3D Printing InfoPrinter comparison
ANYCUBIC Photon Mono M5s vs ELEGOO Neptune 4 Plus
Compare hardware, build volume, printing specifications, dated prices and sources.
2 selected · all documented properties
Open these two in the interactive comparisonMore ANYCUBIC Photon Mono M5s comparisonsMore ELEGOO Neptune 4 Plus comparisons
| Property | ANYCUBIC Photon Mono M5sRESIN | ELEGOO Neptune 4 PlusBEDSLINGER |
|---|---|---|
| Identity | ||
| Brand | Anycubic | ELEGOO |
| Class | RESIN | BEDSLINGER |
| Identity & Market | ||
| Manufacturer & exact marketed model name (verify the exact product identity first) | ANYCUBIC Photon Mono M5s[1][2] | ELEGOO Neptune 4 Plus[3] |
| Release date (announcement and actual shipping) | Not documented | Listed on the ELEGOO US store from 20 September 2023 (Shopify publish date), the same date as the Neptune 4 Max[4][5] |
| Street price (USD; dated snapshot per entry) | $609.00 on store.anycubic.com, with the compare-at price also $609.00, but marked Sold out, checked Aug 2026. 3DJake also shows it sold out and delisted[1][2] | $309.00 on us.elegoo.com, Aug 2026, against a compare-at price of $425.00. Only a Ribbon-Cable printhead variant is listed for the Plus, unlike the Neptune 4 and 4 Max which also offer a Type-C version[4][6][5] |
| Variants & sibling models — and how to tell them apart (spec-contamination risk) | Older and smaller than the M7 family: 12K LCD (11520 x 5120) vs 14K, 218 x 123 x 200 mm vs 223 x 126 x 230, an LED-matrix light source rather than COB + Fresnel, and 105 vs 150-170 mm/h on high-speed resin. Note Anycubic's spec table lists the machine dimensions in H x W x D order[1][2][7][8] | Middle model of the Neptune 4 family. Against the base Neptune 4: bigger (320 x 320 x 385 mm), but a lower bed ceiling (100 C rather than 110 C) and much lower acceleration (12000 rather than 20000 mm/s2). Against the Max: smaller and lighter (14.4 kg against 18.1 kg) but with a higher bed ceiling (100 C against 85 C) and higher acceleration (12000 against 8000). Its Z drive is 2 lead screws with 2 tie rods, where the Centauri machines use 3 lead screws[3][9][10][11] |
| Physical & Frame | ||
| Build volume X×Y×Z (mm) — advertised vs actually usable | 218 x 123 x 200 mm (Anycubic quotes 5.4 L; the table writes it as 200 x 218 x 123 mm in H x W x D order)[1][2] | 320 x 320 x 385 mm; printing platform 330 x 330 mm[3] |
| Machine footprint (mm) & clearance needed (cable/spool overhang) | 460 x 270 x 290 mm (H x W x D per Anycubic; 3DJake writes 270 x 290 x 460 mm)[1][2] | 533 x 517 x 638 mm; ELEGOO also publishes a maximum size for machine activity of 578 x 750 x 860 mm including rack and tray, so allow 750 mm of depth[3] |
| Net weight (kg) | 8.9 kg[1][2] | 14.4 kg net, 16.65 kg gross[3] |
| Frame construction & material | Not documented | CNC-machined aluminium extrusion frame (Neptune 4 family)[9] |
| Enclosure: open / enclosed; panel material; door/lid | Open-frame MSLA with a UV-blocking cover[1] | Open frame, no enclosure[3] |
| Kinematics & Motion Hardware | ||
| Kinematics (bedslinger i3 / CoreXY / other) | MSLA, single Z axis on double linear guides, straight-lift peel[1][2] | Cartesian i3 bed-slinger[3] |
| Z-axis: leadscrew count & type, sync mechanism, anti-backlash | Double linear guides, 10 um precision[1] | Two lead screws with two tie rods[3] |
| Stepper drivers (exact model e.g. TMC2209; UART/SPI; sensorless homing?) | Not documented | "Silent Drive (All Axes)" is all ELEGOO publishes; the driver part number is not given on the product page[3] |
| Speed & Acceleration | ||
| Max print speed (claimed, mm/s) | Not documented | 30-500 mm/s printing speed, with 250 mm/s given by ELEGOO as the recommended figure - the 500 mm/s number is a ceiling, not a working speed[3] |
| Recommended/typical print speed | Not documented | 250 mm/s recommended printing speed (manufacturer figure)[3] |
| Max acceleration (claimed, mm/s²) | Not documented | 12000 mm/s2 maximum acceleration; default acceleration 5000 mm/s2[3] |
| Extruder | ||
| Type (direct drive / bowden) & design name | Not documented | Dual-gear direct extruder with 2 fans (the Centauri machines use a 1-fan version)[3][11] |
| Hotend & Nozzle | ||
| Hotend design (proprietary/standard; quick-swap mechanism?) | Not documented | Brass nozzle, 0.4 mm, with a titanium-alloy heat break[3] |
| Max nozzle temp claimed AND firmware max temp limit (both values) | Not documented | 300 C claimed max nozzle temperature[3] |
| Heated Bed & Surface | ||
| Max bed temp claimed AND firmware limit | Not documented | 100 C max heated bed temperature at 25 C ambient[3] |
| Bed surface (material, texture, coating), single/double-sided | Laser-engraved aluminium-alloy build platform[1][2] | PEI spring steel sheet; ELEGOO notes it is now upgraded to a dual-sided textured PEI + PLA-specific surface[3] |
| Leveling & Z-Offset | ||
| Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe) | Levelling-free design[1][2] | Manual levelling combined with 121-point auto-levelling[3] |
| Filament Handling & Detection | ||
| Filament runout sensor (type, location) | Not documented | Filament run-out sensor and power-loss recovery; no camera, no clog detection, no auto filament unloading[3] |
| Electronics & Power | ||
| Mainboard model & MCU (exact chip markings if teardowns exist) | Not documented | ELEGOO describes it only as a "Klipper High-Speed Quiet Motherboard" - no board model or MCU is published[3] |
| Total rated power draw | 100 W rated[1][2] | 320 W rated power; 24 V output; 110-120 V / 220-240 V input[3] |
| Firmware & Openness | ||
| Firmware base & current version (Klipper fork / Marlin fork / proprietary) | Not documented | Klipper (ELEGOO names the system "Klipper" outright for the Neptune 4 Plus, rather than the ELEGOO OS branding used on the Centauri machines)[3][11] |
| Connectivity, UI & Camera | ||
| Display: size, type, touch? | 4.3-inch TFT touchscreen (control panel — not the masking LCD, see W1)[1][2] | 4.3-inch colour capacitive touch screen[3] |
| On-device UI capabilities (model preview, per-object controls, etc.) | Not documented | Colour capacitive touch UI; ElegooSlicer is recommended, with Orca and Cura also supported[3] |
| WiFi (band/standard), Ethernet, USB ports, SD/flash-drive | USB Type-A 2.0 and Wi-Fi[1][2] | USB, LAN and Wi-Fi[3] |
| Materials Support | ||
| Officially supported filament list | 405 nm photopolymer resin; no closed compatibility list published on this page[1] | PLA, TPU, PETG, ABS, ASA, Nylon[3] |
| Noise & Power Consumption | ||
| Noise: claimed dB and independently measured dB (distance/method) | Not documented | Operating sound is published as 65 dB or less - a manufacturer figure with no measuring distance or method given, so it is not comparable with a reviewer's dB reading[3] |
| Reliability, Support & Ecosystem | ||
| Warranty length & support reputation (evidence, not vibes) | Not documented | 12 months on brand-new machines and parts, but ELEGOO's own table excludes a long list of parts from that: PEI plate / build plate / nozzle kit / PTFE tube / heater / thermistor / hot end / packaging / manual / tools carry no warranty at all, and the extruder, extruder kit and printhead kit get 6 months. Certified pre-owned machines carry no warranty[12] |
| Resin & MSLA | ||
| Masking LCD | 10.1-inch monochrome masking LCD at 12K, 11,520 x 5,120 px, 480:1 contrast, XY pixel pitch 19 x 24 um (manufacturer specification)[1][2] | Not documented |
| Light source | LED matrix UV light source. Anycubic does not publish wavelength or collimating optics for this model[1][2] | Not documented |
| Vertical print speedmm/h | 105 mm/h with high-speed resin, 70 mm/h with standard resin (manufacturer claims; Anycubic labels these average printing speeds and does not state the layer height assumed)[1][2] | Not documented |
| LCD life & replaceability | Swappable scratchproof screen protector film over the masking LCD. Anycubic publishes no rated screen life in hours[2] | Not documented |
| Resin vat & feeding | Unibody resin vat with scale lines. Capacity not published; no auto-refill and no level sensing stated for this model[1] | Not documented |
Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.
Sources for this comparison
- Anycubic Photon Mono M5s product page store.anycubic.com · 2026-08 · vendor
- Anycubic Photon Mono M5s technical data table 3djake.com · 2026-08 · vendor
- ELEGOO Neptune 4 Plus product page (full specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Plus Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Max Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
- Anycubic Photon Mono M7 product page store.anycubic.com · 2026-08 · vendor
- Anycubic Photon Mono M7 Pro product page store.anycubic.com · 2026-08 · vendor
- ELEGOO Neptune 4 product page (Specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Max product page (Specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Centauri Carbon product page (full specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Refund & Warranty policy (warranty period table) us.elegoo.com · 2026-08 · vendor