3D Printing InfoPrinter comparison
Bambu Lab A2L vs ELEGOO Neptune 4 Plus
Compare hardware, build volume, printing specifications, dated prices and sources.
2 selected · all documented properties
Open these two in the interactive comparisonMore Bambu Lab A2L comparisonsMore ELEGOO Neptune 4 Plus comparisons
| Property | Bambu Lab A2LBEDSLINGER | ELEGOO Neptune 4 PlusBEDSLINGER |
|---|---|---|
| Identity | ||
| Brand | Bambu Lab | ELEGOO |
| Class | BEDSLINGER | BEDSLINGER |
| Identity & Market | ||
| Manufacturer & exact marketed model name (verify the exact product identity first) | Bambu Lab A2L[1] | ELEGOO Neptune 4 Plus[2] |
| Release date (announcement and actual shipping) | Pre-orders opened 1 June 2026 (Tom's Hardware spec box); Tom's Hardware review published 27 June 2026[3] | Listed on the ELEGOO US store from 20 September 2023 (Shopify publish date), the same date as the Neptune 4 Max[4][5] |
| Launch MSRP (USD) | $469 standalone, $569 Combo at launch[3] | Not documented |
| Street price (USD; dated snapshot per entry) | From $469.00 on the Bambu Lab US store, Aug 2026[6] | $309.00 on us.elegoo.com, Aug 2026, against a compare-at price of $425.00. Only a Ribbon-Cable printhead variant is listed for the Plus, unlike the Neptune 4 and 4 Max which also offer a Type-C version[4][7][5] |
| Variants & sibling models — and how to tell them apart (spec-contamination risk) | Standalone and Combo (with AMS lite) SKUs, and an optional cutting/drawing module (blade cutter and pen plotter, 300x300 mm cutting area) that is a separate attachment, not a printer variant. Do not carry A1 or A1 mini figures across: the A2L is a different, much larger machine at 12.8 kg[1][3] | Middle model of the Neptune 4 family. Against the base Neptune 4: bigger (320 x 320 x 385 mm), but a lower bed ceiling (100 C rather than 110 C) and much lower acceleration (12000 rather than 20000 mm/s2). Against the Max: smaller and lighter (14.4 kg against 18.1 kg) but with a higher bed ceiling (100 C against 85 C) and higher acceleration (12000 against 8000). Its Z drive is 2 lead screws with 2 tie rods, where the Centauri machines use 3 lead screws[2][8][9][10] |
| Physical & Frame | ||
| Build volume X×Y×Z (mm) — advertised vs actually usable | 330 x 320 x 325 mm (manufacturer figure)[1] | 320 x 320 x 385 mm; printing platform 330 x 330 mm[2] |
| Machine footprint (mm) & clearance needed (cable/spool overhang) | 544 x 529 x 505 mm[1] | 533 x 517 x 638 mm; ELEGOO also publishes a maximum size for machine activity of 578 x 750 x 860 mm including rack and tray, so allow 750 mm of depth[2] |
| Net weight (kg) | 12.8 kg net[1] | 14.4 kg net, 16.65 kg gross[2] |
| Frame construction & material | Aluminium and steel chassis with a plastic outer frame; Tom's Hardware describes a triangular gantry frame the base drops into[1] | CNC-machined aluminium extrusion frame (Neptune 4 family)[8] |
| Enclosure: open / enclosed; panel material; door/lid | Open frame, no enclosure[1] | Open frame, no enclosure[2] |
| Kinematics & Motion Hardware | ||
| Kinematics (bedslinger i3 / CoreXY / other) | Cartesian bed-slinger - Tom's Hardware's assembly description has the heatbed bolting to a Y-carriage inside the gantry frame[3] | Cartesian i3 bed-slinger[2] |
| Z-axis: leadscrew count & type, sync mechanism, anti-backlash | Not published in the spec sheet; no teardown source found that documents the Z drive[1] | Two lead screws with two tie rods[2] |
| Stepper drivers (exact model e.g. TMC2209; UART/SPI; sensorless homing?) | Not documented | "Silent Drive (All Axes)" is all ELEGOO publishes; the driver part number is not given on the product page[2] |
| Speed & Acceleration | ||
| Max print speed (claimed, mm/s) | 500 mm/s max toolhead speed (manufacturer claim)[1] | 30-500 mm/s printing speed, with 250 mm/s given by ELEGOO as the recommended figure - the 500 mm/s number is a ceiling, not a working speed[2] |
| Recommended/typical print speed | Not documented | 250 mm/s recommended printing speed (manufacturer figure)[2] |
| Max acceleration (claimed, mm/s²) | 10 m/s2 = 10000 mm/s2 max toolhead acceleration (manufacturer claim)[1] | 12000 mm/s2 maximum acceleration; default acceleration 5000 mm/s2[2] |
| Max volumetric flow claimed (mm³/s) | 28 mm3/s claimed, measured by Bambu on a 150 mm round single-wall model in Bambu PLA Basic at 220 C - note this test uses PLA, unlike the ABS-based figures Bambu quotes for its enclosed machines, so it is not directly comparable[1] | Not documented |
| Extruder | ||
| Type (direct drive / bowden) & design name | Direct drive with a servo extruder motor and hardened-steel extruder gears; built-in filament cutter[1] | Dual-gear direct extruder with 2 fans (the Centauri machines use a 1-fan version)[2][10] |
| Hotend & Nozzle | ||
| Hotend design (proprietary/standard; quick-swap mechanism?) | Stainless-steel nozzle; 0.2/0.4/0.6/0.8 mm supported. Bambu's A2L sheet does not state whether the hotend is all-metal[1] | Brass nozzle, 0.4 mm, with a titanium-alloy heat break[2] |
| Max nozzle temp claimed AND firmware max temp limit (both values) | 300 C claimed max nozzle temperature[1] | 300 C claimed max nozzle temperature[2] |
| Heated Bed & Surface | ||
| Max bed temp claimed AND firmware limit | 80 C max heatbed temperature[1] | 100 C max heated bed temperature at 25 C ambient[2] |
| Bed surface (material, texture, coating), single/double-sided | Textured PEI plate included; Engineering Plate and Cool Plate SuperTack also supported[1] | PEI spring steel sheet; ELEGOO notes it is now upgraded to a dual-sided textured PEI + PLA-specific surface[2] |
| Leveling & Z-Offset | ||
| Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe) | Automatic bed levelling with automatic Z: Tom's Hardware confirms the nozzle is used as the probe and the machine can re-check level before each print[3] | Manual levelling combined with 121-point auto-levelling[2] |
| Filament Handling & Detection | ||
| Filament runout sensor (type, location) | Yes - run-out sensor, filament odometry, tangle sensor and clumping detection[1] | Filament run-out sensor and power-loss recovery; no camera, no clog detection, no auto filament unloading[2] |
| Cooling & Air Handling | ||
| Part-cooling fan(s): count, size, ducting design | Part-cooling fan and hotend cooling fan, both closed-loop controlled. No auxiliary part-cooling fan and no chamber fan[1] | Not documented |
| Electronics & Power | ||
| Mainboard model & MCU (exact chip markings if teardowns exist) | Not documented | ELEGOO describes it only as a "Klipper High-Speed Quiet Motherboard" - no board model or MCU is published[2] |
| Total rated power draw | Not documented | 320 W rated power; 24 V output; 110-120 V / 220-240 V input[2] |
| Firmware & Openness | ||
| Firmware base & current version (Klipper fork / Marlin fork / proprietary) | Closed-source proprietary firmware - not a Klipper or Marlin derivative, and no printer-firmware source is published. The bambulab GitHub organisation carries 11 repositories (Bambu Studio, wxWidgets/boost/ffmpeg forks, the wiki); none is printer firmware. Updates are delivered over the air via Bambu Studio / Bambu Handy[11] | Klipper (ELEGOO names the system "Klipper" outright for the Neptune 4 Plus, rather than the ELEGOO OS branding used on the Centauri machines)[2][10] |
| Connectivity, UI & Camera | ||
| Display: size, type, touch? | 3.5-inch 240x320 touchscreen[1] | 4.3-inch colour capacitive touch screen[2] |
| On-device UI capabilities (model preview, per-object controls, etc.) | Touchscreen plus mobile app and PC app[1] | Colour capacitive touch UI; ElegooSlicer is recommended, with Orca and Cura also supported[2] |
| WiFi (band/standard), Ethernet, USB ports, SD/flash-drive | 2.4 GHz Wi-Fi only (802.11 b/g/n), Bambu-Bus, microSD card. Ethernet not available[1] | USB, LAN and Wi-Fi[2] |
| Camera: built-in / optional? Resolution & framerate (verify — marketing often omits real fps) | Built-in low-frame-rate camera, up to 1080p, timelapse supported[1] | Not documented |
| Materials Support | ||
| Officially supported filament list | Suitable: PLA, PETG, TPU, PVA. PLA-CF and PETG-CF suitable only after fitting a hardened-steel nozzle. ABS, ASA, PA, PC and PET are listed as not recommended on the compare page[1][12] | PLA, TPU, PETG, ABS, ASA, Nylon[2] |
| Noise & Power Consumption | ||
| Noise: claimed dB and independently measured dB (distance/method) | Not documented | Operating sound is published as 65 dB or less - a manufacturer figure with no measuring distance or method given, so it is not comparable with a reviewer's dB reading[2] |
| Reliability, Support & Ecosystem | ||
| Warranty length & support reputation (evidence, not vibes) | 2-year limited warranty for consumers in the US, Canada, the EU, Switzerland, Norway and Iceland; 1 year in the rest of the world. Bambu Lab's own policy records the US/Canada term as a 2026 extension from one year to two[13] | 12 months on brand-new machines and parts, but ELEGOO's own table excludes a long list of parts from that: PEI plate / build plate / nozzle kit / PTFE tube / heater / thermistor / hot end / packaging / manual / tools carry no warranty at all, and the extruder, extruder kit and printhead kit get 6 months. Certified pre-owned machines carry no warranty[14] |
| Independently Measured Performance | ||
| Review scores from major outlets (list outlet + score + date) | Tom's Hardware: Editor's Choice, rating 4.5 out of 5 in the page's structured data (27 June 2026)[3] | Not documented |
Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.
Sources for this comparison
- Bambu Lab A2L Spec Sheet (PDF) store.bblcdn.com · 2026-08 · doc
- ELEGOO Neptune 4 Plus product page (full specification table) us.elegoo.com · 2026-08 · vendor
- Tom's Hardware - Bambu Lab A2L 3D printer review, 27 June 2026 tomshardware.com · 2026-08 · review
- ELEGOO Neptune 4 Plus Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Max Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
- Bambu Lab US Store - 3D Printers collection listing (base prices, Aug 2026) us.store.bambulab.com · 2026-08 · vendor
- ELEGOO Neptune 4 Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 product page (Specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Max product page (Specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Centauri Carbon product page (full specification table) us.elegoo.com · 2026-08 · vendor
- GitHub - bambulab organisation repository list (11 repos, checked Aug 2026) github.com · 2026-08 · doc
- Bambu Lab - Compare all 3D printers (A2L / X2D / H2C columns) bambulab.com · 2026-08 · vendor
- Bambu Lab Warranty Policy bambulab.com · 2026-08 · vendor
- ELEGOO Refund & Warranty policy (warranty period table) us.elegoo.com · 2026-08 · vendor