3D Printing InfoPrinter comparison
AnkerMake M5 vs ELEGOO Neptune 4 Plus
Compare hardware, build volume, printing specifications, dated prices and sources.
2 selected · all documented properties
Open these two in the interactive comparisonMore AnkerMake M5 comparisonsMore ELEGOO Neptune 4 Plus comparisons
| Property | AnkerMake M5BEDSLINGER | ELEGOO Neptune 4 PlusBEDSLINGER |
|---|---|---|
| Identity | ||
| Brand | AnkerMake | ELEGOO |
| Class | BEDSLINGER | BEDSLINGER |
| Identity & Market | ||
| Manufacturer & exact marketed model name (verify the exact product identity first) | AnkerMake M5. AnkerMake has since been rebranded eufyMake, and ankermake.com now redirects to eufymake.com[1][2] | ELEGOO Neptune 4 Plus[3] |
| Release date (announcement and actual shipping) | Not documented | Listed on the ELEGOO US store from 20 September 2023 (Shopify publish date), the same date as the Neptune 4 Max[4][5] |
| Street price (USD; dated snapshot per entry) | Not documented | $309.00 on us.elegoo.com, Aug 2026, against a compare-at price of $425.00. Only a Ribbon-Cable printhead variant is listed for the Plus, unlike the Neptune 4 and 4 Max which also offer a Type-C version[4][6][5] |
| Variants & sibling models — and how to tell them apart (spec-contamination risk) | Paired with the cheaper M5C, which is smaller (220x220x250 vs 235x235x250), has a higher flow rate (35 vs 24 mm3/s) but no screen, no camera and no AI recognition. The M5's headline 500 mm/s is a high-speed-mode figure; its default is 250 mm/s[1][7][2] | Middle model of the Neptune 4 family. Against the base Neptune 4: bigger (320 x 320 x 385 mm), but a lower bed ceiling (100 C rather than 110 C) and much lower acceleration (12000 rather than 20000 mm/s2). Against the Max: smaller and lighter (14.4 kg against 18.1 kg) but with a higher bed ceiling (100 C against 85 C) and higher acceleration (12000 against 8000). Its Z drive is 2 lead screws with 2 tie rods, where the Centauri machines use 3 lead screws[3][8][9][10] |
| Market position: superseded? successor announced? | 3DJake lists the M5 as sold out and no longer stocked. The brand has been folded into eufyMake[1][2] | Not documented |
| Physical & Frame | ||
| Build volume X×Y×Z (mm) — advertised vs actually usable | 235 x 235 x 250 mm[1][2] | 320 x 320 x 385 mm; printing platform 330 x 330 mm[3] |
| Machine footprint (mm) & clearance needed (cable/spool overhang) | Not documented | 533 x 517 x 638 mm; ELEGOO also publishes a maximum size for machine activity of 578 x 750 x 860 mm including rack and tray, so allow 750 mm of depth[3] |
| Net weight (kg) | Not documented | 14.4 kg net, 16.65 kg gross[3] |
| Frame construction & material | Not documented | CNC-machined aluminium extrusion frame (Neptune 4 family)[8] |
| Enclosure: open / enclosed; panel material; door/lid | Open frame[1] | Open frame, no enclosure[3] |
| Kinematics & Motion Hardware | ||
| Kinematics (bedslinger i3 / CoreXY / other) | Cartesian bedslinger[1] | Cartesian i3 bed-slinger[3] |
| Z-axis: leadscrew count & type, sync mechanism, anti-backlash | Not documented | Two lead screws with two tie rods[3] |
| Stepper drivers (exact model e.g. TMC2209; UART/SPI; sensorless homing?) | Not documented | "Silent Drive (All Axes)" is all ELEGOO publishes; the driver part number is not given on the product page[3] |
| Speed & Acceleration | ||
| Max print speed (claimed, mm/s) | 250 mm/s default; 500 mm/s in high-speed mode (manufacturer figures)[1] | 30-500 mm/s printing speed, with 250 mm/s given by ELEGOO as the recommended figure - the 500 mm/s number is a ceiling, not a working speed[3] |
| Recommended/typical print speed | Not documented | 250 mm/s recommended printing speed (manufacturer figure)[3] |
| Max acceleration (claimed, mm/s²) | 5,000 mm/s2 in high-speed mode (manufacturer claim)[1] | 12000 mm/s2 maximum acceleration; default acceleration 5000 mm/s2[3] |
| Max volumetric flow claimed (mm³/s) | 24 mm3/s (manufacturer claim)[2] | Not documented |
| Extruder | ||
| Type (direct drive / bowden) & design name | Direct-drive extruder[1] | Dual-gear direct extruder with 2 fans (the Centauri machines use a 1-fan version)[3][10] |
| Hotend & Nozzle | ||
| Hotend design (proprietary/standard; quick-swap mechanism?) | Not documented | Brass nozzle, 0.4 mm, with a titanium-alloy heat break[3] |
| Max nozzle temp claimed AND firmware max temp limit (both values) | Not documented | 300 C claimed max nozzle temperature[3] |
| Heater cartridge power (W) | 60 W heating block, quoted by AnkerMake as reaching 200 °C[1] | Not documented |
| Heated Bed & Surface | ||
| Max bed temp claimed AND firmware limit | Not documented | 100 C max heated bed temperature at 25 C ambient[3] |
| Bed surface (material, texture, coating), single/double-sided | Scratch-resistant PEI-coated magnetic build plate[1] | PEI spring steel sheet; ELEGOO notes it is now upgraded to a dual-sided textured PEI + PLA-specific surface[3] |
| Leveling & Z-Offset | ||
| Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe) | Automatic 7 x 7 levelling; probe technology not named[1] | Manual levelling combined with 121-point auto-levelling[3] |
| Mesh grid size (probe point count — firmware evidence) | 49 points (7 x 7)[1] | Not documented |
| Filament Handling & Detection | ||
| Filament runout sensor (type, location) | Not documented | Filament run-out sensor and power-loss recovery; no camera, no clog detection, no auto filament unloading[3] |
| Electronics & Power | ||
| Mainboard model & MCU (exact chip markings if teardowns exist) | Not documented | ELEGOO describes it only as a "Klipper High-Speed Quiet Motherboard" - no board model or MCU is published[3] |
| Total rated power draw | Not documented | 320 W rated power; 24 V output; 110-120 V / 220-240 V input[3] |
| Firmware & Openness | ||
| Firmware base & current version (Klipper fork / Marlin fork / proprietary) | Not documented | Klipper (ELEGOO names the system "Klipper" outright for the Neptune 4 Plus, rather than the ELEGOO OS branding used on the Centauri machines)[3][10] |
| Connectivity, UI & Camera | ||
| Display: size, type, touch? | 4.3-inch colour LCD touchscreen[1] | 4.3-inch colour capacitive touch screen[3] |
| On-device UI capabilities (model preview, per-object controls, etc.) | Not documented | Colour capacitive touch UI; ElegooSlicer is recommended, with Orca and Cura also supported[3] |
| WiFi (band/standard), Ethernet, USB ports, SD/flash-drive | Wi-Fi and USB-C[1] | USB, LAN and Wi-Fi[3] |
| Camera: built-in / optional? Resolution & framerate (verify — marketing often omits real fps) | 1080p camera with AI recognition and time-lapse[1][2] | Not documented |
| Calibration Routines & QoL | ||
| Assembly level & time from unbox to first print | Assembly kit; AnkerMake quotes about 15 minutes[1] | Not documented |
| Materials Support | ||
| Officially supported filament list | Not documented | PLA, TPU, PETG, ABS, ASA, Nylon[3] |
| Noise & Power Consumption | ||
| Noise: claimed dB and independently measured dB (distance/method) | Not documented | Operating sound is published as 65 dB or less - a manufacturer figure with no measuring distance or method given, so it is not comparable with a reviewer's dB reading[3] |
| Reliability, Support & Ecosystem | ||
| Warranty length & support reputation (evidence, not vibes) | Not documented | 12 months on brand-new machines and parts, but ELEGOO's own table excludes a long list of parts from that: PEI plate / build plate / nozzle kit / PTFE tube / heater / thermistor / hot end / packaging / manual / tools carry no warranty at all, and the extruder, extruder kit and printhead kit get 6 months. Certified pre-owned machines carry no warranty[11] |
| Independently Measured Performance | ||
| Dimensional accuracy measurements (third-party, with numbers) | Print accuracy quoted at 0.1 mm (manufacturer specification, not an independent measurement)[1] | Not documented |
Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.
Sources for this comparison
- AnkerMake M5 technical data table 3djake.com · 2026-08 · vendor
- AnkerMake M5C review and spec summary (eufyMake) eufymake.com · 2026-08 · vendor
- ELEGOO Neptune 4 Plus product page (full specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Plus Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Max Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
- AnkerMake M5C technical data table 3djake.com · 2026-08 · vendor
- ELEGOO Neptune 4 product page (Specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Max product page (Specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Centauri Carbon product page (full specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Refund & Warranty policy (warranty period table) us.elegoo.com · 2026-08 · vendor