3D Printing Info

Printer comparison

Bambu Lab A1 vs Prusa CORE One+ (Gen 2) INDX

Compare hardware, build volume, printing specifications, dated prices and sources.

Bambu Lab A1 guidePrusa CORE One+ (Gen 2) INDX guide

2 selected · all documented properties

Open these two in the interactive comparisonMore Bambu Lab A1 comparisonsMore Prusa CORE One+ (Gen 2) INDX comparisons
Bambu Lab A1 vs Prusa CORE One+ (Gen 2) INDX — documented properties and sources
PropertyBambu Lab A1BEDSLINGERPrusa CORE One+ (Gen 2) INDXTOOLCHANGER
Identity
BrandBambu LabPrusa Research
ClassBEDSLINGERTOOLCHANGER
Identity & Market
Manufacturer & exact marketed model name (verify the exact product identity first)Bambu Lab A1. Store title: "Bambu Lab A1 3D Printer"; spec page header "Bambu Lab A1 - Technical Specifications"[1]Prusa CORE One+ (Gen 2) INDX, listed as "INDX 4-Tool" and "INDX 8-Tool" variants and as an "INDX 8-Tool Assembly kit"[2][3]
Release date (announcement and actual shipping)Announced and first shipped in the northern autumn/winter of 2023. Bambu Lab's own recall notice states A1 units were supplied from 1 December 2023; Tom's Hardware published its A1 review on 14 December 2023, so retail units were in reviewers' hands by then[4][5]Announced as shipping on 20 August 2026 ("INDX, Shipping Has Started, Complete Printers Open for Orders"). Prusa's own front page in Aug 2026 announces "Prusa CORE One+ (Gen 2) INDX, Shipping Has Started, Complete Printers Open for Orders", with the assembled 8-tool machine quoted as shipping from 15 October and the kit from 29 October[6][2]
Street price (USD; dated snapshot per entry)From $299.00 (base A1) on the Bambu Lab US store, Aug 2026, during an advertised Back-to-School sale; the A1 product page shows $399.00 with the A1 Combo (A1 + AMS lite) swatch selected[7][8]$1,850.93 for the INDX 4-Tool and $2,082.41 for the INDX 8-Tool on prusa3d.com, Aug 2026; the 8-Tool assembly kit is $1,804.63. Camera and filtration bundles run to $2,152.78[2][3]
Variants & sibling models — and how to tell them apart (spec-contamination risk)Two SKUs on one product page: A1 (printer only) and A1 Combo (adds the AMS lite four-spool unit); the printer hardware is identical. Do NOT confuse with the A1 mini (180 mm cube, single Z leadscrew, 80 C bed, 2.4-in screen) or the newer A2L (330x320x325 mm). Contamination example found in the wild: Tom's Hardware's A1 review spec box prints a 2.4-inch screen and a 385x410x430 mm footprint (both A1 mini figures) and titles a section "Included in the box: Bambu Lab A1 Mini", while Bambu's own A1 spec sheet says 3.5-inch screen and 465x410x430 mm[1][5][8]INDX is a multi-tool option on the CORE One+ (Gen 2) product page rather than a separate printer, sold in 4-tool and 8-tool configurations, plus a CORE One/+ INDX conversion kit for existing machines. All of the body, hotend, bed and electronics figures below come from that shared CORE One+ (Gen 2) page and were not published separately for the INDX machine, so treat them as platform figures. Prusa also sells the unrelated MMU3, which multiplexes five filaments through one nozzle[3][2]
Market position: superseded? successor announced?Still sold new in Aug 2026 alongside the newer and larger A2L ($469 base), which Bambu positions as the mega-size A-series machine[7][9]Not documented
Physical & Frame
Build volume X×Y×Z (mm) — advertised vs actually usable256 x 256 x 256 mm (manufacturer figure)[1]250 x 220 x 270 mm - the CORE One+ (Gen 2) figure from the shared product page; Prusa does not publish a separate INDX build volume[3]
Machine footprint (mm) & clearance needed (cable/spool overhang)465 x 410 x 430 mm per Bambu's own tech-spec sheet. Tom's Hardware's spec box prints 385 x 410 x 430 mm for the same machine - that is the A1 mini's width, treat Bambu's figure as authoritative. Add clearance behind for Y-axis bed travel and above for the spool[1][5]415 x 444 x 555 mm - shared CORE One+ (Gen 2) figure[3]
Net weight (kg)8.3 kg net[1]Not documented
Frame construction & materialSteel plus extruded aluminium chassis; Bambu markets all-metal rails and a cover-protected drive system[1][10]Not documented
Enclosure: open / enclosed; panel material; door/lidOpen frame, no enclosure or door; no official enclosure is sold for the A1[1]Fully enclosed with active chamber heating up to 55 C (shared CORE One+ platform)[3]
Kinematics & Motion Hardware
Kinematics (bedslinger i3 / CoreXY / other)Cartesian bed-slinger: toolhead moves in X on the gantry beam, heatbed moves in Y, gantry moves in Z. Bambu's own wiki calls it a Cartesian coordinate motion system; Bambu's marketing page describes it as a "Bed Slinger with CoreXY Speed", which is a comparison, not a kinematic claim[11][10]CoreXY with a multi-tool head-changing system (INDX); Prusa's comparison table gives CoreXY for the CORE One family[3]
X-axis guide type (rods / linear rails / V-wheels; size)Linear rail: "a high-precision linear rail and a beam", toolhead on a linear guide slider (Bambu wiki). Rail size not published[11]Not documented
Y-axis guide typeLinear rail: heatbed mounted on a guide-rail slider, belt-driven in Y[11]Not documented
Z-axis: leadscrew count & type, sync mechanism, anti-backlashDual linear rods plus dual leadscrews with nuts, both leadscrews driven from one stepper through a synchronous belt with a quick tensioner and a tension-detection algorithm[11]Not documented
Belts (type, width, e.g. Gates?)Three adjustable belt tensioners (X, Y, Z); a Belt Tension Monitor watches tension and reports out-of-range belts[11]Not documented
Stepper drivers (exact model e.g. TMC2209; UART/SPI; sensorless homing?)Not published. Bambu's wiki says only that the mainboard "incorporates stepper motor drivers"; no driver part number is given and no teardown source was found that names one[11]Not documented
Speed & Acceleration
Max print speed (claimed, mm/s)500 mm/s max toolhead speed (manufacturer claim); no independent measurement found[1]Not documented
Max acceleration (claimed, mm/s²)10000 mm/s2 max toolhead acceleration (manufacturer claim). Tom's Hardware notes the moving-bed mass is why the A1 does not reach the P1S/X1 20000 mm/s2 figure[1][5]Not documented
Max volumetric flow claimed (mm³/s)28 mm3/s claimed, measured by Bambu on a 150x150 mm single-wall model in Bambu ABS at 280 C[1]Not documented
Extruder
Type (direct drive / bowden) & design nameDirect drive, hardened-steel extruder gears, integrated in the toolhead with a filament cutter and filament hub[1][11]Nextruder direct drive, 10:1 planetary gearbox (shared platform)[3]
Hotend & Nozzle
Hotend design (proprietary/standard; quick-swap mechanism?)All-metal integrated hotend (nozzle and heatsink combined in one unit) with a quick-swap clip - Bambu markets it as popping in and out with one clip. Stainless-steel nozzle, 0.4 mm included, 0.2/0.6/0.8 mm optional[1][10][11]Not documented
Max nozzle temp claimed AND firmware max temp limit (both values)300 C claimed max hot-end temperature; firmware limit not published[1]290 C claimed max nozzle temperature, 400 C with the optional HT hotend (shared platform)[3]
Heated Bed & Surface
Max bed temp claimed AND firmware limit100 C max build-plate temperature (both the spec sheet and the wiki give 100 C)[1][11]120 C max heatbed temperature (shared platform)[3]
Bed surface (material, texture, coating), single/double-sidedTextured PEI plate included; Bambu Cool Plate, High Temperature Plate and Dual-Texture PEI Plate also compatible[1]Not documented
Leveling & Z-Offset
Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe)Nozzle-touch probing: the hotend carries an eddy-current sensor that detects nozzle-to-bed contact, giving both automatic bed mesh and automatic Z-offset with no paper method. The same eddy-current sensor doubles as the Y-axis resonance sensor[11][5]Load-cell sensor, fully automatic first-layer calibration (shared platform)[3]
Filament Handling & Detection
Filament runout sensor (type, location)Yes - filament run-out sensor, plus filament odometry and a filament-tangle sensor. The tangle sensor is a Hall sensor reading a magnet in the toolhead filament hub: excessive feed resistance pulls the hub down, moving the magnet toward the sensor[1][11]Filament sensors fitted (two on the CORE One+ platform)[3]
Multi-material/multi-color capability or official upgrade pathOptional AMS lite (four spools, sold in the A1 Combo); connecting the enclosed-printer AMS / AMS 2 Pro / AMS HT to an A1 additionally requires an AMS HUB accessory (SA013)[8]INDX gives up to eight filaments; the alternative MMU3 handles five through a single nozzle[3]
Cooling & Air Handling
Part-cooling fan(s): count, size, ducting designOne custom 5015 centrifugal part-cooling fan with two opposing air outlets aimed at the nozzle; closed-loop (RPM-feedback) control[1][11]Not documented
Electronics & Power
Mainboard model & MCU (exact chip markings if teardowns exist)Single mainboard carrying a low-power dual-core SoC (with Wi-Fi and Bluetooth basebands and RF), a dual-core MCU and a single-core MCU, plus the stepper drivers. Bambu's spec sheet names the motion controller as a dual-core Cortex-M4. Exact chip markings not published[1]Custom 32-bit xBuddy board with STM32 (shared platform)[3]
Total rated power draw100-240 VAC 50/60 Hz; max power 1300 W at 220 V, 350 W at 110 V. Bed heater wattage is not published separately[1]Not documented
Firmware & Openness
Firmware base & current version (Klipper fork / Marlin fork / proprietary)Closed-source proprietary firmware - not a Klipper or Marlin derivative, and no printer-firmware source is published. The bambulab GitHub organisation carries 11 repositories (Bambu Studio, wxWidgets/boost/ffmpeg forks, the wiki); none is printer firmware. Updates are delivered over the air via Bambu Studio / Bambu Handy[12]Open-source Prusa Buddy firmware. The source tree (prusa3d/Prusa-Firmware-Buddy on GitHub) explicitly covers the Original Prusa MINI/MINI+, MK4, XL and CORE One and was last pushed to in August 2026. Updates are applied from a USB drive, through Prusa Connect or through the Prusa mobile app[13][14]
Connectivity, UI & Camera
Display: size, type, touch?3.5-inch 320x240 IPS touchscreen[1]3.5-inch 65k-colour touch screen (shared platform)[3]
On-device UI capabilities (model preview, per-object controls, etc.)Touchscreen UI plus Bambu Handy mobile app and Bambu Studio PC application; Bambu describes the on-device UI as a simplified guided touchscreen system[1][10]Not documented
WiFi (band/standard), Ethernet, USB ports, SD/flash-driveWi-Fi 2.4 GHz only (IEEE 802.11 b/g/n, 2412-2472 MHz), Bambu-Bus for the AMS lite, microSD card slot. No Ethernet, no USB host port[1]Ethernet and Wi-Fi, USB drive (shared platform)[3]
Camera: built-in / optional? Resolution & framerate (verify — marketing often omits real fps)Built-in low-rate monitoring camera, up to 1080p, timelapse supported; Bambu's marketing calls out a physical lens cover. Frame rate is not stated for the A1 (the P1 series camera is specified at 0.5 fps)[1][10]Not documented
Calibration Routines & QoL
Assembly level & time from unbox to first printAbout 95% pre-assembled; a handful of screws attach the gantry to the base, then the filament wiper and spool holder[5]Not documented
Materials Support
Officially supported filament listIdeal: PLA, PETG, TPU, PVA. Not recommended: ABS, ASA, PC, PA, PET, carbon/glass-fibre reinforced polymers - the machine is open-frame and the bed stops at 100 C[1]PLA, PETG, Flex, PVA, PC, PP, CPE, PVB; ABS, ASA, HIPS and PA as advanced materials in the heated chamber (shared platform)[3]
Safety
Known safety incidents / recalls / fire reports (with sources)Recalled in the US in cooperation with the CPSC: A1 units sold before 30 January 2024 (serial numbers with 'A' as the sixth digit) could suffer heatbed cable damage leading to a short circuit, electric shock or fire. 19 reports of damaged cables, one with observed sparking, no injuries. Remedy was refund plus $80 voucher, or heatbed+cable replacement by a trained technician plus $120 voucher. Current production ships a Kevlar-reinforced heatbed cable with thicker insulation and extended strain relief[4][8]Not documented
Noise & Power Consumption
Noise: claimed dB and independently measured dB (distance/method)Manufacturer claim only: bambulab.com states "Silent Mode Under 48 dB" with active motor noise cancelling; the US store page for both the A1 and the A1 mini carries identical copy claiming "49dB Whisper-Quiet Operation". No microphone-based independent measurement with a stated distance was found; Tom's Hardware only says it is "much more quiet than the current crop of speed freak machines"[10][8][5]Not documented
Reliability, Support & Ecosystem
Warranty length & support reputation (evidence, not vibes)2-year limited warranty for consumers in the US, Canada, the EU, Switzerland, Norway and Iceland; 1 year in the rest of the world. Bambu Lab's own policy records the US/Canada term as a 2026 extension from one year to two[15]2-year warranty for consumers in the EU, Liechtenstein, Switzerland, Norway and Iceland; 1 year for EU enterprises and 1 year for the rest of the world, which includes the United States. A printer bought from a reseller or privately carries 1 year from the original delivery date and is handled by the reseller. Prusa advertises 24/7 chat and e-mail support in seven languages[16][14]
Independently Measured Performance
Review scores from major outlets (list outlet + score + date)Tom's Hardware: Editor's Choice, rating 4.5 out of 5 in the page's structured data (14 December 2023)[5]Not documented

Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.

Sources for this comparison

  1. Bambu Lab A1 - Technical Specifications bambulab.com · 2026-08 · vendor
  2. Prusa 3D printers category listing with live e-shop prices, Aug 2026 prusa3d.com · 2026-08 · vendor
  3. Prusa CORE One+ (Gen 2) product page (Technical Parameters + CORE One+/MK4S/CORE One L comparison) prusa3d.com · 2026-08 · vendor
  4. Bambu Lab - Bambu Lab Recalls A1 3D Printers in the US bambulab.com · 2026-08 · vendor
  5. Tom's Hardware - Bambu Lab A1 Review, Denise Bertacchi, 14 December 2023 tomshardware.com · 2026-08 · review
  6. Prusa blog - Prusa CORE One+ (Gen 2) INDX, Shipping Has Started, Complete Printers Open for Orders (published 20 August 2026) blog.prusa3d.com · 2026-08 · doc
  7. Bambu Lab US Store - 3D Printers collection listing (base prices, Aug 2026) us.store.bambulab.com · 2026-08 · vendor
  8. Bambu Lab A1 store page (A1 / A1 Combo variants) us.store.bambulab.com · 2026-08 · vendor
  9. Bambu Lab - Compare all 3D printers (A2L / X2D / H2C columns) bambulab.com · 2026-08 · vendor
  10. Bambu Lab A1 product page bambulab.com · 2026-08 · vendor
  11. Bambu Lab Wiki - A1 introduction wiki.bambulab.com · 2026-08 · doc
  12. GitHub - bambulab organisation repository list (11 repos, checked Aug 2026) github.com · 2026-08 · doc
  13. GitHub - prusa3d/Prusa-Firmware-Buddy (firmware for MINI, MK4, XL and CORE One) github.com · 2026-08 · doc
  14. Original Prusa MK4S 3D Printer product page (Technical Parameters + CORE One+/MK4S/XL comparison table) prusa3d.com · 2026-08 · vendor
  15. Bambu Lab Warranty Policy bambulab.com · 2026-08 · vendor
  16. Prusa Knowledge Base - Warranty help.prusa3d.com · 2026-08 · doc