calibration suite: what exactly does it calibrate?Elegoo "Full-Auto Calibration". Verified contents: (a) 121-point bed mesh, (b) Auto Z-offset via load-cell nozzle touch, (c) input-shaping / vibration compensation, (d) an automated nozzle-clean cycle that precedes probing, (e) nozzle-temperature Z-compensation table, (f) sensor self-checks (fan, exhaust grille, cutter status, CANVAS). Notebookcheck timed the whole thing at 26–27 minutes; CreativeBloq at "around ten minutes" and notes "it gets somewhat noisy"[101][102]Not documented
PID autotune exposed to user?Yes — there is a dedicated [pid_calibrate] section with its own preparation macro (pid_calibrate_gcode=G90\nG28 X Y TRY\nM204 S10000\nG180 S800\nM400\n, i.e. home and park at the waste station before tuning). Factory PID values are shipped for both heaters: extruder pid_kp=25.989 / ki=3.397 / kd=49.705; bed pid_Kp=46.504839 / Ki=1.453276 / Kd=372.038710[103]Not documented
Flow-rate calibration toolingAs an on-printer feature. No flow-calibration macro exists in [g180] or elsewhere in the config. The practical path is ElegooSlicer's inherited OrcaSlicer calibration suite (flow ratio, PA, temperature towers), since ElegooSlicer is an OrcaSlicer/BambuStudio fork. Vendor per-material flow ratios are shipped (e.g. PAHT-CF filament_flow_ratio: 0.96)[104]Not documented
Belt tension check/indicatorsNone. No belt-tension routine, indicator, or resonance-based tension readout in firmware; no tensioning procedure in the manual. Hardware provides spring-loaded automatic tensioners instead (BOM X/Y轴同步带张紧弹簧 = XY belt tensioning springs, XY轴皮带张紧惰轮支架 = tensioner idler brackets)[105]Not documented
First-layer inspection featuresYes — scan_first_layer: 1 is set in the machine profile, i.e. camera-based first-layer inspection is enabled. Separately, an elaborate automated nozzle-clean-and-verify routine runs before probing (clean_nozzle_gcode / [g180] S1–S2: heat to 200 °C, wipe on the silicone wiper, cool to 140 °C, run a Z-touch pattern, re-wipe)[106]Not documented
Skew calibrationNone. No [skew_correction] section in either config, no skew routine in [g180], nothing in the manual or any review[107]Not documented
Assembly level & time from unbox to first printSemi-assembled; ~15–20 minutes of assembly, ~45 minutes unbox-to-first-print including calibration. Steps: remove 3 bed transport screws, clip on the touchscreen (ribbon cable), screw on the nozzle-wiper assembly and waste chute (4 screws, from inside, at the rear), bolt the CANVAS bracket + module (3 screws), plug the CANVAS power/signal cable, route 4 Bowden tubes to the toolhead hub (2 screws), bolt 4 spool-holder brackets (2 screws each), fit the tophat + CANVAS extension[108][39]Not documented
Power-Loss & Interruption Recovery
Power-loss recovery: mechanism (how is state saved? capacitor / eeprom / file on shutdown?)Real hardware-sensed power-loss detection with an energy-reserve circuit, not a periodic-file-write hack. [por] (power-outage recovery): sensor_pin=host:PG9 (mains-loss sense), ctrl_pin=host:PG11, charge_pin=host:PD20, charge_time=30.0 (a reservoir/supercap charge line), rest_time=0.01 (10 ms poll), and an explicit shutdown_pins list that de-energises everything in a defined order on detection: host:PD22 (LCD PWM), host:PE17 (nozzle power), host:PB11 (bed power), PG13 (bed control), !PF6/!PE15/!PE12 (X/Y/Z enables), PB5 (light), PD17/PD19 (box fan), PD15 (fan1), PG15 (mainboard fan). Enabled at the print layer via [virtual_sdcard] power_outage_enable=1[109]Not documented
Verified working? Third-party test results; resume seam qualityConfirmed working by an independent reviewer, but with documented bugs that took two firmware releases to fix. Notebookcheck: "the auto-filament refill, filament runout sensor, hotend cover sensor, and power loss recovery … worked as they should." Firmware history shows real defects: v01.03.02.51 (2026-05-09) fixed "print history showed a total print time of 0 after resuming printing following a power outage", and v02.00.02.00 (2026-05-28) fixed "resume printing failed after power loss when using an external spool under certain conditions". v01.03.02.36 "Optimized print recovery quality after pause/resume". No reviewer photographed or measured the resume seam[101][15]Not documented
Filament-runout pause/resume behaviorAutomatic and elaborate. On runout the printer runs a full macro: M400 → G28 X Y TRY → M204 S10000 → park at the waste station (G180 S800) → part fan to 25 % → purge E10 F300 + E5 F150 → fan to 88 % (M106 S225) → 5 s dwell → three-stage flush/wipe (G180 S811 → S810 → S800) → fans off → report M2202 gcode_action_report=2505 to the UI. Governed by pause_on_runout=true, event_delay=10.0, pause_delay=1.0. In CANVAS mode, auto-refill from a duplicate spool takes over instead of pausing. Pause/resume additionally has a scripted purge-and-prime on resume[2][15]Not documented
Materials Support
Officially supported filament listElegoo's own two-tier list: "Ideal: PLA / PETG / ABS / ASA. Capable: TPU³ / PC / PA / PET / fiber-reinforced filaments⁴." The shipped slicer carries 30 CC2-specific filament profiles: PLA (Basic, PRO, +, Matte, Silk, Galaxy, Glow, Marble, Sparkle, Translucent, Wood, Rapid PLA+), PLA-CF, PETG (+ PRO, HF, Translucent, Rapid), PETG-CF, PETG-GF, PET-CF, ABS, ASA, ASA-CF, PC, PC-FR, PAHT-CF, TPU 95A, Rapid TPU 95A[110]PLA, ABS-ESD7, ABS-M30, ASA, Diran 410MF072, FDM TPU 92A, PC-ABS, ABS-CF10, with QSR soluble support. Diran and PLA use breakaway rather than soluble support[3]
PLA/PETG/TPU results & constraints (min TPU shore hardness)PLA and PETG: excellent and effortless — the unanimous reviewer verdict. Vendor profiles: PLA 210 °C / 21 mm³/s; PETG 250 °C / 11 mm³/s. TPU: works down to 95A, verified by Tom's ("The system worked great for every filament I printed with, including TPU down to 95A shore hardness"; a TPU Air Duster at 0.12 mm / 50 mm/s took "just over two hours … surface finish is a little rough, but the print is fully functional"). TPU constraint on the Combo: you must fit the Flexible Filament Adapter and physically disconnect the CANVAS cable — i.e. no multicolour TPU. Profiles: TPU 95A 3.2 mm³/s, PA 0.1[111]Not documented
ABS/ASA feasibility (enclosure/chamber constraints, warping reports)Demonstrated on a US 110 V machine: a full standard-ABS print succeeded with no warping and no layer cracking. Aurora Tech printed standard ABS in a 17 C garage with the tall cover fitted; the job ran 3 h 41 min (about 18 % over the slicer estimate) and he reports "no corner warping", the part "sticks very well because the ambient temperature is stable", "no layer cracking", overhangs "printed nicely using standard ABS" and a good bottom surface, with the chamber holding ~45 C and peaking ~47 C (B6). Enclosure plus 110 C bed plus Smart Grille recirculation also give a "temperature hold mode where the vents shut off" for ASA (Notebookcheck). Vendor profiles: ABS 270 C / 18 mm3/s / fan capped at 40 %; ASA 270 C. Remaining caveats: (a) ASA is weaker than ABS here. Notebookcheck hit ASA adhesion problems, fixed them only by preheating the bed 10 minutes at 110 C, and photographed warping on an ASA test print; (b) there is no active chamber heating and no chamber preheat/wait, and an owner reports the CC2 starts printing before a requested 45-50 C chamber target is reached; (c) the ABS success is a single reviewer on a single part geometry. [RETRACTED after critique: an earlier draft claimed the bed mesh is probed at a fixed 60 C rather than at ABS bed temperature. It is not; the start g-code waits for print bed temperature (M190... A) before BED_MESH_CALIBRATE. See J6.][20][112][21][77]Not documented
PC / Nylon / CF-filled feasibility (nozzle & extruder wear constraints)Demonstrated on real parts by Tom's Hardware, and this is the CC2's strongest surprise. PC: 7 utility knives in Prusa PC Blend, 0.2 mm, 100 mm/s, 6 h 06 min — "the prints were completed … and are perfect"; plus replacement spool holders in Polymax PC, 5 walls, 2 h 36 min. PA (nylon): Bambu Lab PAHT-CF RC part, 0.2 mm, 100 mm/s, 2 h 12 min — "Though this print can be a warping nightmare, it did really well". Tom's summary: "surprisingly strong with engineering materials, even without an actively heated chamber". Vendor profiles: PC 270 °C / bed 100 °C / 16 mm³/s / fan 35 % max; PAHT-CF 290 °C / bed 100 °C / 6 mm³/s / fan 30 %. Second independent confirmation (added 2026-08-19, reader-supplied): Aurora Tech, on a US 110 V unit, printed PA-CF successfully with the enclosure at ~41 C near the end of a 54-minute job, describing the surface as "as good as completely dried PACF" and the part as so stiff that "when I drop it on the table, it sounds like metal rather than plastic", despite the spool having been left open about two weeks; he also printed PPS-CF at the maximum nozzle temperature and reports it "worked very well" max, first 3 layers fan-off, flow ratio 0.96; PET-CF 270 °C / 8 mm³/s; PLA-CF 16 mm³/s with required_nozzle_HRC: 40. Abrasion is handled by the stock hardened-steel-tipped nozzle and SDK11 tool-steel hobbed gears; https://www.youtube.com/watch?v=xp-jQ7dljV0 at 21:20-22:10 and 26:20 (Aurora Tech; evidence/auroratech_cc2_combo_transcript.md)[25]Not documented
Effective material ceiling given hotend+bed+chamber limits (reasoned, cite limits)Ceiling ≈ PC / PA(-CF) / PET-CF — i.e. everything the 350 °C nozzle and 110 °C bed can reach *that does not require a heated chamber*. Reasoning from the verified limits: nozzle firmware max 365 °C (claim 350) is enough for PC (270), PAHT-CF (290) and PET-CF (270) with margin, and would nominally reach PPS/PPA-class temperatures; bed firmware max 125 °C (claim 110, ot_bed=130) covers PC/PA bed requirements (vendor profiles use 100 °C); the binding constraint is the chamber — passive only, thermostat setpoints imply 30–45 °C, ot_box=100, no heater, no preheat-and-wait. That rules out reliable large ABS/ASA/PC-CF/PPS parts and warp-sensitive geometry, which is precisely where 50–60 °C active chambers earn their keep. Practically: excellent to PETG/PLA-CF; very good for small-to-medium PC and PA-CF; marginal for large ABS/ASA; not a PPS/PEEK machine despite the nozzle number — notwithstanding Elegoo's own non-Combo comparison table, which lists "Capable: PPS/PPS-CF/PPS-GF, PPA-CF/PPA-GF" (see R1); that claim is rejected here on the chamber argument and no reviewer has printed PPS on either Centauri[21]Not documented
Filament profile ecosystem in the recommended slicerStrong and CC2-specific. ElegooSlicer (an OrcaSlicer/BambuStudio fork, distributed on the included USB and on GitHub) ships 30 filament, 21 process (0.08–0.48 mm layers across 0.2/0.4/0.6/0.8 nozzles) and 5 machine profiles named specifically for the CC2 (@ECC2 / @Elegoo CC2). Per-material pressure advance, flow caps, fan curves, plate temperatures and exhaust-fan logic are all pre-set. OrcaSlicer and Cura are also listed as supported. RFID auto-selects the profile for Elegoo-branded spools[113]Not documented
Safety
Thermal runaway protection (verify in firmware source if at all possible)Present and firmware-verified for both heaters. [verify_heater heater_bed]: max_error=60, check_gain_time=60, hysteresis=5, heating_gain=2. [verify_heater extruder]: max_error=30, check_gain_time=20, hysteresis=5, heating_gain=2. These are Klipper's standard runaway semantics (heater must gain ≥2 °C per check_gain_time while heating; cumulative error beyond max_error faults the printer). Backed by independent hardware cutoffs: ot_bed=130 and ot_box=100, and a thermal fuse in the mains bed circuit[45]Not documented
Certifications (UL/ETL/CE/FCC — verify, don't assume)I could not verify a single certification for the CC2. The printed manual contains no FCC/CE/UKCA/RoHS/WEEE statement and no declaration of conformity; the Elegoo product page lists none; the packaging/nameplate was not available to me[114]CE (low-voltage and EMC directives), FCC, EAC, cTUVus, KC, RoHS, WEEE, REACH, RCM[3]
Hardware safety: fusing, strain reliefs, belt covers, pinch pointsPartly documented. Bed circuit: mains AC with ground present and a thermal fuse, switched by an SSR board. OpenCentauri's own warning is unambiguous: "Danger: The Bed runs on mains AC current at 110/220 V. These voltages may be lethal. Exercise extreme caution around the bed and SSR board." Enclosure with glass door and tophat covers all belts and the gantry. Manual safety notes cover burns, pinch hazards, grounding, dust maintenance and adult supervision of children. Mainboard 24 V input is a 2-pin barrier terminal described as "very flimsy — do not overtighten." Toolhead USB-C carries 24 V on Vbus (fries anything else plugged in). No fuse ratings or strain-relief details are published[45][1]Not documented
Firmware safety limits (max temp cutoffs — exact values)Nozzle max_temp=365 / min_temp=-100; bed max_temp=125 / min_temp=-100, ot_bed=130; chamber max_temp=110 / min_temp=-100, ot_box=100. Idle timeouts: extruder 300 s (extruder_timeout_gcode=M104 S0), bed 600 s (range 60–259 200 s). Probe force limits: trigger_force=200 g, safety_limit=1200 g. min_extrude_temp=-100 — cold-extrusion protection is DISABLED, as is Klipper's extrusion cross-section check (max_extrude_cross_section=9999999)[115]Not documented
Known safety incidents / recalls / fire reports (with sources)None found for the CC2. No recall, fire report or safety incident surfaced in any of the eight reviews, the Elegoo GitHub issue trackers (CC2 repo: 11 issues, none safety-related), the OpenCentauri issue trackers, freethecode.lol, or general web search[116][117][71]Not documented
Noise & Power Consumption
Noise: claimed dB and independently measured dB (distance/method)Claimed ≤45 dB (footnoted "Data from Elegoo Lab. Tested with Elegoo PLA filament in Silent Mode with the auxiliary part cooling fan turned off"). Independently measured by Notebookcheck: average 44–47 dB, peaks to 54 dB. Distance and instrument not stated[12]46 dB maximum during build, 35 dB idle — manufacturer specification, no distance or method stated, and not an independent measurement[3]
Silent/quiet mode available?Yes — Elegoo's own noise footnote references "Silent Mode". Firmware side, the mainboard fan idles at zero (idle_speed=0.0, idle_timeout=30) and the cavity fan is thermostatically staged, both of which reduce idle noise. No dedicated silent-mode section appears in the released config, so the mode is implemented above the motion layer (UI/host)[118]Not documented
Power draw: idle / PLA print / high-temp print (measured preferred)No measured CC2 power figures exist. Rated only: 1100 W @ 220 V; 350 W @ 110 V, 24 V logic rail, ~1000 W of that being the mains bed[119]Not documented
Reliability, Support & Ecosystem
Warranty length & support reputation (evidence, not vibes)12 months standard on the printer, with a component-tiered warranty table: consumables carry no warranty (PEI platform plate, build plate, nozzle kit, PTFE tube, heater, thermistor, hot end, packaging, manual, tools); CANVAS parts have a limited warranty covering the feeder-module motherboard, 4-pin cable, five-way module, spool holder (excluding support claws), feeder motor, communication board, gearbox/cutter assembly, fan and housing, with "damage caused by human error … not covered". A 2-year extended warranty is sold for the Centauri series (e.g. via MatterHackers). Support reputation: mixed, evidence-based[120][71]Not documented
Common failure points (from long-term reviews/forums, with sources)Six documented so far, all from the first ~7 months. (1) Spool holders — Tom's physically broke one and "tore the rubber grips off" with a third-party cardboard spool; TechRadar had Elegoo plastic reels slip off the holder; OpenCentauri documents a ratchet clicking noise needing grease. (2) Toolhead filament-hub collets are effectively unremovable — Tom's could not extract the PTFE tubes even with the supplied tool and help, so clearing an extruder clog means unscrewing the whole hub. (3) 250 °C load routine cannot purge high-temp residue (firmware-confirmed). (4) Software/connectivity flakiness — Notebookcheck: random refusal to connect to ElegooSlicer on Windows, monitoring-window errors, 17 %-optimistic time estimates; GitHub issue #9 LAN-mode exclusivity. (5) False positives on clog/spaghetti and tangle detection (Notebookcheck; firmware v01.01.16.40 changelog). (6) Purge waste volume — 3DwithUS: on a 4-colour Gengar print "the purge waste was considerable though, almost the same amount as the model itself"[108][26][99][15]Not documented
Spare parts availability & pricing (nozzle, hotend, plate, board, belts)Good and CC2-specific, ordered direct from Elegoo US. Verified live prices (2026-08-19): 0.4 mm brass/hardened-steel nozzle kit $22.99; multi-size (0.2/0.4/0.6/0.8) nozzle kit $24.99; dual-sided build plate $22.99 (3-pack $39.99); ceramic heater (CC2) $9.99; thermistor (CC2) $9.99; hotend silicone sock ×3 (CC2) $9.99; composite HEPA+carbon filter ×3 (CC2) $24.99; auxiliary part-cooling fan (CC2) $28.99; 3010 axial fan $12.99; dual extruder gears $14.99; strain gauge $12.99; spool holder (CC2 Combo) $21.99, set of 4 $45.99; spool claws ×3 $10.99; anti-vibration feet ×4 (CC2) $11.99; CANVAS module $150 (with cover) / $120 (without); Accessory Kit for Centauri Series $59.99[11]Not documented
Community size (subreddit size, wiki quality, Discord/Facebook groups)Substantial and unusually technical for a 7-month-old machine. OpenCentauri Discord ~5,800 members; ELEGOO Official Discord ~32,700 members. OpenCentauri org: 26 public repos, cosmos at 231 stars with active development through 2026-08-21, plus a full MkDocs wiki with dedicated CC2 hardware pages (mainboard, toolhead, bed, camera, screen, misc, CANVAS, docs) and a CC2 firmware archive. Elegoo maintains official GitHub repos with public issue trackers for both CC1 (25 issues, numbering to #28 because three numbers are PRs) and CC2 (11 issues, all open). Elegoo also runs official Reddit and Facebook presences[121][122][123][124][125][116]Not documented
Mod/upgrade ecosystemActive but CC1-weighted. CC2-applicable today: full CAD models and FDM-optimised replacement parts (OpenCentauri/cad, 465 MB repo, pushed 2026-07-06, includes a CC2 model per PR #13); printable mods, light mods and camera replacement guides; Elegoo RFID tag dumps (Elegoo-Tag-Library); CANVAS retrofit onto CC1; printable spool holders (Tom's used a Voron-derived design after breaking his). Not yet CC2-ready: OpenCentauri patched firmware (CC1 only), COSMOS (CC2 support merged 2026-07-01 but "untested" and not endorsed in the FAQ), the OpenCentauri replacement mainboard project[123][88][126][127][89]Not documented
Long-term (6–12 month) reliability reportsNone exist yet. The CC2 shipped 2026-01-26, so the oldest retail units are ~7 months old at the access date. The longest documented exposure I found is 3DTechValley's "3 weeks of hands-on testing with a retail unit"; every other review is a launch-window unit tested over days. No 6-month or 12-month follow-up, durability teardown, or MTBF data exists[116][117]Not documented
Independently Measured Performance
Dimensional accuracy measurements (third-party, with numbers)TechRadar, calipers on a 5-step accuracy target — the only real numbers that exist. Target 25 mm → X 24.93 (−0.07), Y 24.85 (−0.15); 20 mm → X 19.97 (−0.03), Y 20.01 (+0.01); 15 mm → X 14.94 (−0.06), Y 14.95 (−0.05); 10 mm → X 9.96 (−0.04), Y 9.88 (−0.12); 5 mm → X 4.99 (−0.01), Y 5.01 (+0.01). X mean error 0.042 mm; Y mean error 0.068 mm; combined mean 0.055 mm. Scored 5/5. Elegoo's claim is ±0.1 mm[42]Parts produced within +/-0.200 mm or +/-0.002 mm/mm, whichever is greater. Manufacturer figure derived from statistical data at 95% dimensional yield; Z accuracy carries an extra -0.000/+slice-height tolerance[3]
Surface quality / VFA / ringing assessmentsThe only structured test scores it poorly, while every impressionistic review praises it. TechRadar's sub-scores: Fine flow control 5/5, Fine negative features 5/5, Bridging 5/5, Overhangs 4/5, but XY resonance 2.5/5 and Z-axis alignment 2.5/5. Against that: Tom's "no color bleeding using the default purge values"; CreativeBloq "layer lines are barely visible, corners and edges are sharp" and "very few of those annoying wispy bits of filament"; 3DwithUS "All lettering came out sharp and clearly defined" at 0.08 mm; TechRadar's own prose "The multifilament printing quality is exceptionally good, with clean lines"[42][30]Not documented
Benchmark print times (source + settings)Tom's Hardware is the only outlet that published settings alongside times: 7× Baby Chameleon (multicolour PLA, 0.2 mm, 160 mm/s avg) 4 h 55 min; Slinky Fidget (PETG, 4 walls, 50 % infill, 0.2 mm, 150 mm/s avg) 4 h 20 min; TPU Air Duster (TPU 95A, 0.12 mm, 50 mm/s) ~2 h; RC Death Racer part (Bambu PAHT-CF, 0.2 mm, 100 mm/s) 2 h 12 min; 7× Utility Knife (Prusa PC Blend, 0.2 mm, 100 mm/s) 6 h 06 min; Voron spool holders (Polymax PC, 5 walls, 0.2 mm, 100 mm/s) 2 h 36 min. 3DwithUS: 4-colour Gengar, 0.14 mm, 4 colours, ~5 in tall, ~14 h; HueForge wall art, 0.08 mm, 100 % infill, lowest speed, ~80 % of the bed, ~6 h; multicolour Benchy ~2 h; "Little Buddha" ~35 min; Elegoo name tag (2 colours) ~1 h. Notebookcheck: average colour change ≈ 1 min 10 s (74 and 78 colour changes on two test models)[30][112]Not documented
First-layer consistency reportsLeaning positive with one specific measured defect. Notebookcheck: "The default z offset is a bit too low resulting in wavy first layers, but lowering the bed by 0.025 mm fixes that." Against that: CreativeBloq "Bed adhesion was excellent, using the textured side of the plate, but not so strong that removal posed any issues"; Tom's reports no first-layer problems across six materials but lists "a cold plate that could use more grip" as a quirk; Notebookcheck also needed a 10-minute 110 °C bed preheat for ASA adhesion[112]Not documented
Review scores from major outlets (list outlet + score + date)TechRadar Pro 4.25/5 (Alastair Jennings, 2026-01-28) — sub-scores Value 5, Design 4, Features 4.5, Performance 4.5 (these four average 4.5, not the 4.25 TechRadar publishes as its headline — a second arithmetic inconsistency in the same review, alongside the "29 out of 30" problem in E5). Tom's Hardware 4/5 (Denise Bertacchi, 2026-02-18). CreativeBloq 9/10 (Rob Redman). 3DwithUS 4.4/5 (Phil Macey, 2026-02-09). GamesRadar+ 5/5 (Benjamin Abbott). Notebookcheck — reviewed 2026-03-02, no numeric score extracted; verdict "Solid entryway into the world of multi-color printing … the hardware is on point but the software needs more tuning". Hackster.io (2026-01-26) and VoxelMatters — positive, unscored[30]Not documented

Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.

Sources for this comparison

  1. firmware/ElegooSlicer_ECC2/Elegoo_Centauri_Carbon_2.json; firmware/ElegooSlicer_ECC2/Elegoo_Centauri_Carbon_2_0.4_nozzle.json; firmware/CentauriCarbon2/README.md L9; docs docs.opencentauri.cc · 2026-08 · doc
  2. firmware/ElegooSlicer_ECC2/Elegoo_Centauri_Carbon_2.json; firmware/ElegooSlicer_ECC2/Elegoo_Centauri_Carbon_2_0.4_nozzle.json; firmware/CentauriCarbon2/README.md L9; docs us.elegoo.com · 2026-08 · doc
  3. Stratasys F123 Series product specification sheet (PSS_FDM_F123Series_0721a, PDF) stratasys.com · 2026-08 · doc
  4. https://tools.prnewswire.com/en-us/live/20813/release/20260119EN65865; https://www.voxelmatters.com/elegoo-debuts-centauri-carbon-2-combo-an-enclosed-multicolor-desktop-3 tools.prnewswire.com · 2026-08 · doc
  5. https://tools.prnewswire.com/en-us/live/20813/release/20260119EN65865; https://www.voxelmatters.com/elegoo-debuts-centauri-carbon-2-combo-an-enclosed-multicolor-desktop-3 voxelmatters.com · 2026-08 · doc
  6. https://tools.prnewswire.com/en-us/live/20813/release/20260119EN65865; https://www.voxelmatters.com/elegoo-debuts-centauri-carbon-2-combo-an-enclosed-multicolor-desktop-3 tomshardware.com · 2026-08 · doc
  7. https://tools.prnewswire.com/en-us/live/20813/release/20260119EN65865; https://www.voxelmatters.com/elegoo-debuts-centauri-carbon-2-combo-an-enclosed-multicolor-desktop-3 hackster.io · 2026-08 · doc
  8. https://www.voxelmatters.com/elegoo-debuts-centauri-carbon-2-combo-... (full regional table, FX dated 2026-01-24/25); https://www.hackster.io/news/... ("United States: $4 voxelmatters.com · 2026-08 · doc
  9. https://www.voxelmatters.com/elegoo-debuts-centauri-carbon-2-combo-... (full regional table, FX dated 2026-01-24/25); https://www.hackster.io/news/... ("United States: $4 hackster.io · 2026-08 · doc
  10. ELEGOO Centauri Carbon 2 Combo Shopify product JSON (price and store publish date) us.elegoo.com · 2026-08 · vendor
  11. https://us.elegoo.com/products/centauri-carbon-2-combo (raw HTML → evidence/elegoo_official_product_page.md); https://us.elegoo.com/products/centauri-carbon-2-combo.json us.elegoo.com · 2026-08 · doc
  12. https://us.elegoo.com/products/centauri-carbon-2-combo (raw HTML → evidence/elegoo_official_product_page.md); https://us.elegoo.com/products/centauri-carbon-2-combo.json notebookcheck.net · 2026-08 · doc
  13. ELEGOO Centauri Carbon 2 product page (Centauri Carbon 2 vs Centauri Carbon side-by-side table) us.elegoo.com · 2026-08 · vendor
  14. evidence/elegoo_cc2_vs_cc1_official_comparison.md; https://us.elegoo.com/collections/all/products.json; https://us.elegoo.com/products/centauri-carbon-2; https://us.elego us.elegoo.com · 2026-08 · doc
  15. https://us.elegoo.com/collections/all/products.json; https://docs.opencentauri.cc/software/updates-cc2/; hackster.io ("closest competitors are the Bambu Lab P1S Combo and docs.opencentauri.cc · 2026-08 · doc
  16. firmware/CentauriCarbon2/debugfile_printer_dsp.cfg L11–13, L41–42, L67–68, L94–95; firmware/ElegooSlicer_ECC2/Elegoo_Centauri_Carbon_2_0.4_nozzle.json project evidence · 2026-08 · local
  17. evidence/elegoo_official_product_page.md; docs/CC2_manual_EN.pdf p.01; tomshardware.com; voxelmatters.com; evidence/elegoo_cc2_vs_cc1_official_comparison.md project evidence · 2026-08 · local
  18. evidence/elegoo_official_product_page.md; docs/CC2_manual_EN.pdf p.01; tomshardware.com ("19.35 kg / 42.65 lbs"); techradar.com body ("42.66 lb"); notebookcheck.net ("abo project evidence · 2026-08 · local
  19. tomshardware.com ("fully enclosed … glass front door … a very large 'top hat'"); techradar.com ("Perspex top … essentially making it almost airtight"); evidence/elegoo_of project evidence · 2026-08 · local
  20. https://www.youtube.com/watch?v=xp-jQ7dljV0 at 18:25-19:05 and 26:35 (Aurora Tech, evidence/auroratech_cc2_combo_transcript.md); firmware/CentauriCarbon2/debugfile_printe youtube.com · 2026-08 · doc
  21. https://www.youtube.com/watch?v=xp-jQ7dljV0 at 18:25-19:05 and 26:35 (Aurora Tech, evidence/auroratech_cc2_combo_transcript.md); firmware/CentauriCarbon2/debugfile_printe github.com · 2026-08 · doc
  22. firmware/CentauriCarbon2/debugfile_printer_dsp.cfg L6; corroborated by tomshardware.com, techradar.com, notebookcheck.net project evidence · 2026-08 · local
  23. docs/CC2_BOM.pdf (Y光轴, Y光轴固定钣金, Y轴光轴固定块, Y轴轴承固定钣金); tomshardware.com project evidence · 2026-08 · local
  24. docs/CC2_BOM.pdf; firmware/CentauriCarbon2/debugfile_printer_dsp.cfg L38, L64 project evidence · 2026-08 · local
  25. docs/CC2_BOM.pdf; https://us.elegoo.com/products/centauri-carbon-2-combo ("Dual 4260 stepper motors"); https://docs.opencentauri.cc/hardware/CC2/toolhead/ ("10T NEMA14 (r docs.opencentauri.cc · 2026-08 · doc
  26. docs/CC2_BOM.pdf; https://us.elegoo.com/products/centauri-carbon-2-combo ("Dual 4260 stepper motors"); https://docs.opencentauri.cc/hardware/CC2/toolhead/ ("10T NEMA14 (r docs.opencentauri.cc · 2026-08 · doc
  27. firmware/CentauriCarbon2/debugfile_printer_dsp.cfg L47–58 (X), L73–84 (Y), L100–110 (Z), L145–152 (E); https://docs.opencentauri.cc/hardware/CC2/mainboard/ ("Stepper driv docs.opencentauri.cc · 2026-08 · doc
  28. firmware/CentauriCarbon2/debugfile_printer_dsp.cfg L37, L51 (X); L63, L77 (Y); L89, L104 (Z); L119, L148 (E) project evidence · 2026-08 · local
  29. evidence/elegoo_official_product_page.md; docs/CC2_manual_EN.pdf p.01; tomshardware.com; techradar.com; notebookcheck.net; voxelmatters.com project evidence · 2026-08 · local
  30. evidence/elegoo_official_product_page.md; tomshardware.com (per-print average speeds); https://3dwithus.com/elegoo-centauri-carbon-2-combo-3d-printer-review 3dwithus.com · 2026-08 · doc
  31. firmware/CentauriCarbon2/debugfile_printer_dsp.cfg L7, L9; firmware/ElegooSlicer_ECC2/Elegoo_Centauri_Carbon_2_0.4_nozzle.json project evidence · 2026-08 · local
  32. evidence/elegoo_official_product_page.md (both rows present); evidence/elegoo_cc2_vs_cc1_official_comparison.md project evidence · 2026-08 · local
  33. firmware/CentauriCarbon2/debugfile_printer_dsp.cfg L7, L9 project evidence · 2026-08 · local
  34. firmware/CentauriCarbon2/debugfile_printer_dsp.cfg L8, L10; firmware/ElegooSlicer_ECC2/Elegoo_Centauri_Carbon_2_0.4_nozzle.json (incl. machine_start_gcode) project evidence · 2026-08 · local
  35. firmware/CentauriCarbon2/debugfile_printer_dsp.cfg L14; firmware/ElegooSlicer_ECC2/Elegoo_Centauri_Carbon_2_0.4_nozzle.json project evidence · 2026-08 · local
  36. firmware/ElegooSlicer_ECC2/Elegoo_{PLA,ABS,PC,PLA-CF,PETG-CF,PETG,PET-CF,PAHT-CF,TPU_95A}_@ECC2.json (filament_max_volumetric_speed) project evidence · 2026-08 · local
  37. — project evidence · 2026-08 · local
  38. https://www.creativebloq.com/3d/3d-printing/i-tested-the-elegoo-centauri-carbon-2-and-now-i-want-to-print-everything-in-multicolour-glory; https://3dwithus.com/elegoo-cen creativebloq.com · 2026-08 · doc
  39. https://www.creativebloq.com/3d/3d-printing/i-tested-the-elegoo-centauri-carbon-2-and-now-i-want-to-print-everything-in-multicolour-glory; https://3dwithus.com/elegoo-cen voxelmatters.com · 2026-08 · doc
  40. https://www.creativebloq.com/3d/3d-printing/i-tested-the-elegoo-centauri-carbon-2-and-now-i-want-to-print-everything-in-multicolour-glory; https://3dwithus.com/elegoo-cen smith3d.com · 2026-08 · doc
  41. firmware/CentauriCarbon2/debugfile_printer_dsp.cfg L277–282, L292–300 project evidence · 2026-08 · local
  42. https://www.techradar.com/pro/elegoo-centauri-carbon-2-combo-3d-printer-review (per-test scores: Dimensional accuracy 5, Fine flow control 5, Fine negative features 5, Ov techradar.com · 2026-08 · doc
  43. firmware/CentauriCarbon2/debugfile_printer_dsp.cfg L135; firmware/ElegooSlicer_ECC2/*_@ECC2.json (enable_pressure_advance: ['1']) project evidence · 2026-08 · local
  44. firmware/CentauriCarbon2/debugfile_printer_dsp.cfg L135; firmware/ElegooSlicer_ECC2/Elegoo_ABS_@ECC2.json, Elegoo_PC_@ECC2.json, Elegoo_PAHT-CF_@ECC2.json, Elegoo_TPU_95A project evidence · 2026-08 · local
  45. firmware/CentauriCarbon2/debugfile_printer_dsp.cfg L517–588 ([load_cell_probe], sclk_pin=bed_sensor:PA5, dout_pin=bed_sensor:PA4); https://docs.opencentauri.cc/hardware/C docs.opencentauri.cc · 2026-08 · doc
  46. firmware/CentauriCarbon2/debugfile_printer_dsp.cfg L136–142; firmware/ElegooSlicer_ECC2/Elegoo_Centauri_Carbon_2_0.4_nozzle.json project evidence · 2026-08 · local
  47. firmware/CentauriCarbon2/debugfile_printer_dsp.cfg L123 (filament_diameter=1.75); evidence/elegoo_official_product_page.md; docs/CC2_manual_EN.pdf project evidence · 2026-08 · local
  48. Searched: evidence/elegoo_official_product_page.md, docs/CC2_manual_EN.pdf, evidence/elegoo_cc2_vs_cc1_official_comparison.md, all eight reviews, and OpenCentauri's toolh project evidence · 2026-08 · local
  49. firmware/CentauriCarbon2/debugfile_printer_dsp.cfg L431–436 ([filament_load_unload]); L344–366 ([canvas_dev] pre_load_fila_dist=150, load_fila_dist=1000, unload_fila_dist project evidence · 2026-08 · local
  50. https://docs.opencentauri.cc/hardware/CC2/toolhead/ ("The Toolhead board has a 2x4 pin port at the bottom. This connector links to a separate PCB that breaks out the requ us.elegoo.com · 2026-08 · doc
  51. firmware/CentauriCarbon2/debugfile_printer_dsp.cfg L126, L133–134; firmware/CentauriCarbon2/debugfile_printer.cfg L119, L125–126; https://github.com/elegooofficial/Centau github.com · 2026-08 · doc
  52. firmware/CentauriCarbon2/debugfile_printer_dsp.cfg L122 (nozzle_diameter=0.4); evidence/elegoo_official_product_page.md (spec "Nozzle Diameter 0.4 mm"; "What's in the Box project evidence · 2026-08 · local
  53. https://us.elegoo.com/products/0-4-mm-brass-hardened-steel-nozzle-kit-for-centauri-carbon-series; docs/CC2_BOM.pdf (黄铜硬化钢喷嘴); evidence/elegoo_official_product_page.md ("N us.elegoo.com · 2026-08 · doc
  54. https://us.elegoo.com/products/multi-size-brass-hardened-steel-nozzle-kit-for-centauri-carbon-series; firmware/ElegooSlicer_ECC2/Elegoo_Centauri_Carbon_2.json (nozzle_dia us.elegoo.com · 2026-08 · doc
  55. evidence/elegoo_official_product_page.md ("Heat Break: Titanium Alloy"); evidence/elegoo_cc2_vs_cc1_official_comparison.md; https://docs.opencentauri.cc/hardware/CC2/ ("H docs.opencentauri.cc · 2026-08 · doc
  56. firmware/CentauriCarbon2/debugfile_printer_dsp.cfg L163–165; evidence/elegoo_official_product_page.md; docs/CC2_manual_EN.pdf p.01 project evidence · 2026-08 · local
  57. https://docs.opencentauri.cc/hardware/CC2/bed/ ("Danger: The Bed runs on mains AC current at 110/220 V"; "the CC2 uses a solid state relay (SSR) board to control the main west3d.com · 2026-08 · doc
  58. Searched all eight CC2 reviews (Tom's, TechRadar, Notebookcheck, Hackster, GamesRadar, 3DwithUS, CreativeBloq, VoxelMatters) plus general web search project evidence · 2026-08 · local
  59. https://us.elegoo.com/products/pei-plate-for-centauri-carbon ("Enhance your 3D prints with a dual-sided plate that delivers strong adhesion for PLA and a premium carbon f us.elegoo.com · 2026-08 · doc
  60. Searched all eight CC2 reviews plus targeted web searches for thermal-camera/FLIR bed-uniformity tests of the CC2; also checked My Tech Fun's bed-heating comparison work project evidence · 2026-08 · local
  61. firmware/CentauriCarbon2/debugfile_printer_dsp.cfg L589–604; firmware/ElegooSlicer_ECC2/Elegoo_Centauri_Carbon_2_0.4_nozzle.json project evidence · 2026-08 · local
  62. docs/CC2_manual_EN.pdf (assembly section — "remove the foam … marked in blue to unlock the heated bed"; no levelling-screw procedure); tomshardware.com ("After unpacking project evidence · 2026-08 · local
  63. firmware/CentauriCarbon2/debugfile_printer_dsp.cfg (complete section list contains no [z_tilt]/[quad_gantry_level]); single [stepper_z] at L85; tomshardware.com ("three l project evidence · 2026-08 · local
  64. firmware/ElegooSlicer_ECC2/Elegoo_Centauri_Carbon_2_0.4_nozzle.json (machine_start_gcode); firmware/CentauriCarbon2/debugfile_printer_dsp.cfg L644+ ([g180] S7/S8/S910/S91 project evidence · 2026-08 · local
  65. firmware/ElegooSlicer_ECC2/Elegoo_Centauri_Carbon_2_0.4_nozzle.json (machine_pause_gcode, change_filament_gcode, machine_start_gcode M6211 A1 L200 …); firmware/CentauriCa project evidence · 2026-08 · local
  66. https://docs.opencentauri.cc/hardware/CC2/misc/ ("Auxiliary fan type: Custom 12032 radial fan … P/N EFC-12J24H … 0.8 A @ 24 V … mounted on the left panel with intake from docs.opencentauri.cc · 2026-08 · doc
  67. firmware/CentauriCarbon2/debugfile_printer_dsp.cfg L198–212 ([cavity_fan]), L302–316 ([servo printer_servo]); https://docs.opencentauri.cc/hardware/CC2/misc/ ("The exhaus us.elegoo.com · 2026-08 · doc
  68. https://docs.opencentauri.cc/hardware/CC2/mainboard/ ("SoC AllWinner R528-S3; Memory 128 MB in-chip; Storage 8 gb eMMC"); https://raw.githubusercontent.com/OpenCentauri/o raw.githubusercontent.com · 2026-08 · doc
  69. evidence/elegoo_official_product_page.md ("Power Input: 100–240 VAC 50/60 Hz"); docs/CC2_manual_EN.pdf p.01; techradar.com ("Input Power: AC 100–240 V, 50/60 Hz"); notebo project evidence · 2026-08 · local
  70. firmware/CentauriCarbon2/README.md; firmware/CentauriCarbon2/debugfile_printer_dsp.cfg (whole file); firmware/ElegooSlicer_ECC2/Elegoo_Centauri_Carbon_2_0.4_nozzle.json ( github.com · 2026-08 · doc
  71. firmware/CentauriCarbon2/README.md; firmware/CentauriCarbon2/debugfile_printer_dsp.cfg (whole file); firmware/ElegooSlicer_ECC2/Elegoo_Centauri_Carbon_2_0.4_nozzle.json ( freethecode.lol · 2026-08 · doc
  72. https://github.com/elegooofficial/CentauriCarbon2 (API: created 2026-03-11T10:10:07Z, pushed 2026-03-12T08:19:55Z, 3 commits, license GPL-3.0); https://github.com/elegooo github.com · 2026-08 · doc
  73. https://github.com/elegooofficial/CentauriCarbon2 (API: created 2026-03-11T10:10:07Z, pushed 2026-03-12T08:19:55Z, 3 commits, license GPL-3.0); https://github.com/elegooo github.com · 2026-08 · doc
  74. https://github.com/elegooofficial/CentauriCarbon2 (API: created 2026-03-11T10:10:07Z, pushed 2026-03-12T08:19:55Z, 3 commits, license GPL-3.0); https://github.com/elegooo github.com · 2026-08 · doc
  75. https://github.com/elegooofficial/CentauriCarbon2 (API: created 2026-03-11T10:10:07Z, pushed 2026-03-12T08:19:55Z, 3 commits, license GPL-3.0); https://github.com/elegooo all3dp.com · 2026-08 · doc
  76. https://docs.opencentauri.cc/software/updates-cc2/ ("v02.00.02.00 (Released 28/05/2026) … SSH disabled — This release removes the SSH process entirely, making it more dif docs.opencentauri.cc · 2026-08 · doc
  77. https://docs.opencentauri.cc/software/updates-cc2/ ("v02.00.02.00 (Released 28/05/2026) … SSH disabled — This release removes the SSH process entirely, making it more dif docs.opencentauri.cc · 2026-08 · doc
  78. https://docs.opencentauri.cc/software/updates-cc2/ ("v02.00.02.00 (Released 28/05/2026) … SSH disabled — This release removes the SSH process entirely, making it more dif github.com · 2026-08 · doc
  79. https://docs.opencentauri.cc/software/updates-cc2/ ("v02.00.02.00 (Released 28/05/2026) … SSH disabled — This release removes the SSH process entirely, making it more dif docs.opencentauri.cc · 2026-08 · doc
  80. firmware/CentauriCarbon2/ipkg-build_run_printer.sh (elegoo_printer … -a /tmp/elegoo_uds); firmware/CentauriCarbon2/debugfile_printer.cfg L11–12 (broker_address=tcp://brok docs.opencentauri.cc · 2026-08 · doc
  81. firmware/CentauriCarbon2/ipkg-build_run_printer.sh (elegoo_printer … -a /tmp/elegoo_uds); firmware/CentauriCarbon2/debugfile_printer.cfg L11–12 (broker_address=tcp://brok github.com · 2026-08 · doc
  82. firmware/CentauriCarbon2/ipkg-build_run_printer.sh (elegoo_printer … -a /tmp/elegoo_uds); firmware/CentauriCarbon2/debugfile_printer.cfg L11–12 (broker_address=tcp://brok github.com · 2026-08 · doc
  83. https://docs.opencentauri.cc/patched-firmware/features/; https://github.com/OpenCentauri/cc-fw-tools; https://github.com/OpenCentauri/cosmos; https://github.com/OpenCenta docs.opencentauri.cc · 2026-08 · doc
  84. https://docs.opencentauri.cc/patched-firmware/features/; https://github.com/OpenCentauri/cc-fw-tools; https://github.com/OpenCentauri/cosmos; https://github.com/OpenCenta github.com · 2026-08 · doc
  85. https://docs.opencentauri.cc/patched-firmware/features/; https://github.com/OpenCentauri/cc-fw-tools; https://github.com/OpenCentauri/cosmos; https://github.com/OpenCenta github.com · 2026-08 · doc
  86. https://docs.opencentauri.cc/patched-firmware/features/; https://github.com/OpenCentauri/cc-fw-tools; https://github.com/OpenCentauri/cosmos; https://github.com/OpenCenta github.com · 2026-08 · doc
  87. https://docs.opencentauri.cc/patched-firmware/features/; https://github.com/OpenCentauri/cc-fw-tools; https://github.com/OpenCentauri/cosmos; https://github.com/OpenCenta github.com · 2026-08 · doc
  88. https://docs.opencentauri.cc/patched-firmware/features/; https://github.com/OpenCentauri/cc-fw-tools; https://github.com/OpenCentauri/cosmos; https://github.com/OpenCenta github.com · 2026-08 · doc
  89. https://docs.opencentauri.cc/patched-firmware/features/; https://github.com/OpenCentauri/cc-fw-tools; https://github.com/OpenCentauri/cosmos; https://github.com/OpenCenta github.com · 2026-08 · doc
  90. firmware/CentauriCarbon2/debugfile_printer_dsp.cfg L644+ ([g180] table), L307–316 (M2801_*), L329, L399, L424 and L432–435 (M2202 gcode_action_report=… in the CANVAS-runo docs.opencentauri.cc · 2026-08 · doc
  91. https://docs.opencentauri.cc/software/updates-cc2/ (SSH removal + downgrade block + repacked v01.03.02.51 download); https://docs.opencentauri.cc/patched-firmware/ (CC2 n github.com · 2026-08 · doc
  92. firmware/CentauriCarbon2/ipkg-build_readme.md; firmware/CentauriCarbon2/ipkg-build_run_printer.sh L13–15; firmware/CentauriCarbon2/ipkg-build_update_ipk.sh; firmware/Cent docs.opencentauri.cc · 2026-08 · doc
  93. https://raw.githubusercontent.com/OpenCentauri/oc-linux/opencentauri/arch/arm/configs/sun8iw20p1smp_defconfig and.../sun8iw20p1smp_t113_auto_defconfig (grep: no CONFIG_TU raw.githubusercontent.com · 2026-08 · doc
  94. evidence/elegoo_official_product_page.md ("5-inch Color Capacitive Touch Screen"); https://docs.opencentauri.cc/hardware/CC2/screen/ ("The CC2 touchscreen is 5.0 inches, docs.opencentauri.cc · 2026-08 · doc
  95. evidence/elegoo_official_product_page.md ("5-inch Color Capacitive Touch Screen"); https://docs.opencentauri.cc/hardware/CC2/screen/ ("The CC2 touchscreen is 5.0 inches, github.com · 2026-08 · doc
  96. evidence/elegoo_official_product_page.md ("5-inch Color Capacitive Touch Screen"); https://docs.opencentauri.cc/hardware/CC2/screen/ ("The CC2 touchscreen is 5.0 inches, github.com · 2026-08 · doc
  97. tomshardware.com ("nice reminder to unlock the bed", loading screens, filament naming); techradar.com; creativebloq.com ("Head to the load screen and click on reel one … github.com · 2026-08 · doc
  98. evidence/elegoo_official_product_page.md ("Connectivity: USB, Wi-Fi"); docs/CC2_manual_EN.pdf p.01 ("Connectivity: USB Drive, Wi-Fi") and p.02 ("USB Drive Port"); https:/ github.com · 2026-08 · doc
  99. docs/CC2_manual_EN.pdf pp.19–20 ("LAN (Network) Printing … The assigned IP address will display once successfully connected … Ensure your computer and printer are on the github.com · 2026-08 · doc
  100. https://docs.opencentauri.cc/hardware/CC2/camera/ (full table); evidence/elegoo_official_product_page.md ("Camera: Yes"); docs/CC2_manual_EN.pdf p.02 ("Camera"); https:// docs.opencentauri.cc · 2026-08 · doc
  101. tomshardware.com ("excellent camera for print monitoring and AI detection"); https://www.notebookcheck.net/Elegoo-Centauri-Carbon-2-3D-printer-review-... ("Coming to the notebookcheck.net · 2026-08 · doc
  102. firmware/CentauriCarbon2/debugfile_printer_dsp.cfg L589–596 (mesh), L517–588 (probe), L292–300 (shaper_calibrate_gcode), L632–641 ([z_compensation]), L644+ ([g180] S1/S2/ creativebloq.com · 2026-08 · doc
  103. firmware/CentauriCarbon2/debugfile_printer_dsp.cfg L444–445 ([pid_calibrate]), L128–131 (extruder PID), L158–161 (bed PID) project evidence · 2026-08 · local
  104. firmware/CentauriCarbon2/debugfile_printer_dsp.cfg (searched: no flow-calibration macro); firmware/ElegooSlicer_ECC2/Elegoo_PAHT-CF_@ECC2.json (filament_flow_ratio); toms project evidence · 2026-08 · local
  105. firmware/CentauriCarbon2/debugfile_printer_dsp.cfg (no tension macro); docs/CC2_manual_EN.pdf (no tensioning section); docs/CC2_BOM.pdf (tensioning springs and idler brac project evidence · 2026-08 · local
  106. firmware/ElegooSlicer_ECC2/Elegoo_Centauri_Carbon_2_0.4_nozzle.json (scan_first_layer: 1); firmware/CentauriCarbon2/debugfile_printer_dsp.cfg L644+ ([g180] S1, S2, S911) project evidence · 2026-08 · local
  107. firmware/CentauriCarbon2/debugfile_printer_dsp.cfg and debugfile_printer.cfg (full section lists — no skew section); docs/CC2_manual_EN.pdf project evidence · 2026-08 · local
  108. tomshardware.com (step-by-step; "the whole process took less than twenty minutes from unboxing to printing"); https://3dwithus.com/... ("15–20 minutes"); https://www.voxe 3dwithus.com · 2026-08 · doc
  109. firmware/CentauriCarbon2/debugfile_printer_dsp.cfg L607–630 ([por] incl. charge_pin, charge_time, shutdown_pins), L223 (power_outage_enable=1) project evidence · 2026-08 · local
  110. evidence/elegoo_official_product_page.md (spec row "Supported Filament", incl. footnotes 3 and 4); firmware/ElegooSlicer_ECC2/Elegoo_Centauri_Carbon_2.json (default_mater api.github.com · 2026-08 · doc
  111. tomshardware.com (TPU 95A print, settings and result); firmware/ElegooSlicer_ECC2/Elegoo_TPU_95A_@ECC2.json, Elegoo_PLA_@ECC2.json, Elegoo_PETG_@ECC2.json; evidence/elego project evidence · 2026-08 · local
  112. https://www.youtube.com/watch?v=xp-jQ7dljV0 at 18:25-19:30 and 26:35 (Aurora Tech, Danville CA, 110-120 V; evidence/auroratech_cc2_combo_transcript.md); https://www.noteb notebookcheck.net · 2026-08 · doc
  113. firmware/ElegooSlicer_ECC2/ (14 profiles downloaded and inspected); https://api.github.com/repos/elegooofficial/ElegooSlicer/contents/resources/profiles/Elegoo/{machine,p api.github.com · 2026-08 · doc
  114. docs/CC2_manual_EN.pdf (searched full extracted text for "FCC", "CE", "UKCA", "RoHS", "WEEE", "UL", "ETL", "certif", "complian", "declaration" — zero hits); evidence/eleg project evidence · 2026-08 · local
  115. firmware/CentauriCarbon2/debugfile_printer_dsp.cfg L133–134 (extruder), L163–165 (bed), L256–258 (chamber), L437–442 ([idle_timeout]), L536–537 (probe force), L141–142 (m project evidence · 2026-08 · local
  116. Searched: https://github.com/elegooofficial/CentauriCarbon2/issues (all 11, all states); https://github.com/OpenCentauri/cc-fw-tools/issues (40 most recent); https://free github.com · 2026-08 · doc
  117. Searched: https://github.com/elegooofficial/CentauriCarbon2/issues (all 11, all states); https://github.com/OpenCentauri/cc-fw-tools/issues (40 most recent); https://free github.com · 2026-08 · doc
  118. evidence/elegoo_official_product_page.md (footnote 2: "Tested with Elegoo PLA filament in Silent Mode with the auxiliary part cooling fan turned off"); firmware/CentauriC project evidence · 2026-08 · local
  119. Searched all eight CC2 reviews plus targeted web search for CC2 wattage/power-meter tests; evidence/elegoo_official_product_page.md; docs/CC2_manual_EN.pdf p.01 project evidence · 2026-08 · local
  120. evidence/elegoo_official_product_page.md (full Refund & Warranty tables as rendered on the product page, incl. the consumables list and the CANVAS row); docs/CC2_manual_E matterhackers.com · 2026-08 · doc
  121. Discord member counts via web search of https://discord.com/servers/opencentauri-1367538416539013122 and https://discord.com/invite/elegoo-official-969282195552346202; ht discord.com · 2026-08 · doc
  122. Discord member counts via web search of https://discord.com/servers/opencentauri-1367538416539013122 and https://discord.com/invite/elegoo-official-969282195552346202; ht discord.com · 2026-08 · doc
  123. Discord member counts via web search of https://discord.com/servers/opencentauri-1367538416539013122 and https://discord.com/invite/elegoo-official-969282195552346202; ht api.github.com · 2026-08 · doc
  124. Discord member counts via web search of https://discord.com/servers/opencentauri-1367538416539013122 and https://discord.com/invite/elegoo-official-969282195552346202; ht api.github.com · 2026-08 · doc
  125. Discord member counts via web search of https://discord.com/servers/opencentauri-1367538416539013122 and https://discord.com/invite/elegoo-official-969282195552346202; ht docs.opencentauri.cc · 2026-08 · doc
  126. https://api.github.com/orgs/OpenCentauri/repos; https://github.com/OpenCentauri/cad; https://github.com/OpenCentauri/cad/issues/13 ("Add CC2 CAD"); https://docs.opencenta github.com · 2026-08 · doc
  127. https://api.github.com/orgs/OpenCentauri/repos; https://github.com/OpenCentauri/cad; https://github.com/OpenCentauri/cad/issues/13 ("Add CC2 CAD"); https://docs.opencenta docs.opencentauri.cc · 2026-08 · doc