3D Printing InfoPrinter comparison
Bambu Lab X2D vs Prusa CORE One L+
Compare hardware, build volume, printing specifications, dated prices and sources.
2 selected · all documented properties
Open these two in the interactive comparisonMore Bambu Lab X2D comparisonsMore Prusa CORE One L+ comparisons
| Property | Bambu Lab X2DCOREXY | Prusa CORE One L+COREXY |
|---|---|---|
| Identity | ||
| Brand | Bambu Lab | Prusa Research |
| Class | COREXY | COREXY |
| Identity & Market | ||
| Manufacturer & exact marketed model name (verify the exact product identity first) | Bambu Lab X2D; spec PDF header "X2D Spec"[1] | Prusa CORE One L+[2] |
| Release date (announcement and actual shipping) | Not documented | The CORE One L+ refresh was announced on 13 August 2026 and went on sale immediately, with the first assembled units shipping at once; it adds GT1.5 belts and an integrated nozzle wiper to the CORE One L[3] |
| Street price (USD; dated snapshot per entry) | From $649.00 on the Bambu Lab US store, Aug 2026; the compare page shows the same $649 figure[4] | $1,850.93 on prusa3d.com, Aug 2026; $1,925.00 with the Advanced Filtration bundle. Prusa's own comparison text on the CORE One+ page quotes "from $1,799", which does not match the live e-shop price[5][6] |
| Variants & sibling models — and how to tell them apart (spec-contamination risk) | Dual-nozzle machine: a main hotend with a permanent-magnet synchronous extruder motor and an auxiliary hotend with a plain stepper motor, so the two nozzles are not equivalent. Bambu publishes four different build volumes depending on which nozzle is used, and a shorter list of materials for the auxiliary nozzle. Physical dimensions (392x406x478 mm) are shared with the P2S but the X2D is 16.25 kg against the P2S's 14.9 kg[1][7] | Larger sibling of the CORE One+ (Gen 2): 300 x 300 x 330 mm against 250 x 220 x 270 mm, 60 C chamber against 55 C, 21.9 kg against 22.5 kg (the L is the lighter of the two despite being larger). A CORE One L to CORE One L+ upgrade kit exists, so "CORE One L" and "CORE One L+" are different revisions. A Critical Infrastructure Edition is also listed[2][6][5] |
| Market position: superseded? successor announced? | Current model, launched into the slot vacated by the discontinued X1-Carbon[4] | Not documented |
| Physical & Frame | ||
| Build volume X×Y×Z (mm) — advertised vs actually usable | Main nozzle 256 x 256 x 260 mm; auxiliary nozzle 235.5 x 256 x 256 mm; dual-nozzle printing 235.5 x 256 x 256 mm; total volume for two nozzles 256 x 256 x 260 mm. The sortable figure below is the main-nozzle volume[1] | 300 x 300 x 330 mm, which Prusa states as 29.7 litres[2] |
| Machine footprint (mm) & clearance needed (cable/spool overhang) | 392 x 406 x 478 mm[1] | 469 x 521 x 635 mm[2] |
| Net weight (kg) | 16.25 kg net[1] | 21.9 kg (48.3 lb)[2] |
| Frame construction & material | Plastic and steel chassis; plastic, glass and metal outer frame[1] | Not documented |
| Enclosure: open / enclosed; panel material; door/lid | Fully enclosed with a door sensor, active chamber heating to 65 C, and a G3 + H12 HEPA + granulated coconut-shell carbon filter stack with an external exhaust fan[1] | Fully enclosed with a chamber door-open sensor and an active convection heated chamber up to 60 C; advanced filtration is an optional add-on[2] |
| Passive chamber temperature reached (if enclosed; measured values preferred) | Active chamber heating, maximum 65 C (manufacturer figure)[1] | Active convection chamber heating, maximum 60 C (manufacturer figure)[2] |
| Kinematics & Motion Hardware | ||
| Kinematics (bedslinger i3 / CoreXY / other) | CoreXY - not stated in the spec sheet; Bambu groups the X2D with its enclosed CoreXY machines and publishes the same 20000 mm/s2 acceleration figure[1] | CoreXY - stated in Prusa's CORE One+ comparison table[6] |
| Stepper drivers (exact model e.g. TMC2209; UART/SPI; sensorless homing?) | Not documented | Trinamic drivers on the custom xBuddy mainboard (Prusa's CORE One L+ specification says "custom 32-bit xBuddy mainboard with STM32 processor & Trinamic drivers"; it does not give the driver part number)[2] |
| Speed & Acceleration | ||
| Max print speed (claimed, mm/s) | 1000 mm/s max toolhead speed (manufacturer claim); no independent measurement found[1] | Not documented |
| Max acceleration (claimed, mm/s²) | 20000 mm/s2 max toolhead acceleration (manufacturer claim)[1] | Not documented |
| Max volumetric flow claimed (mm³/s) | 40 mm3/s, measured by Bambu on a 250 mm round single-wall model in Bambu ABS at 280 C[1] | Not documented |
| Vibration Compensation / Input Shaping | ||
| Input shaping supported? Implementation (Klipper IS / Marlin ZV / proprietary) | Not documented | Input Shaper and Phase Stepping with an integrated accelerometer[2] |
| Extruder | ||
| Type (direct drive / bowden) & design name | Two direct-drive extruders: main extruder with hardened-steel gears driven by a Bambu high-precision permanent-magnet synchronous motor, auxiliary extruder with hardened-steel gears driven by a stepper motor[1] | Nextruder direct drive with a 10:1 planetary gear system; all-metal hotend with an aluminium heatsink and a tool-free quick-swap nozzle system[2] |
| Gear ratio & drive gear material | Not documented | 10:1 planetary gearbox[2] |
| Hotend & Nozzle | ||
| Hotend design (proprietary/standard; quick-swap mechanism?) | Dual hardened-steel nozzles; 0.4 mm included, 0.2/0.4/0.6/0.8 mm supported; built-in filament cutter[1] | Tool-free quick-swap nozzle system; Prusa brass high-flow CHT 0.4 mm pre-mounted plus an abrasive-resistant 0.4 mm nozzle in the box[2] |
| Max nozzle temp claimed AND firmware max temp limit (both values) | 300 C claimed max nozzle temperature[1] | 290 C claimed max nozzle temperature. The optional HT hotend that raises this to 400 C was announced for September 2026 availability, so it is not a shipping specification as of Aug 2026[2][3] |
| Heated Bed & Surface | ||
| Max bed temp claimed AND firmware limit | 120 C max heatbed temperature[1] | 120 C max heatbed temperature[2] |
| Bed surface (material, texture, coating), single/double-sided | Flexible steel plate, Textured PEI included; Smooth PEI, Cool Plate SuperTack and Engineering Plate supported[1] | Magnetic heatbed with removable dual-sided PEI spring-steel sheets; a satin powder-coated sheet is supplied[2] |
| Leveling & Z-Offset | ||
| Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe) | Not documented | High-precision load-cell sensor - fully automatic first-layer calibration and mesh bed levelling restricted to the print area[2] |
| Filament Handling & Detection | ||
| Filament runout sensor (type, location) | Yes - run-out sensor, tangle sensor and door sensor; odometry with AMS[1] | Two filament sensors, plus a chamber door-open sensor and five Semitec thermistors[2] |
| Cooling & Air Handling | ||
| Part-cooling fan(s): count, size, ducting design | Part-cooling fan, hotend cooling fan, main control board fan, chamber heat-circulation fan, auxiliary part-cooling fan and external exhaust fan, all closed-loop controlled[1] | Not documented |
| Electronics & Power | ||
| Mainboard model & MCU (exact chip markings if teardowns exist) | Motion controller dual-core Cortex-M4 plus single-core Cortex-M7; application processor quad-core ARM with a dedicated NPU (2 TOPS per the compare page)[1][8] | Custom 32-bit xBuddy mainboard with an STM32 processor[2] |
| Total rated power draw | High-voltage version 1600 W at 220 V, low-voltage version 1100 W at 110 V; steady state 250 W printing PLA and 550 W printing PC at 25 C ambient[1] | Standby 16 W, preheating about 630 W, average printing about 90 W on PLA and about 215 W on ASA (manufacturer figures)[2] |
| Firmware & Openness | ||
| Firmware base & current version (Klipper fork / Marlin fork / proprietary) | Closed-source proprietary firmware - not a Klipper or Marlin derivative, and no printer-firmware source is published. The bambulab GitHub organisation carries 11 repositories (Bambu Studio, wxWidgets/boost/ffmpeg forks, the wiki); none is printer firmware. Updates are delivered over the air via Bambu Studio / Bambu Handy[9] | Open-source Prusa Buddy firmware. The source tree (prusa3d/Prusa-Firmware-Buddy on GitHub) explicitly covers the Original Prusa MINI/MINI+, MK4, XL and CORE One and was last pushed to in August 2026. Updates are applied from a USB drive, through Prusa Connect or through the Prusa mobile app[10][11] |
| Connectivity, UI & Camera | ||
| Display: size, type, touch? | 5-inch 1280x720 touchscreen[1] | 3.5-inch 65k-colour touch screen (CORE One family)[6] |
| On-device UI capabilities (model preview, per-object controls, etc.) | Touchscreen plus mobile app and PC app[1] | On-device touch UI with Prusa Connect and Prusa mobile app remote control[6] |
| WiFi (band/standard), Ethernet, USB ports, SD/flash-drive | Dual-band Wi-Fi (802.11 a/b/g/n), built-in 8 GB eMMC and a USB port; Ethernet not available, no network kill switch, no 802.1X[1] | Ethernet, NFC receiver and Wi-Fi through a physically removable module, which Prusa offers for high-security offline installations[2] |
| Camera: built-in / optional? Resolution & framerate (verify — marketing often omits real fps) | Two cameras: live-view 1920x1080 and a toolhead camera at 1600x1200[1] | Not documented |
| Materials Support | ||
| Officially supported filament list | Main hotend: PLA, PETG, ABS, ASA, TPU, support materials, PET, PA, PC, PVA and carbon/glass-fibre reinforced PLA, PETG, ABS, ASA, PA6, PAHT, PPA, PET. Auxiliary hotend drops PPA-CF/GF and excludes PLA Aero; PLA Silk, PETG-CF, ASA-CF, PA6-CF, TPU for AMS and PA/PET support material are flagged "print with caution" on the auxiliary nozzle[1] | PLA, PETG, Flex, PVA, PC, PP, CPE, PVB, and with Advanced Filtration also ABS, ASA, HIPS and PA[2] |
| Safety | ||
| Thermal runaway protection (verify in firmware source if at all possible) | Not documented | Open-source firmware on the xBuddy platform, which carries hardware overcurrent protection cutting heater and heatbed power above 15 A[12][10] |
| Reliability, Support & Ecosystem | ||
| Warranty length & support reputation (evidence, not vibes) | 2-year limited warranty for consumers in the US, Canada, the EU, Switzerland, Norway and Iceland; 1 year in the rest of the world. Bambu Lab's own policy records the US/Canada term as a 2026 extension from one year to two[13] | 2-year warranty for consumers in the EU, Liechtenstein, Switzerland, Norway and Iceland; 1 year for EU enterprises and 1 year for the rest of the world, which includes the United States. A printer bought from a reseller or privately carries 1 year from the original delivery date and is handled by the reseller. Prusa advertises 24/7 chat and e-mail support in seven languages[14][11] |
Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.
Sources for this comparison
- Bambu Lab X2D Spec (PDF) store.bblcdn.com · 2026-08 · doc
- Prusa CORE One L+ product page (CORE One L+ Technical Specifications) prusa3d.com · 2026-08 · vendor
- Prusa blog - Better Prints, Easier Use: Prusa XL+, CORE One L+ and CORE One+ (Gen 2), Our Big Product Update (published 13 August 2026) blog.prusa3d.com · 2026-08 · doc
- Bambu Lab US Store - 3D Printers collection listing (base prices, Aug 2026) us.store.bambulab.com · 2026-08 · vendor
- Prusa 3D printers category listing with live e-shop prices, Aug 2026 prusa3d.com · 2026-08 · vendor
- Prusa CORE One+ (Gen 2) product page (Technical Parameters + CORE One+/MK4S/CORE One L comparison) prusa3d.com · 2026-08 · vendor
- Bambu Lab P2S Spec Sheet (PDF) store.bblcdn.com · 2026-08 · doc
- Bambu Lab - Compare all 3D printers (A2L / X2D / H2C columns) bambulab.com · 2026-08 · vendor
- GitHub - bambulab organisation repository list (11 repos, checked Aug 2026) github.com · 2026-08 · doc
- GitHub - prusa3d/Prusa-Firmware-Buddy (firmware for MINI, MK4, XL and CORE One) github.com · 2026-08 · doc
- Original Prusa MK4S 3D Printer product page (Technical Parameters + CORE One+/MK4S/XL comparison table) prusa3d.com · 2026-08 · vendor
- Prusa blog - Original Prusa MK4 is here (published 29 March 2023), including the MK4 specification table and launch prices blog.prusa3d.com · 2026-08 · doc
- Bambu Lab Warranty Policy bambulab.com · 2026-08 · vendor
- Prusa Knowledge Base - Warranty help.prusa3d.com · 2026-08 · doc