3D Printing InfoPrinter comparison
AnkerMake M5 vs FlashForge Creator 4
Compare hardware, build volume, printing specifications, dated prices and sources.
2 selected · all documented properties
Open these two in the interactive comparisonMore AnkerMake M5 comparisonsMore FlashForge Creator 4 comparisons
| Property | AnkerMake M5BEDSLINGER | FlashForge Creator 4IDEX |
|---|---|---|
| Identity | ||
| Brand | AnkerMake | FlashForge |
| Class | BEDSLINGER | IDEX |
| Identity & Market | ||
| Manufacturer & exact marketed model name (verify the exact product identity first) | AnkerMake M5. AnkerMake has since been rebranded eufyMake, and ankermake.com now redirects to eufymake.com[1][2] | Flashforge Creator 4, sold in A and S configurations (Creator 4A, Creator 4S)[3] |
| Street price (USD; dated snapshot per entry) | Not documented | $10,999.00 at Top 3D Shop with a 2-3 week lead time, checked Aug 2026[3] |
| Variants & sibling models — and how to tell them apart (spec-contamination risk) | Paired with the cheaper M5C, which is smaller (220x220x250 vs 235x235x250), has a higher flow rate (35 vs 24 mm3/s) but no screen, no camera and no AI recognition. The M5's headline 500 mm/s is a high-speed-mode figure; its default is 250 mm/s[1][4][2] | Two factory configurations that share the chassis but not the temperature ceiling: Creator 4A ships 2 x HT extruders (320 °C max, no composite support), Creator 4S ships 1 x HT + 1 x HS (360 °C max, supports PA-CF, PA-GF, PP-CF, PPS-CF). A third extruder type, F, is rated 265 °C and intended for flexibles. Any published "360 °C" figure applies only to the HS head[3] |
| Market position: superseded? successor announced? | 3DJake lists the M5 as sold out and no longer stocked. The brand has been folded into eufyMake[1][2] | Not documented |
| Physical & Frame | ||
| Build volume X×Y×Z (mm) — advertised vs actually usable | 235 x 235 x 250 mm[1][2] | 400 x 350 x 500 mm[3] |
| Machine footprint (mm) & clearance needed (cable/spool overhang) | Not documented | 840 x 675 x 1000 mm (1050 mm on the stand). FlashForge specifies an installation space of at least 1400 x 1500 x 1600 mm[3] |
| Net weight (kg) | Not documented | 90 kg net[3] |
| Frame construction & material | Not documented | Fully enclosed professional chassis on a stand[3] |
| Enclosure: open / enclosed; panel material; door/lid | Open frame[1] | Fully enclosed with HEPA 13 filtration and an actively controlled chamber[3] |
| Passive chamber temperature reached (if enclosed; measured values preferred) | Not documented | Up to 65 °C, actively controlled (manufacturer claim)[3] |
| Kinematics & Motion Hardware | ||
| Kinematics (bedslinger i3 / CoreXY / other) | Cartesian bedslinger[1] | IDEX — two independently driven extruders on the same gantry[3] |
| Speed & Acceleration | ||
| Max print speed (claimed, mm/s) | 250 mm/s default; 500 mm/s in high-speed mode (manufacturer figures)[1] | 10-200 mm/s, adjustable per material. On the 4S the HS head is quoted 100-150 mm/s and the HT head 100-200 mm/s (manufacturer figures)[3] |
| Max acceleration (claimed, mm/s²) | 5,000 mm/s2 in high-speed mode (manufacturer claim)[1] | Not documented |
| Max volumetric flow claimed (mm³/s) | 24 mm3/s (manufacturer claim)[2] | Not documented |
| Extruder | ||
| Type (direct drive / bowden) & design name | Direct-drive extruder[1] | Direct drive, two independent extruders, interchangeable modules (F / HT / HS)[3] |
| Hotend & Nozzle | ||
| Max nozzle temp claimed AND firmware max temp limit (both values) | Not documented | Depends on the fitted extruder module: F 265 °C, HT 320 °C, HS 360 °C[3] |
| Heater cartridge power (W) | 60 W heating block, quoted by AnkerMake as reaching 200 °C[1] | Not documented |
| Stock nozzle size & sizes included in box | Not documented | 0.4 mm default; 0.6 and 0.8 mm optional[3] |
| Heated Bed & Surface | ||
| Max bed temp claimed AND firmware limit | Not documented | 130 °C maximum (manufacturer claim)[3] |
| Bed surface (material, texture, coating), single/double-sided | Scratch-resistant PEI-coated magnetic build plate[1] | Not documented |
| Leveling & Z-Offset | ||
| Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe) | Automatic 7 x 7 levelling; probe technology not named[1] | Automatic bed levelling; FlashForge does not name the probe technology in this spec table[3] |
| Mesh grid size (probe point count — firmware evidence) | 49 points (7 x 7)[1] | Not documented |
| Filament Handling & Detection | ||
| Spool holder location & max spool size; drybox compatibility | Not documented | Two spool bays, 1 kg and 2 kg capacity[3] |
| Electronics & Power | ||
| Input voltage (110/220 V, switch or auto) | Not documented | AC 100-130 V / 200-240 V, 50-60 Hz, 30 A overcurrent protection[3] |
| Total rated power draw | Not documented | 2320 W rated[3] |
| Firmware & Openness | ||
| Firmware base & current version (Klipper fork / Marlin fork / proprietary) | Not documented | Not named; the supported slicer is FlashPrint[3] |
| Connectivity, UI & Camera | ||
| Display: size, type, touch? | 4.3-inch colour LCD touchscreen[1] | 7-inch touchscreen, 1024 x 600[3] |
| WiFi (band/standard), Ethernet, USB ports, SD/flash-drive | Wi-Fi and USB-C[1] | USB flash drive, Ethernet, Wi-Fi[3] |
| Camera: built-in / optional? Resolution & framerate (verify — marketing often omits real fps) | 1080p camera with AI recognition and time-lapse[1][2] | Not documented |
| Calibration Routines & QoL | ||
| Assembly level & time from unbox to first print | Assembly kit; AnkerMake quotes about 15 minutes[1] | Not documented |
| Materials Support | ||
| Officially supported filament list | Not documented | Standard and engineering plastics on the HT head; the HS head adds PA-CF, PA-GF, PP-CF and PPS-CF. Materials such as PC, PA and carbon fibre are the stated targets for the 130 °C bed[3] |
| Reliability, Support & Ecosystem | ||
| Warranty length & support reputation (evidence, not vibes) | Not documented | 12 months on the printer, 3 months on extruder parts[3] |
| Independently Measured Performance | ||
| Dimensional accuracy measurements (third-party, with numbers) | Print accuracy quoted at 0.1 mm (manufacturer specification, not an independent measurement)[1] | Not documented |
Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.
Sources for this comparison
- AnkerMake M5 technical data table 3djake.com · 2026-08 · vendor
- AnkerMake M5C review and spec summary (eufyMake) eufymake.com · 2026-08 · vendor
- Flashforge Creator 4 (A/S) product listing with full spec table top3dshop.com · 2026-08 · vendor
- AnkerMake M5C technical data table 3djake.com · 2026-08 · vendor