3D Printing Info

Printer comparison

Anycubic Kobra 2 vs ELEGOO Neptune 4 Max

Compare hardware, build volume, printing specifications, dated prices and sources.

Anycubic Kobra 2 guideELEGOO Neptune 4 Max guide

2 selected · all documented properties

Open these two in the interactive comparisonMore Anycubic Kobra 2 comparisonsMore ELEGOO Neptune 4 Max comparisons
Anycubic Kobra 2 vs ELEGOO Neptune 4 Max — documented properties and sources
PropertyAnycubic Kobra 2BEDSLINGERELEGOO Neptune 4 MaxBEDSLINGER
Identity
BrandAnycubicELEGOO
ClassBEDSLINGERBEDSLINGER
Identity & Market
Manufacturer & exact marketed model name (verify the exact product identity first)Anycubic Kobra 2[1]ELEGOO Neptune 4 Max[2]
Release date (announcement and actual shipping)Listed on the Anycubic store from 15 May 2023 (Shopify publish date)[1]Listed on the ELEGOO US store from 20 September 2023 (Shopify publish date)[3]
Street price (USD; dated snapshot per entry)$169.00 on store.anycubic.com, Aug 2026, against a compare-at price of $279.00 - the cheapest machine in this file[1]$389.00 on us.elegoo.com, Aug 2026, against a compare-at price of $559.99; Ribbon-Cable and Type-C printhead variants are the same price[3]
Variants & sibling models — and how to tell them apart (spec-contamination risk)Base model of a five-way family that is easy to confuse. All of Kobra 2, Kobra 2 Neo and Kobra 2 Pro share the same 220 x 220 x 250 mm build volume, but their speed ceilings differ: Neo 250 mm/s max / 150 typical, Kobra 2 300 / 200, Kobra 2 Pro 500 / 300. The Plus (320 x 320 x 400 mm) and Max (420 x 420 x 500 mm) are bigger but drop the bed ceiling to 90 C where the three small ones reach 110 C. Anycubic's own note: Kobra 2 firmware must be at V3.0.6 or above for the quoted speed[1][4][5][6][7]Largest Neptune 4. The trade-off against the smaller models is easy to miss: the bed only reaches 85 C (against 100 C on the Plus and 110 C on the base Neptune 4) and acceleration is capped at 8000 mm/s2 (against 12000 and 20000), because of the mass of a 430 x 430 mm moving bed. Two printhead variants, Ribbon-Cable and Type-C, are sold under one SKU[2][8][9][3]
Physical & Frame
Build volume X×Y×Z (mm) — advertised vs actually usable250 x 220 x 220 mm stated HWD, i.e. 220 x 220 x 250 mm in X x Y x Z; Anycubic quotes 12.1 L[1]420 x 420 x 480 mm; printing platform 430 x 430 mm[2]
Machine footprint (mm) & clearance needed (cable/spool overhang)486 x 440 x 435 mm stated as HWD, so the desk footprint is about 440 x 435 mm and the height is 486 mm[1]658 x 632 x 740 mm; ELEGOO's maximum size for machine activity is 658 x 950 x 960 mm including rack and tray - allow nearly a metre of depth and height[2]
Net weight (kg)8.4 kg[1]18.1 kg net, 21.8 kg gross[2]
Frame construction & materialNot documentedCNC-machined aluminium extrusion frame[2]
Enclosure: open / enclosed; panel material; door/lidOpen frame, no enclosure[1]Open frame, no enclosure[2]
Kinematics & Motion Hardware
Kinematics (bedslinger i3 / CoreXY / other)Cartesian bed-slinger with a gantry frame; Anycubic describes double metal spindles with SG15 bearings on the moving axes[1]Cartesian i3 bed-slinger[2]
Z-axis: leadscrew count & type, sync mechanism, anti-backlashDouble-threaded rod Z axis (dual lead screws)[1]Two lead screws with two tie rods[10]
Stepper drivers (exact model e.g. TMC2209; UART/SPI; sensorless homing?)Not documented"Silent Drive (All Axes)"; no driver part number published[10]
Speed & Acceleration
Max print speed (claimed, mm/s)300 mm/s maximum print speed (Anycubic Lab figure; firmware V3.0.6 or above required)[1]500 mm/s max toolhead speed (manufacturer claim)[2]
Recommended/typical print speed200 mm/s recommended print speed (manufacturer figure) - the number to plan around, not the 300 mm/s headline[1]250 mm/s recommended printing speed against the 500 mm/s ceiling (ELEGOO's own figure); default acceleration is 4000 mm/s2[10]
Max acceleration (claimed, mm/s²)3000 mm/s2 acceleration (manufacturer figure) - modest next to the 20000 mm/s2 of the current Kobra generation[1][11]8000 mm/s2 max toolhead acceleration (manufacturer claim) - the lowest in the Neptune 4 family[2]
Extruder
Type (direct drive / bowden) & design nameDirect drive with a dual-geared extrusion structure[1]Dual-gear direct extruder with 2 fans[10]
Hotend & Nozzle
Hotend design (proprietary/standard; quick-swap mechanism?)Not documentedBrass nozzle, 0.4 mm, with a titanium-alloy heat break[10]
Max nozzle temp claimed AND firmware max temp limit (both values)260 C nozzle temperature ceiling; 0.4 mm replaceable nozzle[1]300 C claimed max nozzle temperature[2]
Heater cartridge power (W)60 W hotend heater (Anycubic states "upgraded extruder power reaches up to 60 watts")[1]Not documented
Heated Bed & Surface
Max bed temp claimed AND firmware limit110 C hotbed temperature ceiling[1]85 C max heated bed temperature at 25 C ambient - well below the 100-110 C of the smaller Neptunes, which limits ABS/ASA work despite them being on the compatibility list[2]
Bed surface (material, texture, coating), single/double-sidedNot documentedPEI spring steel sheet, now upgraded to a dual-sided textured PEI + PLA-specific surface; platform 430 x 430 mm[10]
Leveling & Z-Offset
Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe)Anycubic LeviQ 2.0 automatic levelling with smart Z-offset and a user-adjustable Z compensation value[1]Manual levelling combined with 121-point auto-levelling[10]
Filament Handling & Detection
Filament runout sensor (type, location)Filament run-out sensor fitted, with power-loss recovery[1]Filament detection and power-loss resume printing[2]
Cooling & Air Handling
Part-cooling fan(s): count, size, ducting designPart-cooling fan rated to 7000 rpm (Anycubic figure)[1]Not documented
Electronics & Power
Mainboard model & MCU (exact chip markings if teardowns exist)Not documented"Klipper High-Speed Quiet Motherboard" is all ELEGOO publishes[10]
Input voltage (110/220 V, switch or auto)Not documented100-120 V / 220-240 V, 50/60 Hz[2][10]
Total rated power drawNot documented320 W rated power, 24 V output[10]
Firmware & Openness
Firmware base & current version (Klipper fork / Marlin fork / proprietary)Not documentedKlipper[10]
Connectivity, UI & Camera
Display: size, type, touch?4.3-inch colour LCD touchscreen[1]4.3-inch colour capacitive touch screen[10]
On-device UI capabilities (model preview, per-object controls, etc.)Not documentedColour capacitive touch UI; ElegooSlicer recommended, Orca and Cura supported[10]
WiFi (band/standard), Ethernet, USB ports, SD/flash-drivemicroSD card[1]Wi-Fi, USB and WLAN file transfer[2]
Calibration Routines & QoL
Assembly level & time from unbox to first printModular assembly - Anycubic states 5 pieces in about 10 minutes[1]Not documented
Materials Support
Officially supported filament listPLA, ABS, PETG, TPU[1]PLA, TPU, PETG, ABS, ASA, Nylon - but note the 85 C bed ceiling against ABS and ASA[2]
Noise & Power Consumption
Noise: claimed dB and independently measured dB (distance/method)Not documentedOperating sound published as 65 dB or less - a manufacturer figure with no distance or method stated[10]
Reliability, Support & Ecosystem
Warranty length & support reputation (evidence, not vibes)One year on the complete machine (excluding gifted and second-hand machines), with component warranty periods that vary by part; the period starts on the delivery date and is suspended while a replacement is in transit. Anycubic states it will follow longer local statutory periods where they apply[12]12 months on brand-new machines and parts, but ELEGOO's own table excludes a long list of parts from that: PEI plate / build plate / nozzle kit / PTFE tube / heater / thermistor / hot end / packaging / manual / tools carry no warranty at all, and the extruder, extruder kit and printhead kit get 6 months. Certified pre-owned machines carry no warranty[13]

Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.

Sources for this comparison

  1. Anycubic Kobra 2 store page and Shopify product JSON (Tech Specs block, price, store publish date) store.anycubic.com · 2026-08 · vendor
  2. ELEGOO Neptune 4 Max product page (Specification table) us.elegoo.com · 2026-08 · vendor
  3. ELEGOO Neptune 4 Max Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
  4. Anycubic Kobra 2 Neo store page and Shopify product JSON (Tech Specs block, price, store publish date) store.anycubic.com · 2026-08 · vendor
  5. Anycubic Kobra 2 Pro store page and Shopify product JSON (Tech Specs block, price, store publish date) store.anycubic.com · 2026-08 · vendor
  6. Anycubic Kobra 2 Plus store page and Shopify product JSON (Tech Specs block, price, store publish date) store.anycubic.com · 2026-08 · vendor
  7. Anycubic Kobra 2 Max store page and Shopify product JSON (Tech Specs block, price, store publish date) store.anycubic.com · 2026-08 · vendor
  8. ELEGOO Neptune 4 product page (Specification table) us.elegoo.com · 2026-08 · vendor
  9. ELEGOO Neptune 4 Plus product page (full specification table) us.elegoo.com · 2026-08 · vendor
  10. ELEGOO compare-products page, which embeds the full per-model specification JSON for every Neptune, Centauri and OrangeStorm machine us.elegoo.com · 2026-08 · vendor
  11. Anycubic Kobra 4 product page (Specifications table) store.anycubic.com · 2026-08 · vendor
  12. Anycubic refund and warranty policy store.anycubic.com · 2026-08 · vendor
  13. ELEGOO Refund & Warranty policy (warranty period table) us.elegoo.com · 2026-08 · vendor