3D Printing Info

Filament comparison

PA aramid vs PLA Metal

Compare printing settings, strength, heat resistance, dated prices and sources.

Aramid-fibre nylon guideMetal-filled PLA guide

2 selected · all documented properties

Open these two in the interactive comparisonMore PA aramid comparisonsMore PLA Metal comparisons
PA aramid vs PLA Metal — documented properties and sources
PropertyAramid-fibre nylonPAMetal-filled PLAPLA
Market snapshot
Listing priceUSD/kg; dated snapshotsNot documented$79.69/kg median; $24.99–$94.99/kg across 6 dated product listings
Identity & Market
Base polymer / chemistryAramid-fibre reinforced polyamide[1]PLA loaded with real metal powder — bronze, copper, steel or iron. Bambu Lab's PLA Sparkle TDS states it has "metal particles included in its composition"; its separately sold PLA Metal does not, and the store page says so explicitly[2][3][4][5][6][7]
Densityg/cm³Not documented1.26 (Bambu Lab Sparkle, a trace-metal glitter grade) up to 3.9–4.0 for colorFabb bronze and copper and 2.3 for Proto-pasta steel, ISO 1183[5][2][3][8]
Typical priceUSD/kgNot documented1 kg spools cluster near 78[9][10][4]
Price range across brandsUSD/kgNot documented25–95 across brands; Bambu Lab Sparkle 25, Proto-pasta iron 65, colorFabb bronze and copper 84, Proto-pasta steel 95[9][4][10][8]
Market availability1–5Special order, 1–2 makers worldwide — no aramid-filled nylon filament was found in any catalogue searched; the aramid filaments that do exist in the retail market use an ASA matrix[11][12]Available from several mainstream brands[10][4][8][9]
Spool sizes & diametersNot documented1.75 and 2.85 mm; 0.1, 0.5, 0.75, 1 and 1.5 kg spools[13][10]
Typical applicationsNot documentedDecorative castings and props that are polished or left to patinate; the density gives prints a metallic heft[2][4]
Printing Parameters
Nozzle temperature°CNot documented195–220 (colorFabb bronze and copper); 192 (Proto-pasta iron); 198 (Proto-pasta steel); 190–230 (Bambu Lab Sparkle)[2][4][8][5]
Bed temperature°CNot documented50–60 (colorFabb, Proto-pasta); 35–45 (Bambu Lab)[2][4][5]
Enclosure / chamber requirement1–5Enclosure required (passive) — as for every nylon[1]Open frame is fine[2]
Part cooling fanNot documentedOn (colorFabb copper); 0–100 % (colorFabb bronze)[2][3]
Bed surface & adhesion aidNot documentedGlass plate with glue stick or tape (colorFabb)[2][3]
Maximum volumetric flow (mm³/s; see test conditions)mm³/sNot documented1.6–2.4 at Proto-pasta's 20–30 mm/s for iron and steel, 3.2–8 at colorFabb's 40–100 mm/s, on a 0.4 mm nozzle at 0.2 mm layer[4][8][2][14]
Overall printing difficulty1–5Not documentedIntermediate — dry filament and a tuned profile; brittle in filament form and slow to print[4][8]
Extruder requirementNot documentedProto-pasta advises an extrusion width 0.05 mm larger than the nozzle and warns that feeding is inconsistent below 0.4 mm and on Bowden machines[4][8]
Hardware Wear & Reliability
Nozzle hardness required1–4Hardened steel required — no aramid-filled nylon datasheet was obtainable; Polymaker measures about 9 h of brass nozzle life on its fibre-filled nylons[15]Brass acceptable; hardened steel for volume work[4][8]
Abrasiveness1–5Highly abrasive — fibre-reinforced nylon composite[15]Moderately abrasive — metal fill[4][8]
Nozzle clog risk1–5High — jams from moisture, heat creep or particles; nylon already needs a drybox and Prusa names kevlar among the fibres that raise nozzle-clogging risk[16]Moderate — needs dry filament and a clean nozzle[8]
Hotend requirementNot documentedProto-pasta recommends a wear-resistant or larger nozzle for longer service intervals[4][8]
Other hardware wearNot documentedProto-pasta warns of more frequent nozzle replacement and first-layer adjustment[4][8]
Moisture Behaviour
Moisture absorption (hygroscopicity)1–5Very high (>2 %) — the polyamide matrix governs uptake[17]Moderate — the PLA matrix takes up 0.40–0.51 % saturated; the metal powder itself does not absorb water[18][19]
Effect of moisture on strengthPolymaker's printed dry-versus-wet blocks for its CoPA nylon show what conditioning does to the family: tensile 78.0 → 34.3 MPa and modulus 2703 → 724 MPa, with notched Charpy rising 6.9 → 27.7 kJ/m². Fibre reinforcement reduces but does not remove the effect[20][21]Polymaker rates PLA low-sensitivity and publishes no dry-versus-conditioned figures for this grade; absorbed water flashes to steam and shows as bubbling and poor layer adhesion[17]
Mechanical Properties
Tensile strength (XY)MPaNot documented25 (colorFabb copper) and 30 (colorFabb bronze), ISO 527-1A; Bambu Lab Sparkle 39 ± 3 printed XY, ISO 527[2][3][5]
Young's modulusMPaNot documented1940 ± 230 printed XY, ISO 527 (Bambu Lab Sparkle)[5]
Elongation at break%Not documented3–10 (colorFabb copper) and 5–10 (colorFabb bronze), ISO 527-1A; 11.7 for Bambu Lab Sparkle printed XY[2][3][5]
Flexural strengthMPaNot documented75 ± 4 printed XY, ISO 178 (Bambu Lab Sparkle)[5]
Flexural modulusMPaNot documented2350 ± 140 printed XY, ISO 178 (Bambu Lab Sparkle)[5]
Charpy impact, notchedkJ/m²Not documented23.2 ± 2.4 printed XY, ISO 179, notched (Bambu Lab Sparkle)[5]
Other impact dataNot documentedIzod notched 4.5 kJ/m² for colorFabb bronzeFill and 10 kJ/m² for copperFill (ISO 180); Charpy unnotched 66.5 kJ/m² for Bambu Lab Sparkle[2][3][5]
Layer adhesion / Z tensileMPaNot documented32 ± 2 printed Z, ISO 527 (Bambu Lab Sparkle)[5]
Brittleness1–5Not documentedBrittle — Proto-pasta describes both its iron and steel grades as more brittle than standard PLA in filament form[4][8]
Creep resistance / sustained load1–5Not documentedPoor — no metal-filled creep test; plain printed PLA sagged from 12 to 16.2–21.8 mm over 5 days at 1.25 kg[22][23][24]
Fatigue / repeated-flex resistance1–5Not documentedPoor — no grade-specific S-N curve; plain printed PLA ran 38 000–49 000 cycles at 30 % of tensile strength and Proto-pasta describes its iron and steel grades as more brittle than standard PLA[25][4][8]
Elasticity / flexibility1–5Not documentedRigid[5]
Z strength as % of XY%Not documented82 by tensile (printed, Bambu Lab Sparkle)[5]
Thermal Properties
HDT at 0.45 MPa°CNot documented55 (ISO 75, 0.45 MPa, Bambu Lab Sparkle)[5]
HDT at 1.8 MPa°CNot documented53 (ISO 75, 1.8 MPa, Bambu Lab Sparkle)[5]
Glass transition (Tg)°CNot documented56 (DSC, Bambu Lab Sparkle)[5]
Melting point / Vicat°CNot documented156 peak melt (DSC, Bambu Lab Sparkle)[5]
Environment & Chemical
UV resistance1–5Not documentedDegrades within weeks outdoors[26]
Outdoor durabilityNot documentedProto-pasta markets its iron grade as rustable — the iron oxidises deliberately when exposed to moisture[4]
Electrical & ESD propertiesNot documentedProto-pasta magnetic iron PLA is ferromagnetic and responds to magnets[4]
Health & Safety
Fume toxicity1–5Moderate — measurable VOCs and UFPs, ventilation advised[27]Low hazard — minimal VOC and particle emission[27]
VOC emission rateµg/minUp to 180 caprolactam, the dominant VOC from nylon and the largest single-VOC rate in the study[27]Not documented
Ultrafine-particle emission rateparticles/min≈2 × 10⁸ median for nylon — low for particles despite the highest VOC mass measured[27]Not documented
Hazardous species emittedCaprolactam, at up to 180 µg/min from nylon filament[27]Not documented
Ventilation / filtration requirement1–5Ventilated room or enclosure recommended[27]None needed in a normal room[27]
Post-Processing
Sanding & machiningNot documentedPolishing is the intended finish — colorFabb and Proto-pasta both sell these grades to be sanded and buffed to a metallic shine[2][3][8]
Dimensional accuracy & detailNot documentedcolorFabb notes the metal fill increases die swell, so flow needs raising above plain PLA[3]
Solvents & Solubility
Soluble inFormic acid, phenol, m-cresol and hexafluoroisopropanol dissolve the matrix at 23 °C, leaving the fibre; laboratory reagents.[28]Chloroform dissolves the PLA matrix (10 % w/v, 2–4 h at 23 °C) and leaves the filler as loose sludge; laboratory reagent.[29]
Softened or crazed byZinc chloride solutions stress-crack the nylon matrix, alcoholic calcium chloride dissolves it, mineral acids attack it.[28]Acetone, ethyl acetate and toluene plasticise the matrix but dissolve <1 % even at 65 °C; acetone submersion crazes parts.[29][30]
Solvent welding & smoothing agentNone — nylon's only solvents (formic acid, phenol, HFIP) degrade the part, and the fibre blocks surface flow anyway.[28]Chloroform vapour attacks only the resin fraction, so the filler is left standing proud; no workshop-safe agent exists.[31][30]

Material entries describe families or representative grades, not an interchangeable specification for every spool. Test methods, orientations and conditions may differ. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.

Sources for this comparison

  1. PA (Nylon) — material basics Polymaker Wiki · 2026-08 · doc
  2. bronzeFill technical data sheet colorFabb · 2026-08 · tds
  3. copperFill technical data sheet colorFabb · 2026-08 · tds
  4. Magnetic Iron PLA — product page and technical data Proto-pasta · 2026-08 · tds
  5. Bambu Filament Technical Data Sheet — PLA Sparkle Bambu Lab · 2026-08 · tds
  6. PLA Metal — product page Bambu Lab US Store · 2026-08 · vendor
  7. Bambu Filament Technical Data Sheet V3.0 — PLA Metal Bambu Lab · 2026-08 · tds
  8. Stainless Steel PLA — product page and technical data Proto-pasta · 2026-08 · tds
  9. PLA Sparkle — product page Bambu Lab US Store · 2026-08 · vendor
  10. bronzeFill — product page colorFabb US · 2026-08 · vendor
  11. Polymaker product catalogue Polymaker · 2026-08 · vendor
  12. 3DXTech product catalogue 3DXTech · 2026-08 · vendor
  13. Proto-pasta product catalogue Proto-pasta · 2026-08 · vendor
  14. Max volumetric speed Prusa Knowledge Base · 2026-08 · doc
  15. Fiberon PA6-CF20 Technical Data Sheet V1.1 Polymaker · 2024-12 · tds
  16. Composite materials filled with carbon, kevlar or glass Prusa Knowledge Base · 2026-08 · doc
  17. Wet Filament — signs, causes and drying Polymaker Wiki · 2026-08 · doc
  18. Bambu Filament Technical Data Sheet V3.0 — PLA Basic Bambu Lab · 2026-08 · tds
  19. PolyLite PLA Technical Data Sheet V5.4 Polymaker · 2024-11 · tds
  20. PolyMide CoPA Technical Data Sheet V5.4 (dry and wet status blocks) Polymaker · 2024-11 · tds
  21. Moisture Conditioning — effect on printed nylon properties Polymaker Wiki · 2026-08 · doc
  22. BambuLab PLA Basic vs PLA Tough vs PLA-CF — results spreadsheet My Tech Fun (Igor Gaspar) · 2026-08 · test
  23. Polymaker PLA Pro vs PLA-CF — results spreadsheet My Tech Fun (Igor Gaspar) · 2026-08 · test
  24. Carbon Fiber PLA vs META-PLA vs PLA+ vs PLA by Sunlu — results spreadsheet My Tech Fun (Igor Gaspar) · 2026-08 · test
  25. Mechanical Properties of Additively Manufactured Polymeric Materials — PLA and PETG — For Biomechanical Applications Polymers 16(13):1868 · 2024-06 · paper
  26. PLA — material guide Prusa Knowledge Base · 2026-08 · doc
  27. Emissions of Ultrafine Particles and Volatile Organic Compounds from Commercially Available Desktop Three-Dimensional Printers with Multiple Filaments (Azimi et al.) Environmental Science & Technology 50(3) 1260-1268 · 2016-01 · paper
  28. Ultramid Nylon Chemical Resistance guide (unmodified PA6 B27E and PA66 A27E) BASF · 2026-08 · tds
  29. Solubility Study of Ingeo Biopolymer Grades in Common Organic Solvents (NWPD003) NatureWorks · 2019-10 · tds
  30. Improve your 3D prints with chemical smoothing Prusa Research · 2026-08 · doc
  31. Effect of vapour smoothing in trichloromethane on 3D printed PLA — surface, mechanical and chemical structure Pitale, Keche & Chopra, Engineering Research Express 6(4) 045579 · 2024-12 · paper