3D Printing Info

Printer comparison

Bambu Lab H2S vs ELEGOO Neptune 4 Plus

Compare hardware, build volume, printing specifications, dated prices and sources.

Bambu Lab H2S guideELEGOO Neptune 4 Plus guide

2 selected · all documented properties

Open these two in the interactive comparisonMore Bambu Lab H2S comparisonsMore ELEGOO Neptune 4 Plus comparisons
Bambu Lab H2S vs ELEGOO Neptune 4 Plus — documented properties and sources
PropertyBambu Lab H2SCOREXYELEGOO Neptune 4 PlusBEDSLINGER
Identity
BrandBambu LabELEGOO
ClassCOREXYBEDSLINGER
Identity & Market
Manufacturer & exact marketed model name (verify the exact product identity first)Bambu Lab H2S; spec sheet header "H2S & H2S Laser Edition Spec Sheet"[1]ELEGOO Neptune 4 Plus[2]
Release date (announcement and actual shipping)Not documentedListed on the ELEGOO US store from 20 September 2023 (Shopify publish date), the same date as the Neptune 4 Max[3][4]
Street price (USD; dated snapshot per entry)From $1,199.00 on the Bambu Lab US store, Aug 2026, against a stated typical price of $1,249.00[5]$309.00 on us.elegoo.com, Aug 2026, against a compare-at price of $425.00. Only a Ribbon-Cable printhead variant is listed for the Plus, unlike the Neptune 4 and 4 Max which also offer a Type-C version[3][6][4]
Variants & sibling models — and how to tell them apart (spec-contamination risk)Single-nozzle machine sharing the H2 body. H2S and H2S Laser Edition are covered by one spec sheet: the Laser Edition adds laser safety windows, the air-assist pump and the 3264x2448 BirdsEye camera, and a plain H2S can be upgraded with a Laser Upgrade Kit. Against the dual-nozzle H2D in the same 492x514x626 mm shell: 30 kg vs 31 kg, 340x320x340 mm single-nozzle volume vs 325x320x325 mm[1][7]Middle model of the Neptune 4 family. Against the base Neptune 4: bigger (320 x 320 x 385 mm), but a lower bed ceiling (100 C rather than 110 C) and much lower acceleration (12000 rather than 20000 mm/s2). Against the Max: smaller and lighter (14.4 kg against 18.1 kg) but with a higher bed ceiling (100 C against 85 C) and higher acceleration (12000 against 8000). Its Z drive is 2 lead screws with 2 tie rods, where the Centauri machines use 3 lead screws[2][8][9][10]
Physical & Frame
Build volume X×Y×Z (mm) — advertised vs actually usable340 x 320 x 340 mm (manufacturer figure)[1]320 x 320 x 385 mm; printing platform 330 x 330 mm[2]
Machine footprint (mm) & clearance needed (cable/spool overhang)492 x 514 x 626 mm - the same body as the H2D and H2C[1]533 x 517 x 638 mm; ELEGOO also publishes a maximum size for machine activity of 578 x 750 x 860 mm including rack and tray, so allow 750 mm of depth[2]
Net weight (kg)30 kg net[1]14.4 kg net, 16.65 kg gross[2]
Frame construction & materialAluminium and steel chassis and shell[1]CNC-machined aluminium extrusion frame (Neptune 4 family)[8]
Enclosure: open / enclosed; panel material; door/lidFully enclosed with a door sensor; active chamber heating to 65 C, chamber exhaust and heat-circulation fans, G3 + H12 + coconut-shell carbon filtration[1]Open frame, no enclosure[2]
Passive chamber temperature reached (if enclosed; measured values preferred)Active chamber heating, maximum 65 C (manufacturer figure)[1]Not documented
Kinematics & Motion Hardware
Kinematics (bedslinger i3 / CoreXY / other)CoreXY - not named in the spec sheet; grouped by Bambu with the H2 enclosed CoreXY machines at 20000 mm/s2[1]Cartesian i3 bed-slinger[2]
Z-axis: leadscrew count & type, sync mechanism, anti-backlashNot documentedTwo lead screws with two tie rods[2]
Stepper drivers (exact model e.g. TMC2209; UART/SPI; sensorless homing?)Not documented"Silent Drive (All Axes)" is all ELEGOO publishes; the driver part number is not given on the product page[2]
Speed & Acceleration
Max print speed (claimed, mm/s)1000 mm/s max toolhead speed (manufacturer claim); no independent measurement found[1]30-500 mm/s printing speed, with 250 mm/s given by ELEGOO as the recommended figure - the 500 mm/s number is a ceiling, not a working speed[2]
Recommended/typical print speedNot documented250 mm/s recommended printing speed (manufacturer figure)[2]
Max acceleration (claimed, mm/s²)20000 mm/s2 max toolhead acceleration (manufacturer claim)[1]12000 mm/s2 maximum acceleration; default acceleration 5000 mm/s2[2]
Max volumetric flow claimed (mm³/s)40 mm3/s standard-flow hotend, 65 mm3/s optional high-flow hotend; Bambu's test is a 250 mm round single-wall model in Bambu ABS at 280 C[1]Not documented
Extruder
Type (direct drive / bowden) & design nameDirect drive with hardened-steel gears and a Bambu high-precision permanent-magnet synchronous extruder motor; built-in filament cutter[1]Dual-gear direct extruder with 2 fans (the Centauri machines use a 1-fan version)[2][10]
Hotend & Nozzle
Hotend design (proprietary/standard; quick-swap mechanism?)All-metal hotend, hardened-steel nozzle, 0.4 mm included, 0.2/0.4/0.6/0.8 mm supported; optional high-flow hotend[1]Brass nozzle, 0.4 mm, with a titanium-alloy heat break[2]
Max nozzle temp claimed AND firmware max temp limit (both values)350 C claimed max nozzle temperature[1]300 C claimed max nozzle temperature[2]
Heated Bed & Surface
Max bed temp claimed AND firmware limit120 C max heatbed temperature[1]100 C max heated bed temperature at 25 C ambient[2]
Bed surface (material, texture, coating), single/double-sidedTextured PEI plate and Smooth PEI plate supported[1]PEI spring steel sheet; ELEGOO notes it is now upgraded to a dual-sided textured PEI + PLA-specific surface[2]
Leveling & Z-Offset
Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe)Not documentedManual levelling combined with 121-point auto-levelling[2]
Filament Handling & Detection
Filament runout sensor (type, location)Yes - run-out sensor, tangle sensor and door sensor; odometry with AMS[1]Filament run-out sensor and power-loss recovery; no camera, no clog detection, no auto filament unloading[2]
Cooling & Air Handling
Part-cooling fan(s): count, size, ducting designPart-cooling fan, hotend cooling fan, main control board fan, chamber exhaust fan, chamber heat-circulation fan and auxiliary part-cooling fan, all closed-loop controlled[1]Not documented
Electronics & Power
Mainboard model & MCU (exact chip markings if teardowns exist)Not documentedELEGOO describes it only as a "Klipper High-Speed Quiet Motherboard" - no board model or MCU is published[2]
Total rated power draw100-120 VAC / 200-240 VAC 50/60 Hz; 2050 W at 220 V, 1170 W at 110 V[1]320 W rated power; 24 V output; 110-120 V / 220-240 V input[2]
Firmware & Openness
Firmware base & current version (Klipper fork / Marlin fork / proprietary)Closed-source proprietary firmware - not a Klipper or Marlin derivative, and no printer-firmware source is published. The bambulab GitHub organisation carries 11 repositories (Bambu Studio, wxWidgets/boost/ffmpeg forks, the wiki); none is printer firmware. Updates are delivered over the air via Bambu Studio / Bambu Handy[11]Klipper (ELEGOO names the system "Klipper" outright for the Neptune 4 Plus, rather than the ELEGOO OS branding used on the Centauri machines)[2][10]
Connectivity, UI & Camera
Display: size, type, touch?5-inch 720x1280 touchscreen[1]4.3-inch colour capacitive touch screen[2]
On-device UI capabilities (model preview, per-object controls, etc.)Touchscreen plus mobile app and PC app[1]Colour capacitive touch UI; ElegooSlicer is recommended, with Orca and Cura also supported[2]
WiFi (band/standard), Ethernet, USB ports, SD/flash-driveBuilt-in 8 GB eMMC and a USB port; touchscreen, app and PC control interfaces[1]USB, LAN and Wi-Fi[2]
Camera: built-in / optional? Resolution & framerate (verify — marketing often omits real fps)Live-view camera 1920x1080 and toolhead camera 1600x1200; the 3264x2448 BirdsEye camera is fitted only on the Laser Edition[1]Not documented
Materials Support
Officially supported filament listPLA, PETG, TPU, PVA, BVOH, ABS, ASA, PC, PA, PET, PPS, plus carbon/glass-fibre reinforced PLA, PETG, PA, PET, PC, ABS, ASA, PPA and PPS[1]PLA, TPU, PETG, ABS, ASA, Nylon[2]
Noise & Power Consumption
Noise: claimed dB and independently measured dB (distance/method)Not documentedOperating sound is published as 65 dB or less - a manufacturer figure with no measuring distance or method given, so it is not comparable with a reviewer's dB reading[2]
Reliability, Support & Ecosystem
Warranty length & support reputation (evidence, not vibes)2-year limited warranty for consumers in the US, Canada, the EU, Switzerland, Norway and Iceland; 1 year in the rest of the world. Bambu Lab's own policy records the US/Canada term as a 2026 extension from one year to two[12]12 months on brand-new machines and parts, but ELEGOO's own table excludes a long list of parts from that: PEI plate / build plate / nozzle kit / PTFE tube / heater / thermistor / hot end / packaging / manual / tools carry no warranty at all, and the extruder, extruder kit and printhead kit get 6 months. Certified pre-owned machines carry no warranty[13]

Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.

Sources for this comparison

  1. Bambu Lab H2S & H2S Laser Edition Spec Sheet (PDF) store.bblcdn.com · 2026-08 · doc
  2. ELEGOO Neptune 4 Plus product page (full specification table) us.elegoo.com · 2026-08 · vendor
  3. ELEGOO Neptune 4 Plus Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
  4. ELEGOO Neptune 4 Max Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
  5. Bambu Lab US Store - 3D Printers collection listing (base prices, Aug 2026) us.store.bambulab.com · 2026-08 · vendor
  6. ELEGOO Neptune 4 Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
  7. Bambu Lab H2D - Technical Specifications bambulab.com · 2026-08 · vendor
  8. ELEGOO Neptune 4 product page (Specification table) us.elegoo.com · 2026-08 · vendor
  9. ELEGOO Neptune 4 Max product page (Specification table) us.elegoo.com · 2026-08 · vendor
  10. ELEGOO Centauri Carbon product page (full specification table) us.elegoo.com · 2026-08 · vendor
  11. GitHub - bambulab organisation repository list (11 repos, checked Aug 2026) github.com · 2026-08 · doc
  12. Bambu Lab Warranty Policy bambulab.com · 2026-08 · vendor
  13. ELEGOO Refund & Warranty policy (warranty period table) us.elegoo.com · 2026-08 · vendor