3D Printing InfoPrinter comparison
AnkerMake M5C vs ELEGOO Neptune 4
Compare hardware, build volume, printing specifications, dated prices and sources.
2 selected · all documented properties
Open these two in the interactive comparisonMore AnkerMake M5C comparisonsMore ELEGOO Neptune 4 comparisons
| Property | AnkerMake M5CBEDSLINGER | ELEGOO Neptune 4BEDSLINGER |
|---|---|---|
| Identity | ||
| Brand | AnkerMake | ELEGOO |
| Class | BEDSLINGER | BEDSLINGER |
| Identity & Market | ||
| Manufacturer & exact marketed model name (verify the exact product identity first) | AnkerMake M5C. AnkerMake has since been rebranded eufyMake[1][2] | ELEGOO Neptune 4 (spec table "Product Model: Neptune 4")[3] |
| Release date (announcement and actual shipping) | Not documented | Listed on the ELEGOO US store from 27 May 2023 (Shopify publish date)[4] |
| Street price (USD; dated snapshot per entry) | $399 as stated on eufyMake's own M5C write-up, checked Aug 2026; that page is a buying guide rather than a live cart listing. 3DJake shows the machine sold out and no longer stocked[2][1] | $219.00 on us.elegoo.com, Aug 2026, against a compare-at price of $249.00; both the Ribbon-Cable and Type-C printhead variants are the same price[4] |
| Variants & sibling models — and how to tell them apart (spec-contamination risk) | Cheaper counterpart to the M5. It is smaller (220x220x250 vs 235x235x250), has a higher flow rate (35 vs 24 mm3/s), and drops the 4.3-inch screen, the camera and AI recognition entirely — control is via the app plus a single one-click button. The 500 mm/s figure is a fast-mode claim; the default is 250 mm/s[1][2][5] | Two printhead variants of the same machine are sold under one SKU - "Ribbon-Cable Version" and "Type-C Version" - which use different printhead parts. Within the Neptune 4 family the numbers diverge sharply and get mixed up constantly: Neptune 4 is 225 x 225 x 265 mm with a 110 C bed and 20000 mm/s2; the Plus is 320 x 320 x 385 mm with a 100 C bed and 12000 mm/s2; the Max is 420 x 420 x 480 mm with an 85 C bed and only 8000 mm/s2. The Neptune 4 Pro is a separate model again[4][3][6][7] |
| Market position: superseded? successor announced? | 3DJake lists it as sold out and no longer stocked; the brand is now eufyMake[1][2] | Still listed in ELEGOO's US store Neptune section in Aug 2026 alongside the 4 Pro, 4 Plus and 4 Max, but ELEGOO's current development is on the Centauri line[8] |
| Physical & Frame | ||
| Build volume X×Y×Z (mm) — advertised vs actually usable | 220 x 220 x 250 mm[1][2] | 225 x 225 x 265 mm; the PEI platform itself is 235 x 235 mm[3] |
| Machine footprint (mm) & clearance needed (cable/spool overhang) | Not documented | 475 x 445 x 515 mm. ELEGOO separately publishes a "maximum size for machine activity" of 475 x 550 x 735 mm including rack and tray - the depth to allow for is 550 mm, not 445 mm[3] |
| Net weight (kg) | Not documented | 8.3 kg net, 10.6 kg gross[3] |
| Frame construction & material | Die-cast aluminium-alloy base; eufyMake describes the Z axis as aerospace-grade aluminium alloy[2] | CNC-machined aluminium extrusion frame[3] |
| Enclosure: open / enclosed; panel material; door/lid | Open frame[1] | Open frame, no enclosure[3] |
| Kinematics & Motion Hardware | ||
| Kinematics (bedslinger i3 / CoreXY / other) | Cartesian bedslinger with a single Y-axis belt[1] | Cartesian i3 bed-slinger[3] |
| Z-axis: leadscrew count & type, sync mechanism, anti-backlash | Not documented | Two lead screws (the Neptune 4 Plus and Max add two tie rods to the same arrangement)[9] |
| Stepper drivers (exact model e.g. TMC2209; UART/SPI; sensorless homing?) | Not documented | "Silent Drive (All Axes)" is all ELEGOO publishes; no driver part number is given[9] |
| Speed & Acceleration | ||
| Max print speed (claimed, mm/s) | 250 mm/s default; 500 mm/s in high-speed mode (manufacturer figures)[1][2] | 500 mm/s max toolhead speed (manufacturer claim); the Neptune 4 Plus page for the same family states a recommended 250 mm/s[3][6] |
| Recommended/typical print speed | Not documented | 250 mm/s recommended printing speed against the 500 mm/s ceiling (ELEGOO's own figure)[9] |
| Max acceleration (claimed, mm/s²) | 5,000 mm/s2 in high-speed mode (manufacturer claim)[1] | 20000 mm/s2 max toolhead acceleration (manufacturer claim) - notably higher than the Plus at 12000 and the Max at 8000, because the moving mass is smaller[3][6][7] |
| Max volumetric flow claimed (mm³/s) | 35 mm3/s (manufacturer claim)[2] | Not documented |
| Extruder | ||
| Type (direct drive / bowden) & design name | Direct-drive extruder[1] | Dual-gear direct extruder with 2 fans[9] |
| Hotend & Nozzle | ||
| Hotend design (proprietary/standard; quick-swap mechanism?) | All-metal hotend[2] | Brass nozzle, 0.4 mm, with a copper and titanium-alloy heat break - the Plus and Max use a titanium-alloy heat break only[9] |
| Max nozzle temp claimed AND firmware max temp limit (both values) | Up to 300 °C (manufacturer claim)[2] | 300 C claimed max nozzle temperature[3] |
| Heated Bed & Surface | ||
| Max bed temp claimed AND firmware limit | Not documented | 110 C max heated bed temperature[3] |
| Bed surface (material, texture, coating), single/double-sided | Not documented | PEI spring steel sheet, now upgraded by ELEGOO to a dual-sided textured PEI + PLA-specific surface[9] |
| Leveling & Z-Offset | ||
| Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe) | 49-point (7 x 7) automatic bed levelling; probe technology not named[2] | Manual levelling combined with 121-point auto-levelling; no full-auto calibration on this model[9] |
| Mesh grid size (probe point count — firmware evidence) | 49 points[2] | Not documented |
| Filament Handling & Detection | ||
| Filament runout sensor (type, location) | Not documented | Filament detection fitted; power-loss resume printing supported[3] |
| Electronics & Power | ||
| Mainboard model & MCU (exact chip markings if teardowns exist) | Not documented | ELEGOO describes it only as a "Klipper High-Speed Quiet Motherboard" - no board model or MCU published[9] |
| Input voltage (110/220 V, switch or auto) | Not documented | 115/230 V, 50/60 Hz on the product page; ELEGOO's compare page gives 110-120 / 220-240 VAC 50/60 Hz[3][9] |
| Total rated power draw | Not documented | 310 W rated power, 24 V output[9] |
| Firmware & Openness | ||
| Firmware base & current version (Klipper fork / Marlin fork / proprietary) | Not documented | Klipper (ELEGOO names the system "Klipper" outright for the Neptune 4 series, rather than the ELEGOO OS branding used on the Centauri machines)[9][10] |
| Connectivity, UI & Camera | ||
| Display: size, type, touch? | None. 3DJake's table records "Printer display: None" and eufyMake confirms there is no screen[1][2] | 4.3-inch colour capacitive touch screen[9] |
| On-device UI capabilities (model preview, per-object controls, etc.) | Not documented | Colour capacitive touch UI; ElegooSlicer recommended, with Orca and Cura also supported[9] |
| WiFi (band/standard), Ethernet, USB ports, SD/flash-drive | Wi-Fi; eufyMake also cites Bluetooth for app pairing[1][2] | LAN and USB file transfer; no Wi-Fi is listed for the base Neptune 4, unlike the Plus (USB/LAN/Wi-Fi) and Max (Wi-Fi/USB/WLAN)[3][6][7] |
| Camera: built-in / optional? Resolution & framerate (verify — marketing often omits real fps) | None. No camera and no AI recognition on this model[1][2] | Not documented |
| Calibration Routines & QoL | ||
| Assembly level & time from unbox to first print | Assembly kit[1] | Not documented |
| Materials Support | ||
| Officially supported filament list | PLA, TPU, PETG and others; eufyMake does not publish a closed list[2] | PLA, TPU, PETG, ABS, ASA, Nylon[3] |
| Noise & Power Consumption | ||
| Noise: claimed dB and independently measured dB (distance/method) | Not documented | Operating sound published as 60 dB or less - a manufacturer figure with no distance or method stated, so it is not comparable with an independently measured reading[9] |
| Reliability, Support & Ecosystem | ||
| Warranty length & support reputation (evidence, not vibes) | Not documented | 12 months on brand-new machines and parts, but ELEGOO's own table excludes a long list of parts from that: PEI plate / build plate / nozzle kit / PTFE tube / heater / thermistor / hot end / packaging / manual / tools carry no warranty at all, and the extruder, extruder kit and printhead kit get 6 months. Certified pre-owned machines carry no warranty[11] |
| Independently Measured Performance | ||
| Dimensional accuracy measurements (third-party, with numbers) | Print precision quoted at +/-0.1 mm (manufacturer specification, not an independent measurement)[1][2] | Not documented |
Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.
Sources for this comparison
- AnkerMake M5C technical data table 3djake.com · 2026-08 · vendor
- AnkerMake M5C review and spec summary (eufyMake) eufymake.com · 2026-08 · vendor
- ELEGOO Neptune 4 product page (Specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
- AnkerMake M5 technical data table 3djake.com · 2026-08 · vendor
- ELEGOO Neptune 4 Plus product page (full specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Max product page (Specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO US store 3D printers collection (current line-up, Aug 2026) us.elegoo.com · 2026-08 · vendor
- ELEGOO compare-products page, which embeds the full per-model specification JSON for every Neptune, Centauri and OrangeStorm machine us.elegoo.com · 2026-08 · vendor
- ELEGOO Centauri Carbon product page (full specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Refund & Warranty policy (warranty period table) us.elegoo.com · 2026-08 · vendor