3D Printing InfoPrinter comparison
Bambu Lab X2D vs Original Prusa MINI+
Compare hardware, build volume, printing specifications, dated prices and sources.
2 selected · all documented properties
Open these two in the interactive comparisonMore Bambu Lab X2D comparisonsMore Original Prusa MINI+ comparisons
| Property | Bambu Lab X2DCOREXY | Original Prusa MINI+BEDSLINGER |
|---|---|---|
| Identity | ||
| Brand | Bambu Lab | Prusa Research |
| Class | COREXY | BEDSLINGER |
| Identity & Market | ||
| Manufacturer & exact marketed model name (verify the exact product identity first) | Bambu Lab X2D; spec PDF header "X2D Spec"[1] | Original Prusa MINI+ Semi-assembled 3D Printer[2] |
| Street price (USD; dated snapshot per entry) | From $649.00 on the Bambu Lab US store, Aug 2026; the compare page shows the same $649 figure[3] | $508.33 on prusa3d.com, Aug 2026[4] |
| Variants & sibling models — and how to tell them apart (spec-contamination risk) | Dual-nozzle machine: a main hotend with a permanent-magnet synchronous extruder motor and an auxiliary hotend with a plain stepper motor, so the two nozzles are not equivalent. Bambu publishes four different build volumes depending on which nozzle is used, and a shorter list of materials for the auxiliary nozzle. Physical dimensions (392x406x478 mm) are shared with the P2S but the X2D is 16.25 kg against the P2S's 14.9 kg[1][5] | Sold semi-assembled and, historically, as a kit; also offered in an Enclosure Bundle. Distinguish from the larger i3-family machines - the MINI+ is Bowden-fed with 2209 drivers, a 280 C nozzle ceiling and a 100 C bed, all lower than the MK3S+/MK4S. Note that Prusa's own MINI+ page carries an "Awards & Press Reviews" paragraph that is entirely about the MK3S, not the MINI+[2][6] |
| Market position: superseded? successor announced? | Current model, launched into the slot vacated by the discontinued X1-Carbon[3] | Not documented |
| Physical & Frame | ||
| Build volume X×Y×Z (mm) — advertised vs actually usable | Main nozzle 256 x 256 x 260 mm; auxiliary nozzle 235.5 x 256 x 256 mm; dual-nozzle printing 235.5 x 256 x 256 mm; total volume for two nozzles 256 x 256 x 260 mm. The sortable figure below is the main-nozzle volume[1] | 180 x 180 x 180 mm (manufacturer figure)[2] |
| Machine footprint (mm) & clearance needed (cable/spool overhang) | 392 x 406 x 478 mm[1] | 380 x 330 x 380 mm (X x Y x Z), stated without the spool holder and external PSU - the external PSU brick needs additional desk space[2] |
| Net weight (kg) | 16.25 kg net[1] | 4.5 kg without spool holder and external PSU[2] |
| Frame construction & material | Plastic and steel chassis; plastic, glass and metal outer frame[1] | Not documented |
| Enclosure: open / enclosed; panel material; door/lid | Fully enclosed with a door sensor, active chamber heating to 65 C, and a G3 + H12 HEPA + granulated coconut-shell carbon filter stack with an external exhaust fan[1] | Open frame; sold with an optional Enclosure bundle[2] |
| Passive chamber temperature reached (if enclosed; measured values preferred) | Active chamber heating, maximum 65 C (manufacturer figure)[1] | Not documented |
| Kinematics & Motion Hardware | ||
| Kinematics (bedslinger i3 / CoreXY / other) | CoreXY - not stated in the spec sheet; Bambu groups the X2D with its enclosed CoreXY machines and publishes the same 20000 mm/s2 acceleration figure[1] | Not documented |
| Stepper drivers (exact model e.g. TMC2209; UART/SPI; sensorless homing?) | Not documented | Trinamic 2209 silent stepper drivers, with sensorless homing on the X and Y axes[2] |
| Speed & Acceleration | ||
| Max print speed (claimed, mm/s) | 1000 mm/s max toolhead speed (manufacturer claim); no independent measurement found[1] | Not documented |
| Max acceleration (claimed, mm/s²) | 20000 mm/s2 max toolhead acceleration (manufacturer claim)[1] | Not documented |
| Max volumetric flow claimed (mm³/s) | 40 mm3/s, measured by Bambu on a 250 mm round single-wall model in Bambu ABS at 280 C[1] | Not documented |
| Extruder | ||
| Type (direct drive / bowden) & design name | Two direct-drive extruders: main extruder with hardened-steel gears driven by a Bambu high-precision permanent-magnet synchronous motor, auxiliary extruder with hardened-steel gears driven by a stepper motor[1] | Bowden extruder with 3:1 gearing - the only current Prusa FFF machine that is not direct drive[2] |
| Gear ratio & drive gear material | Not documented | 3:1 extruder gearing[2] |
| Hotend & Nozzle | ||
| Hotend design (proprietary/standard; quick-swap mechanism?) | Dual hardened-steel nozzles; 0.4 mm included, 0.2/0.4/0.6/0.8 mm supported; built-in filament cutter[1] | Not documented |
| Max nozzle temp claimed AND firmware max temp limit (both values) | 300 C claimed max nozzle temperature[1] | 280 C claimed max nozzle temperature - lower than the 290-300 C of the i3-family machines[2] |
| Heated Bed & Surface | ||
| Max bed temp claimed AND firmware limit | 120 C max heatbed temperature[1] | 100 C max heatbed temperature[2] |
| Bed surface (material, texture, coating), single/double-sided | Flexible steel plate, Textured PEI included; Smooth PEI, Cool Plate SuperTack and Engineering Plate supported[1] | Removable magnetic steel sheets in several surface finishes; heatbed with cold-corner compensation[2] |
| Leveling & Z-Offset | ||
| Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe) | Not documented | SuperPINDA inductive probe with no temperature drift, driving automatic mesh bed levelling[2] |
| Filament Handling & Detection | ||
| Filament runout sensor (type, location) | Yes - run-out sensor, tangle sensor and door sensor; odometry with AMS[1] | Not documented |
| Cooling & Air Handling | ||
| Part-cooling fan(s): count, size, ducting design | Part-cooling fan, hotend cooling fan, main control board fan, chamber heat-circulation fan, auxiliary part-cooling fan and external exhaust fan, all closed-loop controlled[1] | Not documented |
| Electronics & Power | ||
| Mainboard model & MCU (exact chip markings if teardowns exist) | Motion controller dual-core Cortex-M4 plus single-core Cortex-M7; application processor quad-core ARM with a dedicated NPU (2 TOPS per the compare page)[1][7] | Custom 32-bit board of Prusa's Buddy family; the MINI/MINI+ is covered by the same Prusa-Firmware-Buddy source tree as the MK4, XL and CORE One. The exact board revision is not given on the product page[2][8] |
| Total rated power draw | High-voltage version 1600 W at 220 V, low-voltage version 1100 W at 110 V; steady state 250 W printing PLA and 550 W printing PC at 25 C ambient[1] | Not documented |
| Firmware & Openness | ||
| Firmware base & current version (Klipper fork / Marlin fork / proprietary) | Closed-source proprietary firmware - not a Klipper or Marlin derivative, and no printer-firmware source is published. The bambulab GitHub organisation carries 11 repositories (Bambu Studio, wxWidgets/boost/ffmpeg forks, the wiki); none is printer firmware. Updates are delivered over the air via Bambu Studio / Bambu Handy[9] | Open-source Prusa Buddy firmware. The source tree (prusa3d/Prusa-Firmware-Buddy on GitHub) explicitly covers the Original Prusa MINI/MINI+, MK4, XL and CORE One and was last pushed to in August 2026. Updates are applied from a USB drive, through Prusa Connect or through the Prusa mobile app[8][10] |
| Connectivity, UI & Camera | ||
| Display: size, type, touch? | 5-inch 1280x720 touchscreen[1] | 2.8-inch 65k-colour graphic screen with G-code preview[2] |
| On-device UI capabilities (model preview, per-object controls, etc.) | Touchscreen plus mobile app and PC app[1] | On-device colour UI with G-code preview; remote print management through Prusa Connect[2] |
| WiFi (band/standard), Ethernet, USB ports, SD/flash-drive | Dual-band Wi-Fi (802.11 a/b/g/n), built-in 8 GB eMMC and a USB port; Ethernet not available, no network kill switch, no 802.1X[1] | USB port, RJ-45 Ethernet, optional ESP Wi-Fi module (sold separately); compatible with Prusa Connect[2] |
| Camera: built-in / optional? Resolution & framerate (verify — marketing often omits real fps) | Two cameras: live-view 1920x1080 and a toolhead camera at 1600x1200[1] | Not documented |
| Calibration Routines & QoL | ||
| Assembly level & time from unbox to first print | Not documented | Semi-assembled: Prusa ships it in a small number of pre-built sections; also historically sold as a full kit[2] |
| Materials Support | ||
| Officially supported filament list | Main hotend: PLA, PETG, ABS, ASA, TPU, support materials, PET, PA, PC, PVA and carbon/glass-fibre reinforced PLA, PETG, ABS, ASA, PA6, PAHT, PPA, PET. Auxiliary hotend drops PPA-CF/GF and excludes PLA Aero; PLA Silk, PETG-CF, ASA-CF, PA6-CF, TPU for AMS and PA/PET support material are flagged "print with caution" on the auxiliary nozzle[1] | PLA, PETG, ASA, ABS, PC, CPE, PVA/BVOH, PVB, HIPS, PP, Flex, nGen, Nylon, Woodfill and other filled materials (Prusa's own list; the 100 C bed and open frame are the practical limit for ABS/ASA)[2] |
| Safety | ||
| Thermal runaway protection (verify in firmware source if at all possible) | Not documented | Three thermistors and fan RPM sensors are fitted, and the firmware is open-source and auditable (Prusa-Firmware-Buddy); Prusa does not describe the thermal-runaway implementation on the product page[2][8] |
| Reliability, Support & Ecosystem | ||
| Warranty length & support reputation (evidence, not vibes) | 2-year limited warranty for consumers in the US, Canada, the EU, Switzerland, Norway and Iceland; 1 year in the rest of the world. Bambu Lab's own policy records the US/Canada term as a 2026 extension from one year to two[11] | 2-year warranty for consumers in the EU, Liechtenstein, Switzerland, Norway and Iceland; 1 year for EU enterprises and 1 year for the rest of the world, which includes the United States. A printer bought from a reseller or privately carries 1 year from the original delivery date and is handled by the reseller. Prusa advertises 24/7 chat and e-mail support in seven languages[12][10] |
Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.
Sources for this comparison
- Bambu Lab X2D Spec (PDF) store.bblcdn.com · 2026-08 · doc
- Original Prusa MINI+ Semi-assembled 3D Printer product page (Technical Parameters + Full Features List, January 2025 Edition) prusa3d.com · 2026-08 · vendor
- Bambu Lab US Store - 3D Printers collection listing (base prices, Aug 2026) us.store.bambulab.com · 2026-08 · vendor
- Prusa 3D printers category listing with live e-shop prices, Aug 2026 prusa3d.com · 2026-08 · vendor
- Bambu Lab P2S Spec Sheet (PDF) store.bblcdn.com · 2026-08 · doc
- Original Prusa i3 MK3S+ 10th Anniversary Edition product page (Technical Parameters + Full Features List) prusa3d.com · 2026-08 · vendor
- Bambu Lab - Compare all 3D printers (A2L / X2D / H2C columns) bambulab.com · 2026-08 · vendor
- GitHub - prusa3d/Prusa-Firmware-Buddy (firmware for MINI, MK4, XL and CORE One) github.com · 2026-08 · doc
- GitHub - bambulab organisation repository list (11 repos, checked Aug 2026) github.com · 2026-08 · doc
- Original Prusa MK4S 3D Printer product page (Technical Parameters + CORE One+/MK4S/XL comparison table) prusa3d.com · 2026-08 · vendor
- Bambu Lab Warranty Policy bambulab.com · 2026-08 · vendor
- Prusa Knowledge Base - Warranty help.prusa3d.com · 2026-08 · doc